Nissan Juke (2016 year). Service Repair Manual — part 347
EX-10
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
AWD (NISMO RS models)
Removal and Installation
INFOID:0000000012197615
REMOVAL
• Disconnect each joint and mounting.
• Remove heated oxygen sensor 2 with following procedure (2WD models):
- Using heated oxygen sensor wrench [SST: KV10114400 (J-
38365)] (A), removal heated oxygen sensor 2 (1).
CAUTION:
• Never damage heated oxygen sensor 2.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Always replace seal bearings with new ones when reassembling.
JSBIA5992GB
1.
Center tube
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Seal bearing
8.
Ring gasket
9.
Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
PBIC4498J
Revision: November 2015
2016 JUKE
EXHAUST SYSTEM
EX-11
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
• Discard any heated oxygen sensor 2 which has been dropped onto a hard surface such as a con-
crete floor. Use a new one.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner [commercial service tool: J-43897-18 or J-43897-12] and apply anti-seize
lubricant (commercial service tool).
• Never over torque heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
• Prevent rust preventives from adhering to the sensor body.
• If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, remove them.
• When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid gas
leakage.
• When installing each mounting rubber, use silicon oil to avoid twisting.
• Temporarily tighten mounting nuts and bolts. Check each part for unusual interference and mount-
ing rubber interference, and then tighten them to the specified torque.
• When installing each mounting rubber, avoid twisting or unusual extension in up/down, front/rear
and right/left directions.
• Install seal bearing according to the following instructions.
CAUTION:
The structure of seal bearing depends on the mounting por-
tion. When installing seal bearings, be careful not to install
wrong one.
Exhaust Manifold to Exhaust Front Tube
1. Place a piece of wood (A) on seal bearing (2) and securely
insert the seal bearing on the exhaust manifold (1) side, using a
plastic hammer (B).
CAUTION:
• Never damage the seal bearing surface during insertion.
• If seal bearing is inserted by hammering directly without
using a piece of wood, the seal bearing is deformed and
exhaust gas leaks. To insert seal bearing, always use a
piece of wood and insert straight.
: Exhaust manifold side
: Mesh
: Exhaust front tube side
: Pawl (projection)
JPBIA6287ZZ
JPBIA6288ZZ
Revision: November 2015
2016 JUKE
EX-12
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
2. Check that seal bearing (1) is in absolute contact (C) with the
flange (A). If there is clearance (B), insert seal bearing straight
by hand to bring the seal bearing into absolute contact with the
flange.
CAUTION:
• Never use a tool for insertion.
• Never insert seal bearing by tightening exhaust front
tube.
3. With spring (3), tighten nut (4).
CAUTION:
• Fasten stud bolts to the flange of exhaust manifold side to
the specified torque before fastening mounting nuts.
• Ensure springs are seated correctly on the flange and not
sitting on (A).
• Be careful that stud bolt does not interfere with mounting hole of exhaust front tube (
).
4. After installing, check that stud bolt does not interfere with mounting hole of exhaust front tube.
Exhaust Front Tube to Main Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction as shown in the figure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring, tighten bolt.
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that bolt does not interfere with mounting hole of main muffler (
).
3. After installing, check that bolt does not interfere with mounting hole of main muffler.
Inspection
INFOID:0000000012197616
INSPECTION AFTER INSTALLATION
• Check clearance between tail tube and rear bumper is even.
• With engine running, check exhaust tube joints for gas leakage and unusual noises.
• Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
JPBIA6289ZZ
1
: Exhaust manifold
2
: Seal bearing
5
: Stud bolt
6
: Exhaust front tube
JPBIA2372ZZ
3
: Spring
4
: Bolt
5
: Main muffler
JPBIA2174ZZ
Revision: November 2015
2016 JUKE
EXL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
EXL
A
B
EXL
N
O
P
CONTENTS
EXTERIOR LIGHTING SYSTEM
XENON TYPE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precautions For Xenon Headlamp Service . . . ...
Precautions for Removing Battery Terminal . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
EXTERIOR LIGHTING SYSTEM . . . . . . . .....
EXTERIOR LIGHTING SYSTEM : Component
Parts Location . . . . . . . . . . . . . . ...
EXTERIOR LIGHTING SYSTEM :
Component Description . . . . . . . . . . ....
HEADLAMP ASSEMBLY . . . . . . . . . . ....
HEADLAMP ASSEMBLY : Xenon Headlamp . . ...
HEADLAMP ASSEMBLY : HID control unit . . .
SYSTEM . . . . . . . . . . . . . . . .
HEADLAMP SYSTEM . . . . . . . . . . . ...
HEADLAMP SYSTEM : System Diagram . . . ...
HEADLAMP SYSTEM : System Description . . ...
HEADLAMP SYSTEM : Fail-Safe . . . . . . ...
AUTO LIGHT SYSTEM . . . . . . . . . . . .
AUTO LIGHT SYSTEM : System Diagram . . . .
AUTO LIGHT SYSTEM : System Description . . .
DAYTIME RUNNING LIGHT SYSTEM . . . . . ..
DAYTIME RUNNING LIGHT SYSTEM : System
Diagram . . . . . . . . . . . . . . . . ...
DAYTIME RUNNING LIGHT SYSTEM : System
Description . . . . . . . . . . . . . . . ..
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM . . . . . . . . . . . . . . . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram . . . . . . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description . . . . . . . .
PARKING, LICENSE PLATE, SIDE MARKER AND
TAIL LAMP SYSTEM . . . . . . . . . . . . .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Diagram . .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Description .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : Fail-Safe . . . . .
FRONT FOG LAMP SYSTEM . . . . . . . . ...
FRONT FOG LAMP SYSTEM : System Diagram .
FRONT FOG LAMP SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ...
FRONT FOG LAMP SYSTEM : Fail-Safe . . . ...
EXTERIOR LAMP BATTERY SAVER SYSTEM . ...
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Diagram . . . . . . . . . . . . . ..
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Description . . . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) (XENON TYPE) . . . . . . . . . . ...
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT Function (BCM - FLASH-
ER) (XENON TYPE) . . . . . . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . ...
Revision: November 2015
2016 JUKE
EXL-2
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . ....
ECU DIAGNOSIS INFORMATION . . . ..
BCM, IPDM E/R . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . .
EXTERIOR LIGHTING SYSTEM . . . . . ...
Wiring Diagram . . . . . . . . . . . . . ...
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . .
Work Flow . . . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
HEADLAMP (HI) CIRCUIT . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
HEADLAMP (LO) CIRCUIT . . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
XENON HEADLAMP . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ..
PARKING LAMP CIRCUIT . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
FRONT SIDE MARKER LAMP CIRCUIT . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
TAIL LAMP CIRCUIT . . . . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
LICENSE PLATE LAMP CIRCUIT . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
DAYTIME RUNNING LIGHT RELAY CIRCUIT
...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
DAYTIME RUNNING LIGHT CIRCUIT . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
FRONT FOG LAMP CIRCUIT . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
TURN SIGNAL LAMP CIRCUIT . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
OPTICAL SENSOR . . . . . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . .
EXTERIOR LIGHTING SYSTEM SYMPTOMS ...
Symptom Table . . . . . . . . . . . . . ...
NORMAL OPERATING CONDITION . . . .
Description . . . . . . . . . . . . . . . ..
BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
BOTH SIDE HEADLAMPS (LO) ARE NOT
TURNED ON . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMPS ARE NOT TURNED ON . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
PERIODIC MAINTENANCE . . . . . ...
HEADLAMP AIMING ADJUSTMENT . . . ...
Description . . . . . . . . . . . . . . . ..
Aiming Adjustment Procedure . . . . . . . .
FRONT FOG LAMP AIMING ADJUSTMENT ...
Description . . . . . . . . . . . . . . . ..
Aiming Adjustment Procedure . . . . . . . .
REMOVAL AND INSTALLATION . . . ..
HEADLAMP . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . .
FRONT COMBINATION LAMP . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . ..
Revision: November 2015
2016 JUKE
EXL-3
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DAYTIME RUNNING LIGHT . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
FRONT FOG LAMP . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
SIDE TURN SIGNAL LAMP . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
OPTICAL SENSOR . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
LIGHTING & TURN SIGNAL SWITCH . . .
Removal and Installation . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR COMBINATION LAMP . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
HIGH-MOUNTED STOP LAMP . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
LICENSE PLATE LAMP . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
REAR FOG LAMP . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR REFLEX REFLECTOR . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
Bulb Specifications . . . . . . . . . . . .
HALOGEN TYPE
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . .
Precaution for Procedure without Cowl Top Cover ..
Precautions for Removing Battery Terminal . . ..
SYSTEM DESCRIPTION . . . . . . ...
COMPONENT PARTS . . . . . . . . .
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . .
SYSTEM . . . . . . . . . . . . . . ..
HEADLAMP SYSTEM . . . . . . . . . . . .
HEADLAMP SYSTEM : System Diagram . . . .
HEADLAMP SYSTEM : System Description . . .
HEADLAMP SYSTEM : Fail-Safe . . . . . . ..
AUTO LIGHT SYSTEM . . . . . . . . . . .
AUTO LIGHT SYSTEM : System Diagram . . .
AUTO LIGHT SYSTEM : System Description . ...
DAYTIME RUNNING LIGHT SYSTEM . . . . .
DAYTIME RUNNING LIGHT SYSTEM : System
Diagram . . . . . . . . . . . . . . . . .
DAYTIME RUNNING LIGHT SYSTEM : System
Description . . . . . . . . . . . . . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM . . . . . . . . . . . . . . . . ...
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram . . . . . . . . ..
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description . . . . . . . ..
PARKING, LICENSE PLATE, SIDE MARKER AND
TAIL LAMP SYSTEM . . . . . . . . . . . ...
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Diagram . ..
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Description ..
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : Fail-Safe . . . . ..
FRONT FOG LAMP SYSTEM . . . . . . . . .
FRONT FOG LAMP SYSTEM : System Diagram ..
FRONT FOG LAMP SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . .
FRONT FOG LAMP SYSTEM : Fail-Safe . . . .
EXTERIOR LAMP BATTERY SAVER SYSTEM . .
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Diagram . . . . . . . . . . . . .
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Description . . . . . . . . . . . .
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . ...
HEADLAMP . . . . . . . . . . . . . . . .
HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) (HALOGEN TYPE) . . . . . . . . .
Revision: November 2015
2016 JUKE
EXL-4
FLASHER . . . . . . . . . . . . . . . . .
FLASHER : CONSULT Function (BCM - FLASH-
ER) (HALOGEN TYPE) . . . . . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . ..
Diagnosis Description . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . .
BCM, IPDM E/R . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . .
EXTERIOR LIGHTING SYSTEM . . . . . .
Wiring Diagram . . . . . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . ..
DIAGNOSIS AND REPAIR WORK FLOW . ..
Work Flow . . . . . . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . .
HEADLAMP (HI) CIRCUIT . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
HEADLAMP (LO) CIRCUIT . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
PARKING LAMP CIRCUIT . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
FRONT SIDE MARKER LAMP CIRCUIT . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
TAIL LAMP CIRCUIT . . . . . . . . . ...
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
LICENSE PLATE LAMP CIRCUIT . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
DAYTIME RUNNING LIGHT RELAY CIRCUIT
.
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
DAYTIME RUNNING LIGHT CIRCUIT . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
FRONT FOG LAMP CIRCUIT . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
TURN SIGNAL LAMP CIRCUIT . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
OPTICAL SENSOR . . . . . . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
HAZARD SWITCH . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . ...
EXTERIOR LIGHTING SYSTEM SYMPTOMS ..
Symptom Table . . . . . . . . . . . . . .
NORMAL OPERATING CONDITION . . . ...
Description . . . . . . . . . . . . . . .
BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
BOTH SIDE HEADLAMPS (LO) ARE NOT
TURNED ON . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMPS ARE NOT TURNED ON .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ..
HEADLAMP AIMING ADJUSTMENT . . . ..
Description . . . . . . . . . . . . . . .
Aiming Adjustment Procedure . . . . . . . ..
FRONT FOG LAMP AIMING ADJUSTMENT ..
Description . . . . . . . . . . . . . . .
Aiming Adjustment Procedure . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
HEADLAMP . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . ..
FRONT COMBINATION LAMP . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
Revision: November 2015
2016 JUKE
EXL-5
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Disassembly and Assembly . . . . . . . . ..
DAYTIME RUNNING LIGHT . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
FRONT FOG LAMP . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
SIDE TURN SIGNAL LAMP . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
OPTICAL SENSOR . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
LIGHTING & TURN SIGNAL SWITCH . . .
Removal and Installation . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR COMBINATION LAMP . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
HIGH-MOUNTED STOP LAMP . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
LICENSE PLATE LAMP . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
REAR FOG LAMP . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
REAR REFLEX REFLECTOR . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
Bulb Specifications . . . . . . . . . . . .
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст