Nissan Juke (2016 year). Service Repair Manual — part 453
INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
SUNROOF : Exploded View
INFOID:0000000012199183
SUNROOF
SUNROOF : Removal and Installation
INFOID:0000000012199184
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
JMJIA4707ZZ
1.
Headlining assembly
2.
Assist grip clip
3.
Rear assist grip RH
4.
Sunroof welt
5.
Front assist grip RH
6.
Sun visor assembly RH
7.
Sun visor cover RH
8.
Sun visor cover LH
9.
Sun visor assembly LH
10. Front roof finisher
11. Rear assist grip LH
12. Headlining clip
13. Sun visor holder RH
14. Map lamp
15. Sun visor holder LH
16. Metal clip
: Clip
: Pawl
Revision: November 2015
2016 JUKE
HEADLINING
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Never damage the body.
1. Remove front pillar garnish (LH and RH). Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and
.
2. Disconnect harness connector (A) from headlining and harness
clips
3. Remove center pillar upper garnish (LH and RH). Refer to
INT-22, "CENTER PILLAR UPPER GARNISH :
.
4. Remove back door weather-strip. Refer to
DLK-152, "BACK DOOR WEATHER-STRIP : Removal and
(with Intelligent Key System).
5. Remove luggage side upper finisher (LH and RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER
6. Remove all assist grips.
1. Disengage pawl of assist grip clip (1) using a remover tool
(A). Slide assist grip clip forward and remove it.
2. Slide assist grip (2) forward and remove it.
3. Remove metal clips.
7. Remove sun visor assembly (LH and RH).
1. Disengage sun visor cover fixing pawls with a remover tool
(A), and then remove sun visor cover.
2. Remove sun visor assembly fixing screws, and then slide toward vehicle rear to remove sun visor
assembly.
8. Remove inside mirror and inside mirror cover. Refer to
MIR-16, "Removal and Installation"
.
9. Remove map lamp assembly. Refer to
INL-46, "Removal and Installation"
10. Remove sunroof welt.
11. Remove front roof finisher.
: Clip
JMJIA4534ZZ
: Pawl
JMJIA4398ZZ
: Pawl
JMJIA4399ZZ
Revision: November 2015
2016 JUKE
INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
1. Disengage front roof finisher fixing pawls with a remover
tool (A).
2. Disconnect harness connector, and then remove front roof
finisher.
12. Remove front seat assembly (passenger). Refer to
SE-21, "Removal and Installation"
.
13. Remove sun visor holder (LH and RH)
Rotate 90
°
. Remove toward vehicle lower.
14. Remove headlining clips.
15. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
• Align sunroof welt connection (A) to (B) when installing sun-
roof welt.
: Pawl
JMJIA4751ZZ
JMJIA4401ZZ
JMJIA4402ZZ
: Vehicle front
JMJIA4708ZZ
Revision: November 2015
2016 JUKE
LUGGAGE FLOOR TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000012199185
2WD models
JMJIA4714ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Seat belt hook LH
(Models with woofer)
8.
Luggage side lower finisher LH
(Models with woofer)
9.
Shock absorber mask LH
(Models with woofer)
10. Luggage floor rear center spacer
(Models with spare tire)
11. Spare tire clamp
(Models with spare tire)
12. Repair kit holder
(Models without spare tire)
13. Luggage rear plate
14. Luggage side lower finisher grille RH 15. Luggage room lamp
16. Shock absorber mask RH
17. Seat belt hook RH
18. Luggage floor box
19. Seat belt hook LH
20. Luggage side lower finisher LH
21. Shock absorber mask LH
22. Luggage side lower finisher grille LH
: Clip
: Pawl
Revision: November 2015
2016 JUKE
INT-34
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
AWD models
: Metal clip
: Vehicle front
JMJIA4715ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Seat belt hook LH
(Models with woofer)
8.
Luggage side lower finisher LH
(Models with woofer)
9.
Shock absorber mask LH
(Models with woofer)
10. Luggage rear plate
11. Luggage side lower finisher grille RH 12. Luggage room lamp
13. Shock absorber mask RH
14. Seat belt hook RH
15. Seat belt hook LH
16. Luggage side lower finisher LH
17. Shock absorber mask LH
18. Luggage side lower finisher grille LH
19. Luggage floor rear spacer LH
20. Spare tire clamp
21. Luggage floor rear spacer RH
: Clip
: Pawl
: Metal clip
: Vehicle front
Revision: November 2015
2016 JUKE
LUGGAGE FLOOR TRIM
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000012199186
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVE
1. Remove back door weather-strip. Refer to
DLK-152, "BACK DOOR WEATHER-STRIP : Removal and
(with Intelligent Key System).
2. Disengage luggage rear plate fixing metal clip with a remover
tool (A), and then remove luggage rear plate.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing luggage rear plate, check that metal clips are securely in body panel holes, and press
them in.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000012199187
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove luggage room lamp. Refer to
INL-49, "Removal and Installation"
2. Remove luggage floor board.
3. Remove luggage floor box (Models with 2WD).
4. Remove luggage rear plate. Refer to
INT-35, "LUGGAGE REAR PLATE : Removal and Installation"
5. Remove rear body side welt. Refer to
INT-21, "BODY SIDE WELT : Removal and Installation"
6. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
7. Remove rear seat back. Refer to
SE-33, "SEATBACK : Removal and Installation"
.
8. Remove side hinge of seatback hinge. Refer to
SE-38, "SEATBACK HINGE : Removal and Installation"
9. Disengage luggage side lower finisher fixing clips with a
remover tool (A), and then remove luggage side lower finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
: Metal clip
JMJIA4404ZZ
: Clip
JMJIA4405ZZ
Revision: November 2015
2016 JUKE
INT-36
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
CAUTION:
When installing luggage side lower finisher, check that clips are securely in body panel holes, and
press them in.
Removal and Installation of Shock Absorber Mask
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1. Disengage shock absorber mask fixing pawls with a remover
tool (A), and then remove shock absorber mask.
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Luggage Side Lower Finisher Grille
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
Disengage luggage side lower finisher grille fixing pawls with a
remover tool (A), and then remove luggage side lower finisher grille.
CAUTION:
Apply protective tape (B) on the parts to protect it from damage.
INSTALLATION
Install in the reverse order of removal.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and Installation
INFOID:0000000012199188
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove luggage side lower finisher. Refer to
INT-35, "LUGGAGE SIDE LOWER FINISHER : Removal
2. Remove rear seat belt (floor) anchor bolt. Refer to
SB-13, "SEAT BELT RETRACTOR : Removal and
.
: Pawl
JMJIA4407ZZ
: Pawl
JMJIA4408ZZ
Revision: November 2015
2016 JUKE
LUGGAGE FLOOR TRIM
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Disengage luggage side upper finisher fixing clips and metal
clips with a remover tool (A), and then remove luggage side
upper finisher.
INSTALATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing luggage side upper finisher, check that clips, and metal clips are securely in body
panel holes, and press them in.
: Clip
: Metal clip
JMJIA4406ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст