Nissan Juke (2016 year). Service Repair Manual — part 694
FRONT WIPER ARM
WW-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Operate front wiper motor to move the front wiper to the auto
stop position.
3. Adjust front wiper blade position. Refer to
4. Install front wiper arm by tightening the mounting nuts.
5. Inject the washer fluid.
6. Operate front wiper to move it to the auto stop position.
7. Check that the front wiper blades stop at the specified position.
8. Install front wiper arm caps.
Adjustment
INFOID:0000000012197080
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover/ front fender protector and the top of wiper blade center
Standard clearance
ELH0717D
1.
Front wiper arm LH
2.
Front wiper arm RH
3.
Cowl top cover
4.
Front fender cover
5.
Windshield glass assembly
JMLIA1334ZZ
R
: 37.7
±
7.5 mm (1.484
±
0.295 in)
L
: 46.8
±
7.5 mm (1.843
±
0.295 in)
Revision: November 2015
2016 JUKE
WW-52
< REMOVAL AND INSTALLATION >
FRONT WIPER BLADE
FRONT WIPER BLADE
Exploded View
INFOID:0000000012197081
Removal and Installation
INFOID:0000000012197082
REMOVAL
Push up the lever (A) of wiper blade (1), while sliding wiper blade
toward the direction of the arrow to remove it from wiper arm (2).
CAUTION:
Be careful not to drop the wiper blade onto the windshield
glass.
INSTALLATION
1. Install wiper blade into wiper arm.
2. Install wiper arm.
Replacement
INFOID:0000000012197083
1. Remove the wiper blade from the wiper arm. Refer to
WW-52, "Removal and Installation"
.
1.
Wiper arm
2.
Wiper blade
3.
Wiper refill
A
: Wiper refill end
B:
: Wiper refill tip
: Always replace after every disassembly.
JMLIA1733ZZ
JMLIA1166ZZ
Revision: November 2015
2016 JUKE
FRONT WIPER BLADE
WW-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2. Pinch the vertebra with tenailles (A) and slide the wiper refill (2)
toward the direction of the arrow 2 to remove.
NOTE:
Be careful not to damage the wiper blade (1).
3. Insert the new wiper refill kit (2) as shown in the figure to the wiper blade (1) until the stopper at the wiper
refill end fits into the tab on wiper blade.
NOTE:
• Insert the wiper refill to be held securely by tab of wiper blade.
• After the wiper refill is fully inserted, remove the holder (A).
• The refill kit is provided as a set attached to service parts.
4. After installing the new wiper refill (1) check that the vertebra (2) is well inserted into the wiper refill (1).
NOTE:
Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab (B) on wiper blade.
• Wiper refill is inserted from the proper direction.
• The stopper (A) is inserted into the wiper refill.
JMLIA1737ZZ
JMLIA1738ZZ
JMLIA1734ZZ
Revision: November 2015
2016 JUKE
WW-54
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000012197084
REMOVAL
DISASSEMBLY
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper arm RH
5.
Front wiper blade RH
6.
Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1732GB
1.
Front wiper linkage 1
2.
Shaft seal
3.
Front wiper frame
4.
Front wiper motor
5.
Front wiper linkage 2
: Nissan MP special grease No.2
JMLIA1498ZZ
Revision: November 2015
2016 JUKE
FRONT WIPER DRIVE ASSEMBLY
WW-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Removal and Installation
INFOID:0000000012197085
REMOVAL
1. Remove front wiper arms (LH and RH). Refer to
WW-50, "Removal and Installation"
.
2. Remove cowl top cover. Refer to
EXT-30, "Removal and Installation"
.
3. Disconnect the front wiper motor connector.
4. Remove the mounting bolts from front wiper drive assembly.
5. Remove the front wiper drive assembly from the vehicle.
INSTALLATION
1. Install the front wiper drive assembly to the vehicle.
2. Connect front wiper motor connector.
3. Operate front wiper to move it to the auto stop position.
4. Install cowl top cover. Refer to
EXT-30, "Removal and Installation"
.
5. Install front wiper arms. Refer to
WW-50, "Removal and Installation"
.
Disassembly and Assembly
INFOID:0000000012197086
DISASSEMBLY
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position.
3. Disconnect the front wiper motor connector.
4. Install the front wiper motor to the front wiper frame.
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply Multi
−
purpose grease or an equivalent if necessary.
Revision: November 2015
2016 JUKE
WW-56
< REMOVAL AND INSTALLATION >
WIPER AND WASHER SWITCH
WIPER AND WASHER SWITCH
Exploded View
INFOID:0000000012197087
Wiper and washer switch is integrated in the combination switch. Refer to
Revision: November 2015
2016 JUKE
REAR WIPER ARM
WW-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER ARM
Exploded View
INFOID:0000000012197088
Removal and Installation
INFOID:0000000012197089
REMOVAL
1. Operate rear wiper to the auto stop position.
2. Remove rear wiper arm cover.
3. Remove rear wiper arm mounting nut.
4. Remove wiper arm from the vehicle.
INSTALLATION
1. Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
2. Operate the rear wiper motor to the auto stop position.
3. Adjust the rear wiper blade position. Refer to
.
4. Install the rear wiper arm by tightening the mounting nut.
5. Inject the washer fluid.
6. Operate the rear wiper to the auto stop position.
7. Check that the rear wiper blades stop at the specified position.
8. Install the rear wiper arm cover.
Adjustment
INFOID:0000000012197090
REAR WIPER BLADE POSITION ADJUSTMENT
1.
Rear wiper motor
2.
Rear wiper blade
3.
Rear wiper arm
4.
Rear wiper arm cover
5.
Rear wiper pivot seal
A
: Canada models only
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1503GB
SKIA0082J
Revision: November 2015
2016 JUKE
WW-58
< REMOVAL AND INSTALLATION >
REAR WIPER ARM
Set the wiper blade top on the defrosting wire (A) (clearance between the end of back door glass and the top
of wiper blade center).
Standard clearance
1. Rear wiper blade
2. Back door window glass
3. Back door panel
A : Rear defogger wire print
L
: 67.5
±
7.5 mm (2.657
±
0.295in)
JMLIA1170ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст