Nissan Juke (2016 year). Service Repair Manual — part 543
RF-12
< WIRING DIAGRAM >
SUNROOF MOTOR ASSEMBLY
WIRING DIAGRAM
SUNROOF MOTOR ASSEMBLY
Wiring Diagram
INFOID:0000000012196961
JRKWF4437GB
Revision: November 2015
2016 JUKE
SUNROOF MOTOR ASSEMBLY
RF-13
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
JRKWF4438GB
Revision: November 2015
2016 JUKE
RF-14
< WIRING DIAGRAM >
SUNROOF MOTOR ASSEMBLY
JRKWF4439GB
Revision: November 2015
2016 JUKE
SUNROOF MOTOR ASSEMBLY
RF-15
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
JRKWF4440GB
Revision: November 2015
2016 JUKE
RF-16
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
WorkFlow
INFOID:0000000012196962
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 4.
4.
IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES
>> INSPECTION END
NO
>> GO TO 3.
Revision: November 2015
2016 JUKE
INSPECTION AND ADJUSTMENT
RF-17
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000012196963
MEMORY RESET PROCEDURE
1. Please observe the following instructions at confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops (to wipe-out the memory of lid position and operating friction).
2. Initialization of system should be conducted after the following conditions.
• When the sunroof motor is changed.
• When the sunroof does not operate normally. (Incomplete initialization conditions)
Refer to
RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000012196964
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Press tilt up switch several times and set glass lid to the tilt up position.
2. Release the tilt up switch once, press the tilt up switch again, press and hold the switch until lid pops up.
3. The glass lid moves slight toward tilt up direction then stop. (Press and hold the switch during this opera-
tion)
4. Release the switch again, and press the tilt up switch within the first 4 seconds. (Press and hold the
switch)
5. After 4 seconds, the glass lid will be automatically operated in sequence of tilt down, slide open and slide
close.
6. After the glass lid stops, release the switch 0.5 second later. (Press and hold the switch during this opera-
tion)
7. If slide switch operates normally, this initialization is done.
ANTI-PINCH FUNCTION
1. Full open the sunroof.
2. Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3. Close the sunroof completely with auto-slide close.
Check that sunroof lowers for approximately 150 mm (5.91in) or 2 seconds with out pinching a wooden piece
and stops.
CAUTION:
• Never check with hands and other part of body because they may be pinched. Never get pinched.
• Depending on environment and driving conditions, if a similar impact or lord is applied to the sun-
roof it may lower.
• Check that auto-slide operates before inspection when system initialization is performed.
• Perform initial setting when auto-slide operation or anti-pinch function does not operate normally.
Revision: November 2015
2016 JUKE
RF-18
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000012196965
SUNROOF MOTOR ASSEMBLY
1.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sunroof motor assembly harness connector.
3. Check continuity between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK POWER SUPPLY CIRCUIT-I
Check voltage between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK SUNROOF MOTOR CIRCUIT-I
1. Disconnect BCM harness connector.
2. Check continuity between BCM harness connector and sunroof motor assembly harness connector.
3. Check continuity between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> Check BCM. Refer to
NO
>> Repair or replace harness or connector.
4.
CHECK POWER SUPPLY CIRCUIT-II
1. Turn ignition switch ON.
2. Check voltage between sunroof motor assembly harness connector and ground.
Sunroof motor assembly
Ground
Continuity
Connector
Terminal
R11
1
Existed
(+)
(–)
Voltage (V)
(Approx.)
Sunroof motor assembly
Connector
Terminal
R11
6
Ground
Battery Voltage
BCM
Sunroof motor assembly
Continuity
Connector
Terminal
Connector
Terminal
M69
69
R11
6
Existed
Sunroof motor assembly
Ground
Continuity
Connector
Terminal
R11
6
Not existed
Revision: November 2015
2016 JUKE
POWER SUPPLY AND GROUND CIRCUIT
RF-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK SUNROOF MOTOR CIRCUIT-II
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check continuity between BCM harness connector and sunroof motor assembly harness connector.
4. Check continuity between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> Check BCM. Refer to
.
NO
>> Repair or replace harness or connector.
(+)
(–)
Voltage (V)
(Approx.)
Sunroof motor assembly
Connector
Terminal
R11
3
Ground
Battery Voltage
BCM
Sunroof motor assembly
Continuity
Connector
Terminal
Connector
Terminal
M69
68
R11
3
Existed
Sunroof motor assembly
Ground
Continuity
Connector
Terminal
R11
3
Not existed
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст