Nissan Juke (2016 year). Service Repair Manual — part 542
RF-4
< PRECAUTION >
PRECAUTIONS
(Turning it ON outside the lamp case may cause fire or visual impairments.)
• Never touch the bulb glass immediately after turning it OFF. It is extremely hot.
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-
tor, the housing, etc. by high-voltage leakage or corona discharge.)
• Never perform HID circuit inspection with a tester.
• Never touch the xenon bulb glass with hands. Never put oil and grease on it.
• Dispose of the used xenon bulb after packing it in thick vinyl without breaking it.
• Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).
Precautions for Removing Battery Terminal
INFOID:0000000012964841
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
• For vehicles with the engine listed below, remove the battery termi-
nal after a lapse of the specified time:
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait
for at least 15 minutes to remove the battery terminal.
NOTE:
• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.
• Example of high-load driving
- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.
- Driving for 30 minutes or more on a steep slope.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
D4D engine
: 20 minutes
YS23DDT
: 4 minutes
HRA2DDT
: 12 minutes
YS23DDTT
: 4 minutes
K9K engine
: 4 minutes
ZD30DDTi
: 60 seconds
M9R engine
: 4 minutes
ZD30DDTT
: 60 seconds
R9M engine
: 4 minutes
V9X engine
: 4 minutes
YD25DDTi
: 2 minutes
SEF289H
Revision: November 2015
2016 JUKE
PREPARATION
RF-5
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000012196953
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000012196954
Tool number
(TechMate No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rattle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls and metal clips
SIIA0995E
JMKIA3050ZZ
Revision: November 2015
2016 JUKE
RF-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000012196955
Component Description
INFOID:0000000012196956
JMKIA5998ZZ
1.
Sunroof motor assembly
2.
Sunroof switch
3.
Combination meter
4.
SYSTEM : Component Parts Loca-
tion"
5.
Front door switch
A.
View with headlining removed
Component
Function
BCM
Supplies the power supply to sunroof motor assembly.
Combination meter
Transmits vehicle speed signal to sunroof motor assembly.
Front door switch
Detects door open/close condition and transmits to BCM.
Sunroof motor assembly
It is sunroof motor and CPU integrated type that enables tilt up/down & slide open/close by sun-
roof switch operation.
Sunroof switch
Transmits tilt up/down & slides open/close operation signal to sunroof motor assembly.
Revision: November 2015
2016 JUKE
SYSTEM
RF-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SYSTEM
System Diagram
INFOID:0000000012196957
SUNROOF
System Description
INFOID:0000000012196958
SUNROOF SYSTEM
• Sunroof motor assembly operates with the power supply that is output from BCM while ignition switch is ON
or retained power is operating.
• Tilt up/down & slide open/close signals from sunroof switch enables operate sunroof motor to move arbi-
trarily.
• Sunroof motor assembly receives a vehicle speed signal from combination meter and controls the sunroof
motor operation.
OPERATION DESCRIPTION
The sunroof operate to the following condition by the sunroof switch operation.
JMKIA5324GB
Sunroof position before operation
Switch operation
Sunroof action
Sunroof position after operation
Tilt up
A: Glass lid
B: Roof panel
Close
Not action
—
Open
Close
Fully-closed
JMKIA5777ZZ
JMKIA5869ZZ
Revision: November 2015
2016 JUKE
RF-8
< SYSTEM DESCRIPTION >
SYSTEM
Tilt halfway-open
A: Glass lid
B: Roof panel
Close
Tilt up
Tilt up
Open
Close
Fully-closed
Fully-closed
A: Glass lid
B: Roof panel
Close
Tilt up
Tilt up
Open
Open
Fully-open
Halfway-open
A: Glass lid
B: Roof panel
Close
Close
Fully-closed
Open
Open
Fully-open
Fully-open
A: Glass lid
B: Roof panel
Close
Close
Fully-closed
Open
Not action
—
Sunroof position before operation
Switch operation
Sunroof action
Sunroof position after operation
JMKIA5778ZZ
JMKIA5870ZZ
JMKIA5869ZZ
JMKIA5779ZZ
JMKIA5870ZZ
JMKIA5871ZZ
JMKIA5780ZZ
JMKIA5872ZZ
JMKIA5871ZZ
JMKIA5781ZZ
JMKIA5872ZZ
Revision: November 2015
2016 JUKE
SYSTEM
RF-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
AUTO OPERATION
Sunroof AUTO feature makes it possible to slide open and slide close or tilt up and tilt down the sunroof with-
out holding the sunroof switch in the slide open/tilt down or slide close/tilt up position.
RETAINED POWER OPERATION
Retained power operation is an additional power supply function that enables sunroof system to operate dur-
ing 45 seconds even when ignition switch is turned OFF.
RETAINED POWER FUNCTION CANCEL CONDITIONS
• Front door CLOSE (door switch OFF)
→
OPEN (door switch ON).
• When ignition switch is ON again.
• When timer time passes. (45 seconds)
ANTI-PINCH FUNCTION
The CPU of sunroof motor assembly monitors the sunroof motor operation and the sunroof position (fully-
closed or other) by the signals from sunroof motor.
When sunroof motor detects an interruption during the following slide close and tilt down operation, sunroof
switch controls the motor for open and the sunroof will operate until full up position (when tilt down operate) or
150 mm (5.91 in) or more in an open direction (when slide close operate).
Revision: November 2015
2016 JUKE
RF-10
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
ECU DIAGNOSIS INFORMATION
BCM (BODY CONTROL MODULE)
List of ECU Reference
INFOID:0000000012196959
ECU
Reference
BCM
BCS-61, "DTC Inspection Priority Chart"
Revision: November 2015
2016 JUKE
SUNROOF SYSTEM
RF-11
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF SYSTEM
Reference Value
INFOID:0000000012196960
TERMINAL LAYOUT
PHYSICAL VALUES
JMKIA2225ZZ
Terminal No.
(Wire color)
Description
Condition
Voltage (V)
(Approx.)
+
–
Signal name
Input/
Output
1
(B)
Ground Ground
—
—
0
3
(L)
Ground Retained power signal
Input
Ignition switch ON
Battery voltage
Within 45 second after ignition
switch is turned to OFF
When driver side or passenger side
door is opened during retained pow-
er operation
0
5
(Y)
Ground Sunroof open signal
Input
Sunroof switch: Open
0
Ignition switch ON
Battery voltage
6
(P)
Ground Sunroof power supply
Input
—
Battery voltage
8
(V)
Ground
Vehicle speed signal (8-
pulse)
Input
Speedometer operated [When vehi-
cle speed is approx.40km/ h
(25MPH)]
10
(G)
Ground Sunroof close signal
Input
Sunroof switch: Close
0
Ignition switch ON
Battery voltage
JSNIA0012GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст