Nissan Juke (2016 year). Service Repair Manual — part 346
EX-2
< PRECAUTION >
[MR16DDT ]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal
INFOID:0000000012197609
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Removal and Installation
INFOID:0000000012197610
CAUTION:
• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
• Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
• Be careful not to cut your hand on the heat insulator edge.
SEF289H
Revision: November 2015
2016 JUKE
PREPARATION
EX-3
< PREPARATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000012197611
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000012197612
Tool number
(TechMate No.)
Tool name
Description
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 2 ( 2WD models)
a: For 22 mm (0.87 in) width hexagon nut
S-NT636
Tool name
Description
Power tool
Loosening nuts and bolts
Heated oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating heated oxygen sensor thread
cleaner when reconditioning exhaust system
threads
PBIC0190E
JPBIA0238ZZ
AEM489
Revision: November 2015
2016 JUKE
EX-4
< PERIODIC MAINTENANCE >
[MR16DDT ]
EXHAUST SYSTEM
PERIODIC MAINTENANCE
EXHAUST SYSTEM
Inspection
INFOID:0000000012197613
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
SMA211A
Revision: November 2015
2016 JUKE
EXHAUST SYSTEM
EX-5
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000012197614
2WD (Standard models)
JSBIA3454GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Heated oxygen sensor 2
8.
Seal bearing
9.
Ring gasket
10. Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: November 2015
2016 JUKE
EX-6
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
2WD (NISMO models)
JPBIA7035GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Heated oxygen sensor 2
8.
Seal bearing
9.
Ring gasket
10. Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: November 2015
2016 JUKE
EXHAUST SYSTEM
EX-7
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
2WD (NISMO RS models)
JSBIA4459GB
1.
Center tube
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Heated oxygen sensor 2
8.
Seal bearing
9.
Ring gasket
10. Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: November 2015
2016 JUKE
EX-8
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
AWD (Standard models)
JSBIA3455GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Seal bearing
8.
Ring gasket
9.
Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: November 2015
2016 JUKE
EXHAUST SYSTEM
EX-9
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
AWD (NISMO models)
JSBIA3379GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Seal bearing
8.
Ring gasket
9.
Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст