Nissan Juke (2016 year). Service Repair Manual — part 73
BODY COMPONENT PARTS
BRM-19
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
A.
Right side
B. With sunroof models
C. Standard roof models
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
No.
Parts name
Tensile strength
(MPa)
Both sided anti-corrosive
precoated steel sections
1.
Hood
Under 440
×
2.
Inner center front bumper reinforcement
T=1.2 mm
(0.047 in)
1310
caution
—
3.
Front side member front assembly (RH & LH)
590
×
4.
Front fender (RH & LH)
Under 440
×
5.
Inner side roof rail (RH & LH)
590
—
6.
Upper inner front pillar (RH & LH)
780
—
7.
Inner center pillar (RH & LH)
590
×
8.
Side body assembly (RH & LH)
Refer to No.9
−
15
9.
Outer side roof rail reinforcement (RH & LH)
590
—
10.
Lower center pillar brace (RH & LH)
590
—
11.
Front pillar brace (RH & LH)
590
—
12.
Lower front pillar hinge brace (RH & LH)
590
—
13.
Outer front side body (RH & LH)
Under 440
×
14.
Front fender bracket assembly (RH & LH)
Under 440
×
15.
Outer sill reinforcement (RH & LH)
780
×
16.
Outer sill (RH & LH)
Under 440
×
17.
Front door (RH & LH)
Under 440
×
18.
Outer front door panel (RH & LH)
Under 440
×
19.
Rear door (RH & LH)
Under 440
×
20.
Outer rear door panel (RH & LH)
Under 440
×
21.
Inner rear pillar reinforcement (RH & LH)
440
—
22.
Rear pillar reinforcement (RH & LH)
Under 440
—
23.
Inner rear pillar (RH & LH)
Under 440
—
24.
Inner rear wheelhouse (RH & LH)
440
×
25.
Outer rear wheelhouse (RH & LH)
Under 440
×
26.
Outer rear wheelhouse extension (RH & LH)
Under 440
×
27.
Roof
Under 440
—
28.
Front roof rail
780
—
29.
Roof bow No.1
Under 440
—
30.
Roof bow No.2
590
—
31.
Roof bow No.3
Under 440
—
32.
Rear roof rail
Under 440
—
33.
Rear fender (RH & LH)
Under 440
×
34.
Rear fender extension (RH & LH)
Under 440
—
35.
Rear fender corner (RH & LH)
Under 440
×
36.
Fuel filler lid
Under 440
×
37.
Back door
Under 440
×
38.
Upper rear panel
Under 440
×
Revision: November 2015
2016 JUKE
BRM-20
< PREPARATION >
BODY COMPONENT PARTS
NOTE:
• For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
• Tensile strength column shows the largest strength value of a part in the component part.
CAUTION:
If the high strength steel (ultra high strength steel) of this is broken, replace by assembly for the supply part.
39.
Upper rear bumper retainer
Under 440
×
40.
Rear side bumper bracket
Under 440
×
41.
Rear bumper stay (RH & LH)
440
×
42.
Inner center rear bumper reinforcement
T=1.2 mm
(0.047 in)
1310
caution
—
No.
Parts name
Tensile strength
(MPa)
Both sided anti-corrosive
precoated steel sections
Revision: November 2015
2016 JUKE
CORROSION PROTECTION
BRM-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
REMOVAL AND INSTALLATION
CORROSION PROTECTION
Description
INFOID:0000000012199830
To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.
ANTI-CORROSIVE PRECOATED STEEL (GALVANNEALED STEEL)
To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet has been adopted replacing conven-
tional zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.
Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that
GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive perfor-
mance built into the vehicle at the factory.
PHOSPHATE COATING TREATMENT AND CATIONIC ELECTRODEPOSITION PRIMER
A phosphate coating treatment and a cationic electrodeposition
primer, which provide excellent corrosion protection, are employed
on all body components.
CAUTION:
Confine paint removal during welding operations to an absolute
minimum.
Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU-
INE NISSAN PARTS or an equivalent be used for panel replacement to maintain anti-corrosive performance
built into the vehicle at the factory.
Anti-corrosive Wax
INFOID:0000000012199831
To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.
DOOR
SIIA2294E
PIIA0095E
Revision: November 2015
2016 JUKE
BRM-22
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
Undercoating (2WD Models)
INFOID:0000000012199832
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust resistant, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
PRECAUTIONS IN UNDERCOATING
1. Never apply undercoating to any place unless specified (such as the areas above the muffler and three-
way catalyst that are subjected to heat).
2. Never undercoat the exhaust pipe or other parts that become hot.
3. Never undercoat rotating parts.
4. Apply bitumen wax after applying undercoating.
5. After putting seal on the vehicle, put undercoating on it.
B.
Nozzle insert hole
Unit: mm (in)
: Anti-corrosive wax coated portions
JSKIA2131ZZ
Revision: November 2015
2016 JUKE
CORROSION PROTECTION
BRM-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Undercoating (AWD Models)
INFOID:0000000012199833
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust resistant, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
PRECAUTIONS IN UNDERCOATING
1. Never apply undercoating to any place unless specified (such as the areas above the muffler and three-
way catalyst that are subjected to heat).
2. Never undercoat the exhaust pipe or other parts that become hot.
3. Never undercoat rotating parts.
4. Apply bitumen wax after applying undercoating.
5. After putting seal on the vehicle, put undercoating on it.
: Undercoated areas
: Sealed portions
JSKIA2197ZZ
Revision: November 2015
2016 JUKE
BRM-24
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
Body Sealing (2WD Models)
INFOID:0000000012199834
The following figure shows the areas that are sealed at the factory. Sealant that is applied to these areas
should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant
and not to allow other unaffected parts to come into contact with the sealant.
: Undercoated areas
: Sealed portions
JSKIA2198ZZ
Revision: November 2015
2016 JUKE
CORROSION PROTECTION
BRM-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Standard roof models
With sunroof models
: Vehicle front
: Sealed portions
JSKIA2199ZZ
Revision: November 2015
2016 JUKE
BRM-26
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
: Vehicle front
: Sealed portions
JSKIA5307ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст