Nissan Juke (2016 year). Service Repair Manual — part 692
WASHER SWITCH
WW-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER SWITCH
Component Inspection
INFOID:0000000012197060
1.
CHECK WASHER SWITCH
1. Turn ignition switch OFF.
2. Disconnect combination switch connector.
3. Check continuity between the combination switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination switch (Wiper and washer switch).
A
: Terminal 4
B
: Terminal 6
C
: Terminal 3
D
: Terminal 1
JPLIA0164GB
Combination switch
Condition
Continuity
Terminal
3
4
Front washer switch ON
Existed
1
6
1
4
Rear washer switch ON
6
3
Revision: November 2015
2016 JUKE
WW-36
< DTC/CIRCUIT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
REAR WIPER MOTOR CIRCUIT
Component Function Check
INFOID:0000000012197061
1.
CHECK REAR WIPER ON OPERATION
CONSULT ACTIVE TEST
1. Select “RR WIPER” of BCM active test item.
2. With operating the test item, check rear wiper operation.
Is rear wiper operation normally?
YES
>> Rear wiper motor circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197062
1.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn rear wiper switch OFF, and wait for 1 minute or more.
2. Turn ignition switch OFF.
3. Disconnect rear wiper motor connector.
4. Turn ignition switch ON.
5. Select “RR WIPER” of BCM active test item.
6. With operating the test item, check voltage between rear wiper motor harness connector and ground.
*: When “REAR WIPER” is “On” for 5 seconds or more during active test of CONSULT, BCM stops the power
supply according to rear wiper motor protection function. To perform the check again, turn “REAR WIPER” to
“Off”, wait for 1 minute or more, and then perform the check.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR WIPER MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear wiper motor harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
On
: Rear wiper ON operation
Off
: Stop the rear wiper.
(+)
(
−
)
Condition
Voltage (Approx.)
Rear wiper motor
Connector
Terminal
D112
1
Ground
REAR WIPER
On
Battery voltage
(5 seconds*)
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
B10
54
D112
1
Existed
BCM
Ground
Continuity
Connector
Terminal
B10
54
Not existed
Revision: November 2015
2016 JUKE
REAR WIPER MOTOR CIRCUIT
WW-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
3.
CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT
Check continuity between rear wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear wiper motor.
NO
>> Repair or replace harness.
Rear wiper motor
Ground
Continuity
Connector
Terminal
D112
3
Existed
Revision: November 2015
2016 JUKE
WW-38
< DTC/CIRCUIT DIAGNOSIS >
REAR WIPER STOP POSITION SIGNAL CIRCUIT
REAR WIPER STOP POSITION SIGNAL CIRCUIT
Component Function Check
INFOID:0000000012197063
1.
CHECK REAR WIPER STOP POSITION SIGNAL
CONSULT DATA MONITOR
1. Select “WIPER” of BCM data monitor item.
2. Operate the rear wiper.
3. Check that “RR WIPER STOP” changes to “On” and “Off” linked with the wiper operation.
Is the status of item normal?
YES
>> Rear wiper stop position signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197064
1.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect rear wiper motor connector.
3. Turn ignition switch ON.
4. Check voltage between rear wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear wiper motor.
NO
>> GO TO 2.
2.
CHECK REAR WIPER MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear wiper motor harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
Monitor item
Condition
Monitor status
RR WIPER STOP
Rear wiper motor
Stop position
On
Except stop position
Off
(+)
(
−
)
Voltage (Approx.)
Rear wiper motor
Connector
Terminal
D112
2
Ground
Battery voltage
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
B10
44
D112
2
Existed
BCM
Ground
Continuity
Connector
Terminal
B10
44
Not existed
Revision: November 2015
2016 JUKE
WIPER AND WASHER SYSTEM SYMPTOMS
WW-39
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000012197065
Symptom
Probable malfunction location
Inspection item
Front wiper does not
operate
HI only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
.
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (HI) circuit
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
LO and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
.
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (LO) circuit
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
HI, LO and INT
SYMPTOM DIAGNOSIS
Refer to
Front wiper does not
stop
HI only
• Combination switch
• BCM
Combination switch
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
IPDM E/R
—
LO only
• Combination switch
• BCM
Combination switch
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
IPDM E/R
—
INT only
• Combination switch
• BCM
Combination switch
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “FR WIP REQ”
Revision: November 2015
2016 JUKE
WW-40
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front wiper does not
operate normally
Intermittent adjust-
ment cannot be per-
formed
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed
Check the wiper setting is linked with vehicle speed.
Refer to
WW-14, "WIPER : CONSULT Function - WIPER"
Service positioning
operation does not
operate
• Combination switch
• BCM
• IPDM E/R
.
Wiper is not linked to
the washer operation
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Does not return to
stop position [Re-
peatedly operates for
10 seconds and then
stops for 20 seconds.
After that, it stops the
operation. (Fail-
safe)]
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper stop position sig-
nal circuit
Refer to
Rear wiper does not
operate
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
.
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
Rear wiper motor circuit
Refer to
Rear wiper does not
stop
ON only
• Combination switch
• BCM
.
INT only
• Combination switch
• BCM
.
Rear wiper does not
operate normally
Wiper is not linked to
the washer operation
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
.
BCM
—
Rear wiper does not
return to the stop po-
sition. [Stops after a
five-second opera-
tion. (Fail-safe)]
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper stop position sig-
nal circuit
Refer to
Symptom
Probable malfunction location
Inspection item
Revision: November 2015
2016 JUKE
NORMAL OPERATING CONDITION
WW-41
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000012197066
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
Revision: November 2015
2016 JUKE
WW-42
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000012197067
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000012197068
1.
CHECK WIPER RELAY OPERATION
CONSULT ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
Check front wiper motor fuse. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse after repairing the applicable circuit.
3.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
Check front wiper motor ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the status of “FR WIP REQ”.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 5.
5.
CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace the applicable parts.
Lo
: Front wiper LO operation
Hi
: Front wiper HI operation
Off
: Stop the front wiper.
Monitor item
Condition
Monitor status
FR WIP REQ
Front wiper switch HI
On
Hi
Off
Stop
Front wiper switch LO
On
Low
Off
Stop
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст