Nissan Juke (2016 year). Service Repair Manual — part 676
SERVICE DATA AND SPECIFICATIONS (SDS)
VTL-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
In-cabin microfilter
INFOID:0000000012199157
Replacement interval
MA-7, "Introduction of Periodic Maintenance"
Revision: November 2015
2016 JUKE
WCS
WCS-1
DRIVER INFORMATION & MULTIMEDIA
C
D
E
F
G
H
I
J
K
L
M
B
SECTION
WCS
A
O
P
CONTENTS
WARNING CHIME SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
Combination Meter . . . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
WARNING CHIME SYSTEM . . . . . . . . . ...
WARNING CHIME SYSTEM : System Diagram . ...
WARNING CHIME SYSTEM : System Description
. ..
WARNING CHIME SYSTEM : Fail-Safe . . . . ...
LIGHT REMINDER WARNING CHIME . . . . . ...
LIGHT REMINDER WARNING CHIME : System
Diagram . . . . . . . . . . . . . . . . .....
LIGHT REMINDER WARNING CHIME : System
Description . . . . . . . . . . . . . . . ....
SEAT BELT WARNING CHIME . . . . . . . .
SEAT BELT WARNING CHIME : System Diagram
.
SEAT BELT WARNING CHIME : System Descrip-
tion . . . . . . . . . . . . . . . . . . ..
PARKING BRAKE RELEASE WARNING CHIME .
PARKING BRAKE RELEASE WARNING CHIME
: System Diagram . . . . . . . . . . . . .
PARKING BRAKE RELEASE WARNING CHIME
: System Description . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (COMBINATION
METER) . . . . . . . . . . . . . . . ..
CONSULT Function . . . . . . . . . . . . .
DIAGNOSIS SYSTEM (BCM) . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
BUZZER . . . . . . . . . . . . . . . . . .
BUZZER : CONSULT Function (BCM - BUZZER) .
ECU DIAGNOSIS INFORMATION . . . ..
COMBINATION METER . . . . . . . . ...
Reference Value . . . . . . . . . . . . . ..
Fail-Safe . . . . . . . . . . . . . . . . ..
DTC Index . . . . . . . . . . . . . . . ...
BCM (BODY CONTROL MODULE) . . . . .
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
WARNING CHIME SYSTEM . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
COMBINATION METER . . . . . . . . . . .
COMBINATION METER : Diagnosis Procedure . .
METER BUZZER CIRCUIT . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ..
SEAT BELT BUCKLE SWITCH SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ..
Revision: November 2015
2016 JUKE
WCS-2
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ....
PARKING BRAKE SWITCH SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE LIGHT REMINDER WARNING DOES
NOT SOUND . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE SEAT BELT WARNING CONTINUES
SOUNDING, OR DOES NOT SOUND . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Revision: November 2015
2016 JUKE
WCS
PRECAUTIONS
WCS-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012201459
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000012926050
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
• For vehicles with the engine listed below, remove the battery termi-
nal after a lapse of the specified time:
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait
for at least 15 minutes to remove the battery terminal.
NOTE:
D4D engine
: 20 minutes
YS23DDT
: 4 minutes
HRA2DDT
: 12 minutes
YS23DDTT
: 4 minutes
K9K engine
: 4 minutes
ZD30DDTi
: 60 seconds
M9R engine
: 4 minutes
ZD30DDTT
: 60 seconds
R9M engine
: 4 minutes
V9X engine
: 4 minutes
YD25DDTi
: 2 minutes
SEF289H
Revision: November 2015
2016 JUKE
WCS-4
< PRECAUTION >
PRECAUTIONS
• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.
• Example of high-load driving
- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.
- Driving for 30 minutes or more on a steep slope.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Revision: November 2015
2016 JUKE
WCS
COMPONENT PARTS
WCS-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000012201461
Component Description
INFOID:0000000012201462
1.
Parking brake switch
2.
Combination meter
3.
ABS actuator and electric unit (con-
trol unit)
Refer to
4.
SYSTEM : Component Parts Loca-
tion"
5.
Seat belt buckle switch (driver side)
JSNIA3559ZZ
Unit
Description
Combination meter
• Receives a buzzer output signal from the BCM with CAN communication line and sounds the
buzzer.
• Judges whether the parking brake is released from the vehicle speed signal received from the
ABS actuator and electric unit (control unit) with CAN communication line and the parking
brake switch signal from the parking brake switch, and sounds the buzzer if necessary.
BCM
Based on the signals received from various units and switches, transmits the buzzer output sig-
nal to the combination meter via CAN communication.
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to combination meter via CAN communication.
Seat belt buckle switch (driver
side)
Transmits a seat belt buckle switch signal (driver side) to the combination meter.
Combination switch
(Lighting switch)
Transmits the combination switch signal to BCM.
Front door switch (driver side)
Transmits the driver side door switch signal to BCM.
Parking brake switch
Transmits the parking brake switch signal to the combination meter.
Revision: November 2015
2016 JUKE
WCS-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Combination Meter
INFOID:0000000012201463
The buzzer (1) for the warning chime system is integrated in the
combination meter.
JSNIA3231ZZ
Revision: November 2015
2016 JUKE
WCS
SYSTEM
WCS-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYSTEM
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Diagram
INFOID:0000000012201464
WARNING CHIME SYSTEM : System Description
INFOID:0000000012201465
COMBINATION METER
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST
WARNING CHIME SYSTEM : Fail-Safe
INFOID:0000000012201466
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
JSNIA3116GB
Warning functions
Out line
Warning judgment unit
Refer to
Light reminder warning chime
The warning chime sounds when the ignition
switch is in OFF or ACC position with the com-
bination switch (lighting switch) in the 1st or
2nd position and the driver side door open.
BCM
WCS-9,
"LIGHT RE-
MINDER
WARNING
CHIME : Sys-
tem Descrip-
tion"
Seat belt warning chime
The warning chime sounds when the driver
seat belt is unfastened with the ignition switch
in ON position.
BCM
WCS-10,
"SEAT BELT
WARNING
CHIME : Sys-
tem Descrip-
tion"
Parking brake release warning chime
The warning chime sounds when the ignition
switch is in ON position with the parking brake
in operation and the vehicle speed 7 km/h (4.3
MPH) or more.
Combination meter
WCS-12,
"PARKING
BRAKE RE-
LEASE WARN-
ING CHIME :
System De-
scription"
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст