Nissan Juke (2016 year). Service Repair Manual — part 535
POWER WINDOW MOTOR
PWC-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW MOTOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000012196924
1.
CHECK FUNCTION
Check front power window motor (driver side) operation with power window main switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-35, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000012196925
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor (driver side) connector.
3. Turn ignition switch ON.
4. Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side). Refer to
GW-20, "Disassembly and Assembly"
.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between front power window motor (driver side) harness connector and power window
main switch harness connector.
4. Check continuity between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
NO
>> Repair or replace harness.
PASSENGER SIDE
(+)
(-)
Condition
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D37
2
Ground
Power window main
switch
(driver side switch)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window motor (driver side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D37
2
D35
17
Existed
3
19
Front power window motor (driver side)
Ground
Continuity
Connector
Terminal
D37
2
Not existed
3
Revision: November 2015
2016 JUKE
PWC-36
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
PASSENGER SIDE : Component Function Check
INFOID:0000000012196926
1.
CHECK FUNCTION
heck front power window motor (passenger side) operation with front power window switch (passenger side)
or power window main switch (passenger side switch).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-36, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000012196927
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor (passenger side) connector.
3. Turn ignition switch ON.
4. Check voltage between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (passenger side). Refer to
GW-20, "Disassembly and Assem-
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window switch (passenger side) connector.
3. Check continuity between front power window motor (passenger side) harness connector and front power
window switch (passenger side) harness connector.
4. Check continuity between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-54, "Removal and Installa-
.
NO
>> Repair or replace harness.
REAR LH
(+)
(-)
Condition
Voltage (V)
Front power window motor (passenger side)
Connector
Terminal
D16
1
Ground
Front power window
switch
(passenger side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window motor (passenger side)
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D16
1
D10
5
Existed
3
4
Front power window motor (passenger side)
Ground
Continuity
Connector
Terminal
D16
1
Not existed
3
Revision: November 2015
2016 JUKE
POWER WINDOW MOTOR
PWC-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR LH : Component Function Check
INFOID:0000000012196928
1.
CHECK FUNCTION
Check rear power window motor LH operation with rear power window switch LH or power window main
switch (rear LH switch).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-37, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000012196929
1.
CHECK REAR POWER WINDOW MOTOR LH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor LH connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window motor LH. Refer to
GW-23, "Disassembly and Assembly"
.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR LH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH connector.
3. Check continuity between rear power window motor LH harness connector and rear power window switch
LH harness connector.
4. Check continuity between rear power window motor LH connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch LH. Refer to
PWC-54, "Removal and Installation"
.
NO
>> Repair or replace harness.
REAR RH
REAR RH : Component Function Check
INFOID:0000000012196930
1.
CHECK FUNCTION
(+)
(-)
Condition
Voltage (V)
Rear power window motor LH
Connector
Terminal
D67
1
Ground
Rear power win-
dow switch LH
NEUTRAL
0 – 1
DOWN
9 – 16
3
NEUTRAL
0 – 1
UP
9 – 16
Rear power window motor LH
Rear power window switch LH
Continuity
Connector
Terminal
Connector
Terminal
D67
1
D63
4
Existed
3
5
Rear power window motor LH
Ground
Continuity
Connector
Terminal
D67
1
Not existed
3
Revision: November 2015
2016 JUKE
PWC-38
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
Check rear power window motor RH operation with rear power window switch RH and power window main
switch (rear RH switch).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-38, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000012196931
1.
CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor RH connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window motor RH. Refer to
GW-23, "Disassembly and Assembly"
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH connector.
3. Check continuity between rear power window motor RH harness connector and rear power window switch
RH harness connector.
4. Check continuity between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch RH. Refer to
PWC-54, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(-)
Condition
Voltage (V)
Rear power window motor RH
Connector
Terminal
D47
1
Ground
Rear power window
switch RH
NEUTRAL
0 – 1
DOWN
9 – 16
3
NEUTRAL
0 – 1
UP
9 – 16
Rear power window motor RH
Rear power window switch RH
Continuity
Connector
Terminal
Connector
Terminal
D47
1
D43
4
Existed
3
5
Rear power window motor RH
Ground
Continuity
Connector
Terminal
D47
1
Not existed
3
Revision: November 2015
2016 JUKE
ENCODER CIRCUIT
PWC-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ENCODER CIRCUIT
Component Function Check
INFOID:0000000012196932
1.
CHECK FUNCTION
Check that front driver side door glass perform AUTO UP/DOWN operation normally when power window
main switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196933
1.
CHECK ENCODER PULSE SIGNAL
1. Turn ignition switch ON.
2. Check signal between power window main switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK ENCODER SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector and front power window motor (driver side) connector.
3. Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4. Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
(+)
(-)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D35
4
Ground
Refer to the following signal
5
JMKIA5210GB
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
4
D37
5
Existed
5
4
Power window main switch
Ground
Continuity
Connector
Terminal
D35
4
Not existed
5
Revision: November 2015
2016 JUKE
PWC-40
< DTC/CIRCUIT DIAGNOSIS >
ENCODER CIRCUIT
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCODER POWER SUPPLY
1. Connect power window main switch connector.
2. Turn ignition switch ON.
3. Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK ENCODER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4. Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK ENCODER GROUND CIRCUIT 1
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK ENCODER GROUND CIRCUIT 2
1. Connect power window main switch connector.
2. Check continuity between power window main switch connector and ground.
(+)
(-)
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D37
1
Ground
9 – 16
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
14
D37
1
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
14
Not existed
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
12
D37
6
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
12
Existed
Revision: November 2015
2016 JUKE
ENCODER CIRCUIT
PWC-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> Replace front power window motor (driver side). Refer to
GW-20, "Disassembly and Assembly"
.
NO
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
Revision: November 2015
2016 JUKE
PWC-42
< SYMPTOM DIAGNOSIS >
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure
INFOID:0000000012196934
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT
Check power window main switch power supply and ground circuit.
PWC-28, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст