Nissan Juke (2016 year). Service Repair Manual — part 364
EXL-134
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without auto light system, this item cannot be monitored.
*
2
: For models without front fog lamp, this item cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item cannot be monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
• Transmits the position light request signal to IPDM E/R via CAN communication to
turn the parking, license plate and tail lamps ON
• Transmits the position light request signal to combination meter via CAN commu-
nication to turn the position lamp indicator lamp ON
Off
Stops the position light request signal transmission
HEAD LAMP
HI
• Transmits the high beam request signal to IPDM E/R via CAN communication to
turn the headlamp (HI) ON
• Transmits the high beam request signal to combination meter via CAN communi-
cation to turn the high beam indicator lamp ON
Low
Transmits the low beam request signal to IPDM E/R via CAN communication to turn
the headlamp (LO) ON
Off
Stops the high beam request signal and low beam request signal transmission
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
EXL-135
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
1
: For models without front fog lamp and except for NISMO models with daytime running light system, this
item cannot be tested.
*
2
: For models without daytime running light system and NISMO models with daytime running light system,
this item cannot be tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (HALOGEN TYPE)
INFOID:0000000012201735
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FR FOG LAMP*
1
On
• Transmits the front fog light request signal to IPDM E/R via CAN communication
to turn the front fog lamp ON (With front fog lamp)
• Transmits the daytime running light request signal to IPDM E/R via CAN commu-
nication to turn the daytime running light ON (NISMO models with daytime running
light system)
Off
• Stops the front fog light request signal transmission (With front fog lamp)
• Stops the front fog light request signal transmission (NISMO models with daytime
running light system)
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal to IPDM E/R via CAN communi-
cation to turn the headlamp (HI) ON [Headlamp (HI) at approximately half illumina-
tion]
Off
Stops the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item cannot be tested
Off
Test item
Operation
Description
Service item
Setting item
Setting
HAZARD ANSWER BACK
Lock
Only
With locking only
Sets the hazard warning lamp answer back function when
the door is lock/unlock with the door request switch and In-
telligent Key
Unlock
Only
With unlocking only
Lock/
Unlock*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicates [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
Revision: November 2015
2016 JUKE
EXL-136
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM)
*: For models without panic alarm function, this item cannot be used.
ACTIVE TEST
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-PANIC*
[On/Off]
Indicates [On/Off] condition of PANIC button of Intelligent Key
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
• Outputs voltage to turn the right side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (RH) ON
LH
• Outputs voltage to turn the left side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (LH) ON
Off
• Stops the voltage to turn the turn signal lamps OFF
• Stops the turn indicator signal transmission
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-137
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000012962266
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch) ON
⇔
OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→
100% duty for 5 seconds
Revision: November 2015
2016 JUKE
EXL-138
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JMMIA0588GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R
and rear window defogger
• IPDM E/R
Any of the following components do not
operate
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R
and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between A/C
amp. and ECM
• CAN communication signal between ECM
and IPDM E/R
NO
• Magnet clutch
• Harness or connector between IPDM E/R
and magnet clutch
• IPDM E/R
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-139
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
CONSULT Function (IPDM E/R)
INFOID:0000000012962267
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between ECM
and IPDM E/R
NO
• Harness or connector between IPDM E/R
and cooling fan relay
• Harness or connector between IPDM E/R
and cooling fan control module.
• Harness or connector between cooling fan
control module and cooling fan motor
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via CAN
communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via CAN
communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN com-
munication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via CAN
communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN com-
munication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.
Revision: November 2015
2016 JUKE
EXL-140
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Test item
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the ignition power supply (M/T models) or shift position (CVT
models) judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN com-
munication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN com-
munication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/R.
S/L RLY -REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
S/L STATE
[LOCK/UNLK/UNKWN]
NOTE:
This item is indicated, but not monitored.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM via
CAN communication.
NOTE:
This item is monitored only for the except for NISMO models.
OIL P SW
[Open/Close]
NOTE:
This item is indicated, but not monitored.
HOOD SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM via
CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder request signal received from BCM via CAN
communication.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.
HEAD LAMP WASHER
On
NOTE:
This item is indicated, but cannot be tested.
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-141
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 second
intervals.
Fog
Operates the front fog lamp relay.
Test item
Operation
Description
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст