Nissan Juke (2016 year). Service Repair Manual — part 677
WCS-8
< SYSTEM DESCRIPTION >
SYSTEM
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram
INFOID:0000000012201467
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Illumination control
When suspending communication, changes to nighttime mode.
Shift position indicator
When suspending communication, not indicate.
Information display
Instantaneous fuel consumption
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition is
indicated.
Average fuel consumption
Possible driving distance
Torque distribution indicator
Low tire pressure warning
The display turns OFF by suspending communication.
Buzzer
The buzzer turns OFF by suspending communication.
Warning lamp/indicator lamp
ABS warning lamp
The lamp turns ON by suspending communication.
Malfunction indicator lamp
VDC warning lamp
EPS warning lamp
AWD warning lamp
Brake warning lamp
VDC OFF indicator lamp
The lamp turns OFF by suspending communication.
High beam indicator lamp
Turn signal indicator lamp
Door warning lamp
Tail lamp indicator lamp
Engine start operation indicator lamp
Shift P warning lamp
Front fog lamp indicator lamp
Oil pressure warning lamp
CRUISE indicator lamp
AWD mode indicator lamp (AWD)
AWD mode indicator lamp (AWD-V)
Key warning lamp
CVT indicator lamp
Low tire pressure warning lamp
After blinking for 1 minute, the lamp remains ON.
High coolant temperature indicator
lamp
When reception time of an abnormal signal is more than 60
seconds, the lamp turns OFF.
JSNIA2421GB
Revision: November 2015
2016 JUKE
WCS
SYSTEM
WCS-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
LIGHT REMINDER WARNING CHIME : System Description
INFOID:0000000012201468
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
Operation conditions
Ignition switch
OFF or ACC position
Combination switch (Lighting
switch)
1st or 2nd position
Driver side door
Open [front door switch (driver side) ON]
Operation conditions
Ignition switch
ON
Combination switch (Lighting
switch)
OFF or AUTO position
Driver side door
Close [front door switch (driver side) OFF]
Signal name
Signal path
Ignition switch signal
—
Combination switch signal
Combination switch (Lighting switch)
BCM
Driver door switch signal
Front door switch (driver side)
BCM
Signal name
Signal path
Buzzer output signal
BCM
Combination
meter
Revision: November 2015
2016 JUKE
WCS-10
< SYSTEM DESCRIPTION >
SYSTEM
TIMING CHART
SEAT BELT WARNING CHIME
SEAT BELT WARNING CHIME : System Diagram
INFOID:0000000012201469
SEAT BELT WARNING CHIME : System Description
INFOID:0000000012201470
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.
JSNIA2426GB
JSNIA3118GB
Operation conditions
Ignition switch
ON
Driver seat belt
Unfastened [seat belt buckle switch (driver side) ON]
Operation conditions
Ignition switch
OFF
Seat belt (driver side)
Fastened (driver side seat belt buckle switch OFF)
6 seconds after the start of warning sound
Revision: November 2015
2016 JUKE
WCS
SYSTEM
WCS-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
TIMING CHART
SOUND SPECIFICATION
PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : System Diagram
INFOID:0000000012201471
Signal name
Signal path
Ignition switch signal
—
Seat belt buckle switch signal
(driver side)
Seat belt buckle switch (driver side)
Combination meter
BCM
Signal name
Signal path
Buzzer output signal
BCM
Combination
meter
JSNIA3123GB
JSNIA3111GB
JSNIA2422GB
Revision: November 2015
2016 JUKE
WCS-12
< SYSTEM DESCRIPTION >
SYSTEM
PARKING BRAKE RELEASE WARNING CHIME : System Description
INFOID:0000000012201472
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled.
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
TIMING CHART
Operation conditions
Ignition switch
ON
Parking brake
During the operation (parking brake switch ON)
Vehicle speed
Approximately 7 km/h (4.3 MPH) or more
Operation conditions
Ignition switch
OFF
Parking brake
Release condition (parking brake switch OFF)
Vehicle speed
Approximately 3 km/h (1.9 MPH) or less
Signal name
Signal path
Ignition switch signal
—
Parking brake switch signal
Parking brake switch
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
JSNIA2428GB
Revision: November 2015
2016 JUKE
WCS
SYSTEM
WCS-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SOUND SPECIFICATION
JSNIA3640GB
Revision: November 2015
2016 JUKE
WCS-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
DIAGNOSIS SYSTEM (COMBINATION METER)
CONSULT Function
INFOID:0000000012926221
CONSULT APPLICATION ITEMS
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.
SELF DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Display Item List
X: Applicable
System
Diagnosis mode
Description
METER/M&A
Self Diagnostic Result
The combination meter checks the conditions and displays memorized errors.
Data Monitor
Displays the combination meter input/output data in real time.
Warning History
Lighting history of the warning lamp and indicator lamp can be checked.
Display item [Unit]
MAIN
SIGNALS
Description
SPEED METER
[km/h]
X
Value of vehicle speed signal received from ABS actuator and electric unit (control
unit) via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.
SPEED OUTPUT
[km/h]
X
Vehicle speed signal value transmitted to other units via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
[km/h or mph]
Odometer signal value transmitted to other units via CAN communication.
TACHO METER
[rpm]
X
• Value of the engine speed signal received from TCM via CAN communication
(CVT models).
• Value of the engine speed signal received from ECM via CAN communication
(M/T models).
NOTE:
8191.875 is displayed when the malfunction signal is received.
FUEL METER
[L]
X
Fuel level indicated on combination meter.
W TEMP METER
[
°
C]
X
Value of engine coolant temperature signal is received from ECM via CAN com-
munication.
NOTE:
215 is displayed when the malfunction signal is input.
FUEL CAP W/L
[On/Off]
Status of fuel filler cap warning display detected from fuel filler cap warning display
signal received from ECM via CAN communication.
ABS W/L
[On/Off]
Status of ABS warning lamp detected from ABS warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
VDC/TCS IND
[On/Off]
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
is received from ABS actuator and electric unit (control unit) via CAN communica-
tion.
SLIP IND
[On/Off]
Status of VDC warning lamp detected from VDC warning lamp signal received
from ABS actuator and electric unit (control unit) via CAN communication.
Revision: November 2015
2016 JUKE
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BRAKE W/L
[On/Off]
Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
NOTE:
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L
[On/Off]
Status of door open warning lamp detected from door switch signal received from
BCM via CAN communication.
HI-BEAM IND
[On/Off]
Status of high beam indicator lamp detected from high beam request signal is re-
ceived from BCM via CAN communication.
TURN IND
[On/Off]
Status of turn indicator lamp detected from turn indicator signal is received from
BCM via CAN communication.
LIGHT IND
[On/Off]
Status of tail lamp indicator lamp detected from position light request signal is re-
ceived from BCM via CAN communication.
FR FOG IND
[On/Off]
Status of front fog light indicator lamp detected from front fog light request signal
is received from BCM via CAN communication.
OIL W/L
[On/Off]
Status of oil pressure warning lamp detected from oil pressure warning lamp sig-
nal is received from ECM via CAN communication.
MIL
[On/Off]
Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.
GLOW IND
[Off]
This item is displayed, but cannot be monitored.
C-ENG2 W/L
[Off]
This item is displayed, but cannot be monitored.
CRUISE IND
[On/Off]
Status of CRUISE indicator lamp detected from ASCD status signal is received
from ECM via CAN communication.
SET IND
[Off]
This item is displayed, but cannot be monitored.
CVT IND
[On/Off]
Status of CVT indicator lamp detected from CVT status signal is received from
TCM via CAN communication.
4WD W/L
[On/Off]
Status of AWD warning lamp judged from AWD warning lamp signal received from
AWD control module with CAN communication line.
4WD LOCK IND
[On/Off]
Status of AWD mode indicator lamp (AWD-V) judged from AWD mode indicator
signal received from AWD control module with CAN communication line.
FUEL W/L
[On/Off]
Low fuel warning status detected by the identified fuel level.
AIR PRES W/L
[On/Off]
Status of low tire pressure warning lamp judged from low tire pressure warning
lamp signal received from BCM from CAN communication line.
KEY G/Y W/L
[On/Off]
Status of KEY warning lamp (G/Y) detected from KEY warning lamp signal is re-
ceived from BCM via CAN communication.
KEY KNOB W/L
[On/Off]
Status of shift P warning lamp detected from shift P warning lamp signal is re-
ceived from BCM via CAN communication.
EPS W/L
[On/Off]
Status of EPS warning lamp detected from EPS warning lamp signal is received
from EPS control unit via CAN communication.
DPF W/L
[Off]
This item is displayed, but cannot be monitored.
LCD
[B&P N, B&P I, SFT P, BATT, NO KY,
LK WN]
*1
[C&P N, C&P I, SFT P, BATT, NO KY,
LK WN]
*2
Status of engine start operation indicator lamp, shift P warning lamp and KEY
warning lamp, detected from engine start operation indicator lamp signal, shift P
warning lamp signal and KEY warning lamp signal are received from BCM via
CAN communication.
SHIFT IND
[P, R, N, D, M1, M2, M3,
M4, M5, M6, M7, M8]
Status of shift position indicator judged from shift position signal received from
TCM with CAN communication line.
Display item [Unit]
MAIN
SIGNALS
Description
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст