Nissan Juke (2016 year). Service Repair Manual — part 693
WASHER TANK
WW-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REMOVAL AND INSTALLATION
WASHER TANK
Exploded View
INFOID:0000000012197069
Removal and Installation
INFOID:0000000012197070
REMOVAL
1. Fully open hood.
2. Remove washer tank inlet fixing clip (A).
3. Pull out washer tank inlet (1) from washer tank.
4. Remove fender protector RH (front). Refer to
EXT-31, "Removal and Installation"
5. Disconnect washer pump connector.
6. Disconnect washer level switch connector (Canada models only).
7. Disconnect front washer tube and rear washer tube.
8. Remove washer tank mounting bolts.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
1.
Washer tank inlet cap
2.
Washer tank inlet
3.
Front washer tube
4.
Washer pump
5.
Rear washer tube
6.
Packing
7.
Washer tank
8.
Washer tank (Canada models only)
9.
Washer level sensor (Canada mod-
els only)
A
: Clip
: Vehicle front
: N·m (kg·m, in-lb)
JMLIA1731GB
: Vehicle front
JMLIA1158ZZ
Revision: November 2015
2016 JUKE
WW-44
< REMOVAL AND INSTALLATION >
WASHER TANK
CAUTION:
Add water up to the top of washer tank inlet after installing and check that there is no leakage.
Revision: November 2015
2016 JUKE
WASHER PUMP
WW-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER PUMP
Exploded View
INFOID:0000000012197071
Removal and Installation
INFOID:0000000012197072
REMOVAL
1. Remove fender protector RH (front). Refer to
EXT-31, "Removal and Installation"
2. Disconnect washer pump connector.
3. Disconnect front washer tube and rear washer tube.
4. Remove washer pump from the washer tank.
5. Remove packing from washer tank.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check that there is no leakage after installation or replace packing with new part if it has been dam-
age.
• Never twist the packing when installing the washer pump.
1.
Washer tank inlet cap
2.
Washer tank inlet
3.
Front washer tube
4.
Washer pump
5.
Rear washer tube
6.
Packing
7.
Washer tank
8.
Washer tank (Canada models only)
9.
Washer level sensor (Canada mod-
els only)
A
: Clip
: Vehicle front
: N·m (kg·m, in-lb)
JMLIA1731GB
Revision: November 2015
2016 JUKE
WW-46
< REMOVAL AND INSTALLATION >
WASHER LEVEL SWITCH
WASHER LEVEL SWITCH
Removal and Installation
INFOID:0000000012197073
The washer level switch must be replaced together with the washer tank as an assembly. Refer to
.
Revision: November 2015
2016 JUKE
FRONT WASHER NOZZLE AND TUBE
WW-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WASHER NOZZLE AND TUBE
Exploded View
INFOID:0000000012197074
Hydraulic Layout
INFOID:0000000012197075
Removal and Installation
INFOID:0000000012197076
REMOVAL
1. Remove cowl top cover. Refer to
EXT-30, "Removal and Installation"
.
2. Disconnect front washer tube from front washer nozzle.
1.
Front washer nozzle LH
2.
Front washer nozzle RH
3.
Cowl top cover
4.
Front washer tube (tank side)
5.
Front washer tube RH
6.
Front washer tube LH
: Vehicle front
JMLIA1385ZZ
1.
Front washer nozzle
2.
Check valve
3.
Front washer tube
4.
Washer tank
: Clip
JMLIA1161ZZ
Revision: November 2015
2016 JUKE
WW-48
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
3. While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000012197077
INSPECTION
Check valve Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle (1)), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
JPLIA0871ZZ
JMLIA1326ZZ
1.
Black printed frame line
: Spray area
: Target spray position
JMLIA1497ZZ
Revision: November 2015
2016 JUKE
FRONT WASHER NOZZLE AND TUBE
WW-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
Spray position
H
L
X
Y
S
A
244 (9.61)
350 (13.78)
80 (3.15)
238 (9.37)
78 (3.07)
B
284 (11.18)
93 (3.66)
80 (3.15)
257 (10.12)
89 (3.50)
C
258 (10.16)
70.5 (2.78)
80 (3.15)
255 (10.04)
82 (3.23)
D
309 (12.17)
234 (9.21)
80 (3.15)
312 (12.28)
95 (3.74)
E
235 (9.25)
413 (16.26)
80 (3.15)
295 (11.61)
90 (3.54)
JPLIA0873ZZ
Revision: November 2015
2016 JUKE
WW-50
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000012197078
Removal and Installation
INFOID:0000000012197079
REMOVAL
1. Operate front wiper to move it to the auto stop position.
2. Open the hood.
3. Disengage front wiper arm cap (1) fixing pawls with a remover
tool (A), and then remove front wiper arm cap from the wiper
arm (2).
4. Remove front wiper arm mounting nuts.
5. Raise front wiper arm, and then remove front wiper arm from the vehicle.
INSTALLATION
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper arm RH
5.
Front wiper blade RH
6.
Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1732GB
: Pawl
: Vehicle front
JMLIA1164ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст