Nissan Juke (2016 year). Service Repair Manual — part 112
DLK-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
3. Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR LOCK ASSEMBLY CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR SWITCH
DLK-78, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning door switch.
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000012196643
1.
CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check continuity between door switch terminals.
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
B48
2
B10
47
Existed
Passenger side
B49
45
Rear LH
B71
48
Rear RH
B53
46
Back door
D106
3
43
Door switch
Ground
Continuity
Connector
Terminal
Driver side
B48
2
Not existed
Passenger side
B49
Rear LH
B71
Rear RH
B53
Back door
D106
3
Back door switch
Ground
Continuity
Connector
Terminal
D106
4
Existed
Revision: November 2015
2016 JUKE
DOOR SWITCH
DLK-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace malfunction door switch.
Door switch
Condition
Continuity
Terminal
Driver side
2
Ground part of door
switch
Door switch
Pressed
Existed
Released
Not existed
Passenger side
Pressed
Existed
Released
Not existed
Rear LH
Pressed
Existed
Released
Not existed
Rear RH
Pressed
Existed
Released
Not existed
Back door
3
4
Back door lock as-
sembly
Lock
Existed
Unlock
Not existed
Revision: November 2015
2016 JUKE
DLK-80
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Component Function Check
INFOID:0000000012196644
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “FLASHER” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196645
1.
CHECK HAZARD SWITCH CIRCUIT
EXL-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Monitor item
Status
FLASHER
LH
Front turn signal lamp LH
Turns ON
RH
Front turn signal lamp RH
Turns ON
OFF
Front turn signal lamp
Turns OFF
Revision: November 2015
2016 JUKE
INTELLIGENT KEY BATTERY
DLK-81
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Component Inspection
INFOID:0000000012196646
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key battery.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
Revision: November 2015
2016 JUKE
DLK-82
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Component Function Check
INFOID:0000000012196647
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196648
1.
CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10 A fuse, [No. 13, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.
CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Disconnect Intelligent Key warning buzzer connector.
2. Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
Monitor item
Status
OUTSIDE BUZZER
ON
Outside warning buzzer
Buzzer sounds
OFF
Buzzer does not sound
(+)
(–)
Voltage
(Approx.)
Intelligent Key warning buzzer
Connector
Terminal
E25
1
Ground
Battery voltage
BCM
Intelligent Key warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
M70
93
E25
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
93
Not existed
Revision: November 2015
2016 JUKE
INTELLIGENT KEY WARNING BUZZER
DLK-83
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
CHECK INTELLIGENT KEY WARNING BUZZER
DLK-83, "Component Inspection"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Replace Intelligent Key warning buzzer.
Component Inspection
INFOID:0000000012196649
1.
CHECK INTELLIGENT KEY WARNING BUZZER
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key warning buzzer connector.
3. Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera-
tion.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key warning buzzer.
Intelligent Key warning buzzer
Operation
Terminal
(+)
(
−
)
1
3
Buzzer sounds
Revision: November 2015
2016 JUKE
DLK-84
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEY WARNING LAMP
KEY WARNING LAMP
Component Function Check
INFOID:0000000012196650
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INDICATOR” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Key warning lamp is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196651
1.
CHECK KEY WARNING LAMP
MWI-21, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Monitor item
Status
INDICATOR
KEY ON
Key warning lamp
Turns ON
KEY IND
Blinks
OFF
Turns OFF
Revision: November 2015
2016 JUKE
REMOTE KEYLESS ENTRY RECEIVER
DLK-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000012196652
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196653
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect remote keyless entry receiver connector.
3. Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (No. 7)
• Harness for open or short between remote keyless entry receiver and battery
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
(+)
(–)
Voltage
Remote keyless entry receiver
Connector
Terminal
M75
1
Ground
Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
18
M75
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
18
Existed
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст