Nissan Juke (2016 year). Service Repair Manual — part 74
CORROSION PROTECTION
BRM-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
: Vehicle front
: Sealed portions
JSKIA2135ZZ
Revision: November 2015
2016 JUKE
BRM-28
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
Body Sealing (AWD Models)
INFOID:0000000012199835
The following figure shows the areas that are sealed at the factory. Sealant that is applied to these areas
should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant
and not to allow other unaffected parts to come into contact with the sealant.
Standard roof models
With sunroof models
: Vehicle front
: Sealed portions
JSKIA2199ZZ
Revision: November 2015
2016 JUKE
CORROSION PROTECTION
BRM-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
: Vehicle front
: Sealed portions
JSKIA5309ZZ
Revision: November 2015
2016 JUKE
BRM-30
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
: Vehicle front
: Sealed portions
JSKIA2202ZZ
Revision: November 2015
2016 JUKE
BODY CONSTRUCTION
BRM-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
BODY CONSTRUCTION
Body Construction (Standard roof Models)
INFOID:0000000012199836
1.
Outer side body
2.
Outer front pillar reinforcement
3.
Upper inner front pillar
4.
Lower dash
5.
Hoodledge reinforcement
6.
Lower front pillar hinge brace
7.
Weld nut
8.
Side dash
9.
Inner front pillar reinforcement
JSKIA2203ZZ
Revision: November 2015
2016 JUKE
BRM-32
< REMOVAL AND INSTALLATION >
BODY CONSTRUCTION
10. Upper hinge plate
11. Lower hinge plate
12. Lower front pillar bulkhead
13. Inner front pillar reinforcement
14. Front floor reinforcement
15. Front floor
16. Front outrigger
17. Inner sill
18. Outer sill reinforcement
19. Inner center pillar reinforcement
20. Inner center pillar
21. Center pillar reinforcement
22. Center pillar hinge brace
23. Inner sill reinforcement
24. Center sill reinforcement
25. Inner sill extension
26. Inner rear wheelhouse
27. Outer rear wheelhouse
28. Rear roof rail brace
29. Inner rear pillar reinforcement
30. Rear fender extension
31. Inner rear pillar
32. Inner rear wheelhouse reinforce-
ment
Revision: November 2015
2016 JUKE
BODY CONSTRUCTION
BRM-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Body Construction (With sunroof Models)
INFOID:0000000012199837
1.
Outer side body
2.
Outer front pillar reinforcement
3.
Upper inner front pillar
4.
Lower dash
5.
Hoodledge reinforcement
6.
Lower front pillar hinge brace
7.
Weld nut
8.
Side dash
9.
Inner front pillar reinforcement
10. Upper hinge plate
11. Lower hinge plate
12. Lower front pillar bulkhead
13. Inner front pillar reinforcement
14. Front floor reinforcement
15. Front floor
JSKIA2204ZZ
Revision: November 2015
2016 JUKE
BRM-34
< REMOVAL AND INSTALLATION >
BODY CONSTRUCTION
Rear Fender Hemming Process
INFOID:0000000012199838
1. A wheel arch is to be installed and hemmed over the left and right outer wheel houses.
2. In order to hem the wheel arch, it is necessary to repair any damaged or defaced parts around outer
wheel house.
CAUTION:
Ensure that the area that is to be glued around the outer wheelhouse is undamaged or defaced.
PROCEDURE OF THE HEMMING PROCESS
• Peel off old bonding material on the surface of the outer wheel-
house and clean thoroughly.
• Peel off a primer coat in the specified area where new adhesive is
to be applied on rear fender (the replacing part).
• Apply new adhesive to both specified areas of the outer wheel-
house and rear fender.
• Attach rear fender to the body of the car, and weld the required
part except the hemming part.
• Bend the welded part starting from the center of the wheel arch
gradually with a hammer and a dolly. (Also hem the end of the
flange.)
• Hemming with a hammer is conducted to an approximate angle of
80 degrees.
• Starting from the center, hem the wheel arch gradually, using slight
back and forth motion with a hemming tool.
16. Front outrigger
17. Inner sill
18. Outer sill reinforcement
19. Nut plate
20. Inner center pillar
21. Center pillar reinforcement
22. Center pillar hinge brace
23. Inner sill reinforcement
24. Center sill reinforcement
25. Inner sill extension
26. Inner rear wheelhouse
27. Outer rear wheelhouse
28. Rear roof rail brace
29. Inner rear pillar reinforcement
30. Rear fender extension
31. Inner rear pillar
32. Inner rear wheelhouse reinforce-
ment
<Adhesive> 3M™ Automix™ Panel Bonding Adhe-
sive 08115 or equivalent
JSKIA0136GB
SIIA2245E
SIIA2246E
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст