Nissan Juke (2016 year). Service Repair Manual — part 533
POWER WINDOW SYSTEM
PWC-19
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
JRKWF4433GB
Revision: November 2015
2016 JUKE
PWC-20
< WIRING DIAGRAM >
POWER WINDOW SYSTEM
JRKWF4434GB
Revision: November 2015
2016 JUKE
POWER WINDOW SYSTEM
PWC-21
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
JRKWF4435GB
Revision: November 2015
2016 JUKE
PWC-22
< WIRING DIAGRAM >
POWER WINDOW SYSTEM
JRKWF4436GB
Revision: November 2015
2016 JUKE
DIAGNOSIS AND REPAIR WORK FLOW
PWC-23
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
WorkFlow
INFOID:0000000012196906
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 4.
4.
IDENTIFY THE MALFUNCTIONING PARTS WITH “DTC/CIRCUIT DIAGNOSIS”
Perform the diagnosis with “DTC/CIRCUIT DIAGNOSIS” of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES
>> INSPECTION END
NO
>> GO TO 3.
Revision: November 2015
2016 JUKE
PWC-24
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL
Description
INFOID:0000000012196907
When the battery negative terminal is disconnected, the initialization is necessary for normal operation of
power window system. Refer to
.
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000012196908
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
.
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
.
>> END
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
PWC-25
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description
INFOID:0000000012196909
When the control unit replaced, the initialization in necessary for normal operation of power window system.
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000012196910
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
.
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
.
>> END
Revision: November 2015
2016 JUKE
PWC-26
< BASIC INSPECTION >
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION
Description
INFOID:0000000012196911
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system. Refer to
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000012196912
1.
STEP 1
1. Close the door.
2. Turn ignition switch ON.
3. Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open)
4. Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 2 seconds or more.
5. Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
.
>> END
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст