Nissan Juke (2016 year). Service Repair Manual — part 675
DUCT AND GRILLE
VTL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
3. Disengage fixing pawls (A), and then remove center ventilator
grille.
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER NOZZLE
SIDE DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000012199142
REMOVAL
Driver Side
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove fixing screws (A), and then remove side defroster noz-
zle.
Passenger Side
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove fixing screws (A), and then remove instrument panel
bracket (1).
3. Remove fixing screw (B), and then remove side defroster nozzle
(2).
INSTALLATION
Install in the reverse order of removal.
SIDE VENTILATOR GRILLE
SIDE VENTILATOR GRILLE : Removal and Installation
INFOID:0000000012199143
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
JMIIA0840ZZ
JMIIA1042ZZ
JMIIA1041ZZ
Revision: November 2015
2016 JUKE
VTL-10
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
2. Remove fixing screws (A), and then remove side ventilator grille.
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER GRILLE
SIDE DEFROSTER GRILLE : Removal and Installation
INFOID:0000000012199144
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove side defroster nozzle. Refer to
VTL-9, "SIDE DEFROSTER NOZZLE : Removal and Installation"
.
3. Remove fixing screw (A) and disengage fixing pawl (B), and
then remove side defroster grille.
INSTALLATION
Install in the reverse order of removal.
FRONT DEFROSTER NOZZLE
FRONT DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000012199145
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove side defroster nozzle. Refer to
VTL-9, "SIDE DEFROSTER NOZZLE : Removal and Installation"
.
3. Remove fixing screw (A), and then remove front defroster noz-
zle.
INSTALLATION
Install in the reverse order of removal.
CENTER VENTILATOR DUCT
JMIIA0845ZZ
JMIIA0846ZZ
JMIIA0843ZZ
Revision: November 2015
2016 JUKE
DUCT AND GRILLE
VTL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
CENTER VENTILATOR DUCT : Removal and Installation
INFOID:0000000012199146
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove side defroster nozzle LH and RH. Refer to
VTL-9, "SIDE DEFROSTER NOZZLE : Removal and
.
3. Remove front defroster nozzle. Refer to
VTL-10, "FRONT DEFROSTER NOZZLE : Removal and Installa-
4. Remove fixing screws (A), and then remove center ventilator
duct.
INSTALLATION
Install in the reverse order of removal.
SIDE VENTILATOR DUCT
SIDE VENTILATOR DUCT : Removal and Installation
INFOID:0000000012199147
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Remove fixing screws (A), and then remove side ventilator duct.
INSTALLATION
Install in the reverse order of removal.
REAR HEATER DUCT 1
REAR HEATER DUCT 1 : Removal and Installation
INFOID:0000000012199148
REMOVAL
1. Remove center console assembly. Refer to
IP-24, "Removal and Installation"
.
JMIIA1043ZZ
Driver side
Passenger side
JMIIA0847ZZ
Revision: November 2015
2016 JUKE
VTL-12
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
2. Disengage fixing pawls, and then remove rear heater duct 1.
(Models for Canada only)
INSTALLATION
Install in the reverse order of removal.
REAR HEATER DUCT 2
REAR HEATER DUCT 2 : Removal and Installation
INFOID:0000000012199149
REMOVAL
1. Remove center console assembly. Refer to
IP-24, "Removal and Installation"
2. Remove front seat assembly. Refer to
SE-21, "Removal and Installation"
3. Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER :
.
4. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
5. Remove dash side finisher. Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
.
6. Remove rear heater duct 2. (Models for Canada only)
• Peel off floor carpet (1).
• Remove rear heater duct 3 (2) from rear heater duct 2 (3).
• Remove front floor spacer, and then remove rear heater duct 2
(2) from rear heater duct 1 (1).
INSTALLATION
Install in the reverse order of removal.
REAR HEATER DUCT 3
REAR HEATER DUCT 3 : Removal and Installation
INFOID:0000000012199150
REMOVAL
: Pawl
JMIIA0848ZZ
: Vehicle front
JMIIA0849ZZ
: Vehicle front
JMIIA0850ZZ
Revision: November 2015
2016 JUKE
DUCT AND GRILLE
VTL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
1. Remove center console assembly. Refer to
IP-24, "Removal and Installation"
.
2. Remove front seat assembly. Refer to
SE-21, "Removal and Installation"
3. Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER :
.
4. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
5. Remove dash side finisher. Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
.
6. Remove rear heater duct 3. (Models for Canada only)
• Peel off floor carpet (1).
• Remove rear floor spacer, and then remove rear heater duct 3
(2) from rear heater duct 2 (3).
INSTALLATION
Install in the reverse order of removal.
FOOT DUCT
FOOT DUCT : Removal and Installation
INFOID:0000000012199151
REMOVAL
Driver Side
1. Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
2. Disconnect harness connector.
3. Remove harness connector fixing clamp.
4. Remove fixing screws, and then remove foot duct LH.
Passenger Side
1. Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2. Remove fixing screws, and then remove foot duct RH.
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMIIA0849ZZ
Revision: November 2015
2016 JUKE
V
T
L
- 1
4
< REMOVAL AND INSTALLATION >
BLOWER MOTOR
BLOWER MOTOR
Exploded View
INFOID:0000000012199152
*1: Manual air conditioning
*2: Automatic air conditioning
Removal and Installation
INFOID:0000000012199153
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1. Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2. Disconnect blower motor harness connector (1) and front pas-
senger air bag module harness connector (2).
3. Remove front passenger air bag module. Refer to
SR-18, "Removal and Installation"
1.
A/C unit assembly
2.
Blower fan resistor
*1
3.
Sub harness
*1
4.
Power transistor
*2
5.
Sub harness
*2
6.
Blower motor
JPIIA1549ZZ
JMIIA1044ZZ
Revision: November 2015
2016 JUKE
BLOWER MOTOR
VTL-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
4. Press flange holding hook (A), and then turn blower motor (1)
clockwise.
5. Pull outside, and then remove blower motor.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old mounting bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JPIIA1692ZZ
Revision: November 2015
2016 JUKE
VTL-16
< REMOVAL AND INSTALLATION >
IN-CABIN MICROFILTER
IN-CABIN MICROFILTER
Exploded View
INFOID:0000000012199154
Removal and Installation
INFOID:0000000012199155
REMOVAL
1. Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2. Remove filter cover (1), and then remove in-cabin microfilter (2).
CAUTION:
If the filter is deformed/damaged when removing, replace it
with a new one. Deformed/damaged filter may deteriorate
the dust collecting performance.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, handle the filter with extreme care to avoid deforming/damaging.
Replacement
INFOID:0000000012199156
Replace In-cabin microfilter.
VTL-17, "In-cabin microfilter"
.
1.
A/C unit assembly
2.
In-cabin microfilter
3.
Filter cover
JPIIA1679ZZ
JPIIA1683ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст