Nissan Juke (2016 year). Service Repair Manual — part 130
P1813 AWD MODE SWITCH
DLN-47
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1813 AWD MODE SWITCH
DTC Logic
INFOID:0000000012199386
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Change AWD mode switch following order.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1813” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199387
1.
CHECK AWD MODE SWITCH
Check AWD mode switch. Refer to
DLN-48, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace AWD mode switch. Refer to
DLN-93, "Removal and Installation"
.
2.
CHECK AWD MODE SWITCH CIRCUIT (1)
1. Disconnect AWD control module harness connector.
2. Check the continuity between AWD control module harness connector and AWD mode switch harness
connector.
DTC
Display item
Malfunction detected condition
Possible cause
P1813
4WD MODE SW
Multiple signals received from AWD
mode switch are detected.
• AWD mode switch
- Internal malfunction of AWD mode
switch
- Malfunction of AWD mode switch cir-
cuit
• AWD control module
Changing order
: 2WD
→
AWD-V
→
AWD
→
AWD-V
→
2WD
Revision: November 2015
2016 JUKE
DLN-48
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1813 AWD MODE SWITCH
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD MODE SWITCH CIRCUIT (2)
Check the continuity between AWD mode switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK TERMINALS AND HARNESS CONNECTORS
• Check AWD control module pin terminals for damage or loose connection with harness connector.
• Check AWD mode switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
Component Inspection
INFOID:0000000012199388
1.
CHECK AWD MODE SWITCH
1. Turn the ignition switch OFF.
2. Remove AWD mode switch. Refer to
DLN-93, "Removal and Installation"
.
3. Check the continuity between AWD mode switch harness connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
AWD control module
AWD mode switch
Continuity
Connector
Terminal
Connector
Terminal
B47
9
M48
1
Existed
5
Not existed
6
Not existed
13
1
Not existed
5
Existed
6
Not existed
21
1
Not existed
5
Not existed
6
Existed
AWD mode switch
—
Continuity
Connector
Terminal
M48
3
Ground
Not existed
AWD switch assembly
Condition
Continuity
Terminal
1
3
AWD mode switch: 2WD
Not existed
AWD mode switch: AWD-V or AWD
Existed
5
3
AWD mode switch: 2WD
Existed
AWD mode switch: AWD-V or AWD
Not existed
6
3
AWD mode switch: 2WD or AWD-V
Not existed
AWD mode switch: AWD
Existed
Revision: November 2015
2016 JUKE
P1813 AWD MODE SWITCH
DLN-49
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NO
>> Replace AWD mode switch. Refer to
DLN-93, "Removal and Installation"
.
Revision: November 2015
2016 JUKE
DLN-50
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181B INCOMPLETE SELFSHUT
P181B INCOMPLETE SELFSHUT
DTC Logic
INFOID:0000000012199389
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF, and wait for several seconds.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181B” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199390
1.
CHECK AWD CONTROL MODULE POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect AWD control module harness connector.
3. Check the voltage between AWD control module harness connector and ground.
4. Turn the ignition switch ON.
CAUTION:
Never start the engine.
5. Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AWD CONTROL MODULE POWER SUPPLY (2)
1. Turn the ignition switch OFF.
2. Check the 10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).
3. Check the harness for open or short between AWD control module harness connector No.1 terminal and
10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).
Is the inspection result normal?
DTC
Display item
Malfunction detected condition
Possible cause
P181B
INCOMP SELF SHUT
When ignition switch is OFF and AWD
control module power supply is lower or
higher than normal
Self-shut of AWD control module is in-
complete.
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
Revision: November 2015
2016 JUKE
P181B INCOMPLETE SELFSHUT
DLN-51
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
YES
>> Perform the trouble diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD CONTROL MODULE GROUND
1. Turn the ignition switch OFF.
2. Check the continuity between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181B”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
AWD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
Revision: November 2015
2016 JUKE
DLN-52
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181D ENGINE TORQUE SIGNAL
P181D ENGINE TORQUE SIGNAL
DTC Logic
INFOID:0000000012199391
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181D” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199392
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(Except for NISMO
(For NISMO RS).
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181D”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181D
ENGINE SYSTEM
Malfunction is detected in engine torque
signal that is output from ECM through
CAN communication.
• ECM
• AWD control module
• CAN communication line
Revision: November 2015
2016 JUKE
P181E STEERING ANGLE SENSOR
DLN-53
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P181E STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000012199393
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199394
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC “C1143” detected?
YES
>> Proceed to
BRC-108, "Diagnosis Procedure"
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181E”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181E
STR ANGLE SEN
Malfunction is detected in steering angle
sensor signal through CAN communica-
tion.
• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor
circuit
• Malfunction of AWD control module
• CAN communication line
Revision: November 2015
2016 JUKE
DLN-54
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181F INCOMPLETE CALIBRATION
P181F INCOMPLETE CALIBRATION
DTC Logic
INFOID:0000000012199395
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181F” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199396
1.
PERFORM WRITING UNIT CHARACTERISTICS
1. Erase self-diagnostic result for “ALL MODE AWD/4WD”.
2. Perform writing unit characteristics. Refer to
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC except “P181F” detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS AGAIN
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
Is DTC “P181F” detected?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Check AWD control module pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181F
INCOMP CALIBRATION
When incomplete writing unit character-
istics of rear final drive is detected.
Writing unit characteristics is incom-
plete.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст