Nissan Juke (2016 year). Service Repair Manual — part 534
CHECK ANTI-PINCH FUNCTION
PWC-27
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
CHECK ANTI-PINCH FUNCTION
Description
INFOID:0000000012196913
If any of the following operations are performed, the initialization is necessary for normal operation of anti-
.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure
INFOID:0000000012196914
1.
CHECK ANTI-PINCH FUNCTION
1. Close the door.
2. Fully open the door window.
3. Place a piece of wood near fully closed position.
4. Close door glass completely with AUTO-UP.
5. Check the following conditions.
-
Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
-
Check that glass does not rise not when operating the power window main switch while lowering.
CAUTION:
•
Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-
mally.
•
Check that AUTO-UP operates before inspection when system initialization is performed.
•
Do not check with hands and other body parts because they may be pinched. Do not get
pinched.
>> END
Revision: November 2015
2016 JUKE
PWC-28
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000012196915
1.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check voltage between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and power window main switch harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace harness.
3.
CHECK POWER WINDOW MAIN SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
(+)
(-)
Condition
Voltage (V)
Power window main switch
Connector
Terminal
D35
10
Ground
Ignition switch
ON
9 – 16
D36
18
OFF
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M69
68
D35
10
Existed
69
D36
18
BCM
Ground
Continuity
Connector
Terminal
M69
68
Not existed
69
Power window main switch
Ground
Continuity
Connector
Terminal
D35
1
Existed
Revision: November 2015
2016 JUKE
POWER SUPPLY AND GROUND CIRCUIT
PWC-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure
INFOID:0000000012196916
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect front power window switch (passenger side) connector.
3. Turn ignition switch ON.
4. Check voltage between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace harness.
REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH : Diagnosis Procedure
INFOID:0000000012196917
1.
CHECK REAR POWER WINDOW SWITCH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect rear power window switch connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window switch harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
(+)
(-)
Voltage (V)
Front power window switch (passenger side)
Connector
Terminal
D10
1
Ground
9 – 16
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69
68
D10
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
68
Not existed
(+)
(-)
Voltage (V)
Rear power window switch
Connector
Terminal
LH
D63
1
Ground
9 – 16
RH
D43
Revision: November 2015
2016 JUKE
PWC-30
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
2.
CHECK REAR POWER WINDOW SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear power window switch harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace harness.
BCM
Rear power window switch
Continuity
Connector
Terminal
Connector
Terminal
M69
68
LH
D63
1
Existed
RH
D43
BCM
Ground
Continuity
Connector
Terminal
M69
68
Not existed
Revision: November 2015
2016 JUKE
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
PWC-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Component Function Check
INFOID:0000000012196918
1.
CHECK FUNCTION
Check front power window motor (passenger side) operation with front power window switch (passenger side)
and power window main switch (passenger side switch).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196919
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window switch (passenger side) connector.
3. Turn ignition switch ON.
4. Check voltage between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between front power window switch (passenger side) harness connector and power win-
dow main switch harness connector.
4. Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
PWC-32, "Component Inspection"
(+)
(-)
Condition
Voltage (V)
Front power window switch (passenger side)
Connector
Terminal
D10
2
Ground
Power window main
switch
(passenger side
switch)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window switch (passenger side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D10
2
D35
16
Existed
3
2
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D10
2
Not existed
3
Revision: November 2015
2016 JUKE
PWC-32
< DTC/CIRCUIT DIAGNOSIS >
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace front power window switch (passenger side). Refer to
PWC-54, "Removal and Installa-
.
4.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000012196920
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
1. Turn ignition switch OFF.
2. Disconnect front power window switch (passenger side) connector.
3. Check front power window switch (passenger side) terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front power window switch (passenger side). Refer to
PWC-54, "Removal and Installa-
.
Front power window switch (passenger side)
Condition
Continuity
Terminal
1
5
UP
Existed
3
4
2
5
NEUTRAL
3
4
1
4
DOWN
2
5
Revision: November 2015
2016 JUKE
REAR POWER WINDOW SWITCH
PWC-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Component Function Check
INFOID:0000000012196921
1.
CHECK FUNCTION
Check rear power window motor (LH/RH) operation with rear power window switch (LH/RH) and pawer win-
dow main switch (rear LH/RH switch).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196922
1.
CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window switch connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between rear power window switch harness connector and power window main switch
harness connector.
4. Check continuity between rear power window switch harness connector and ground.
(+)
(-)
Condition
Voltage (V)
Rear power window switch
Connector
Terminal
LH
D63
2
Ground
Power window main
switch
(rear LH switch)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
RH
D43
2
Power window main
switch
(rear RH switch)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Rear power window switch
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
LH
D63
2
D35
9
Existed
3
8
RH
D43
2
7
3
6
Revision: November 2015
2016 JUKE
PWC-34
< DTC/CIRCUIT DIAGNOSIS >
REAR POWER WINDOW SWITCH
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-54, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK REAR POWER WINDOW SWITCH
Check rear power window switch.
PWC-34, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear power window switch. Refer to
PWC-54, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000012196923
1.
CHECK REAR POWER WINDOW SWITCH
1. Turn ignition switch OFF.
2. Disconnect rear power window switch connector.
3. Check rear power window switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace rear power window switch. Refer to
PWC-54, "Removal and Installation"
Rear power window switch
Ground
Continuity
Connector
Terminal
LH
D63
2
Not existed
3
RH
D43
2
3
Rear power window switch
Condition
Continuity
Terminal
1
5
UP
Existed
3
4
2
5
NEUTRAL
3
4
1
4
DOWN
2
5
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст