Nissan Juke (2016 year). Service Repair Manual — part 454
INT-38
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
BACK DOOR TRIM
Exploded View
INFOID:0000000012199189
BACK DOOR PULL HANDLE
BACK DOOR PULL HANDLE : Removal and Installation
INFOID:0000000012199190
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the back door panel.
1. Fully open back door.
1.
Back door side finisher RH
2.
Rear parcel shelf finisher
3.
Back door side finisher LH
4.
Back door lower finisher
5.
Emergency lid
6.
Back door pull handle
: Clip
: Pawl
JMJIA4537ZZ
Revision: November 2015
2016 JUKE
BACK DOOR TRIM
INT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2. Disengage back door pull handle fixing pawls with a remover
tool (A), and then remove back door pull handle.
INSTALATION
Install in the reverse order of removal.
BACK DOOR LOWER FINISHER
BACK DOOR LOWER FINISHER : Removal and Installation
INFOID:0000000012199191
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the back door panel.
1. Fully open back door.
2. Remove rear parcel shelf finisher. (Models with rear parcel shelf finisher)
3. Disengage back door lower finisher fixing clips with a remover
tool (A), and then remove back door lower finisher.
INATALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing back door lower finisher, check that clips are securely in back door panel holes, and
press them in.
BACK DOOR SIDE FINISHER
BACK DOOR SIDE FINISHER : Removal and Installation
INFOID:0000000012199192
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the back door panel.
1. Fully open back door.
2. Remove back door lower finisher. Refer to
INT-39, "BACK DOOR LOWER FINISHER : Removal and
.
: Pawl
JMJIA4411ZZ
: Clip
JMJIA4409ZZ
Revision: November 2015
2016 JUKE
INT-40
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
3. Disengage back door side finisher fixing clips (A), and then
remove back door side finisher.
INSTALATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing back door side finisher, check that clips are securely in back door panel holes, and
press them in.
EMERGENCY LID
EMERGENCY LID : Removal and Installation
INFOID:0000000012199193
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
1. Fully open back door.
2. Disengage emergency lid fixing pawls with a remover tool (A),
and then remove emergency lid.
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
INSTALLATION
Install in the reverse order of removal.
JMJIA4410ZZ
: Pawl
JMJIA4412ZZ
Revision: November 2015
2016 JUKE
IP-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
IP
A
B
IP
N
O
P
CONTENTS
INSTRUMENT PANEL
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
Precaution for Procedure without Cowl Top Cover
. ..
Service . . . . . . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ...
CLIP LIST . . . . . . . . . . . . . . .
Clip List . . . . . . . . . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ...
Work Flow . . . . . . . . . . . . . . . . .
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
INSTRUMENT PANEL ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CENTER CONSOLE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Revision: November 2015
2016 JUKE
IP-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012199196
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000012831483
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
• For vehicles with the engine listed below, remove the battery termi-
nal after a lapse of the specified time:
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait
for at least 15 minutes to remove the battery terminal.
NOTE:
D4D engine
: 20 minutes
YS23DDT
: 4 minutes
HRA2DDT
: 12 minutes
YS23DDTT
: 4 minutes
K9K engine
: 4 minutes
ZD30DDTi
: 60 seconds
M9R engine
: 4 minutes
ZD30DDTT
: 60 seconds
R9M engine
: 4 minutes
V9X engine
: 4 minutes
YD25DDTi
: 2 minutes
SEF289H
Revision: November 2015
2016 JUKE
PRECAUTIONS
IP-3
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.
• Example of high-load driving
- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.
- Driving for 30 minutes or more on a steep slope.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000012199198
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Service
INFOID:0000000012199199
• Disconnect battery negative terminal in advance.
• Disconnect air bag system line in advance.
• Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
• Be careful not to scratch pad and other parts.
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts, that may get
in the way with a shop cloth.
• When removing parts with a screwdriver or other tool, cover the tool surface with vinyl tape to protect parts.
• Keep removed parts protected with a shop cloth.
• If a clip is deformed or damaged, replace it.
• If an unreusable part is removed, replace it with a new one.
• Tighten bolts and nuts firmly to the specified torque.
• After reassembly is complete, check that each part functions correctly.
• Remove stains via the following procedure.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping off the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then wipe off the stain with the
cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then wipe off the detergent completely. Then
wipe the area with a soft dry cloth.
• Never use any organic solvent, such as thinner or benzine.
PIIB3706J
Revision: November 2015
2016 JUKE
IP-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000012199200
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000012199201
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
Hook and pick tool
Removes rear console cover
SIIA0995E
JMKIA3050ZZ
JMJIA0490ZZ
Revision: November 2015
2016 JUKE
CLIP LIST
IP-5
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CLIP LIST
Clip List
INFOID:0000000012199202
JMJIA3734GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст