Nissan Juke (2016 year). Service Repair Manual — part 379
FRONT GRILLE
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Exploded View
INFOID:0000000012199314
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
1.
Bumper fascia
2.
Front side grille RH
3.
Front center grille
4.
Emblem
5.
Front side grille LH
: Pawl
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB4175ZZ
Revision: November 2015
2016 JUKE
EXT-26
< REMOVAL AND INSTALLATION >
FRONT GRILLE
Removal and Installation
INFOID:0000000012199315
REMOVAL
Except for NISMO and NISMO RS
1. Fully open hood assembly.
2. Remove front center grille upper fixing clips (A).
CAUTION:
Apply protective tape (B) around bumper fascia.
1.
Bumper fascia
2.
Front upper grille
3.
Front grille
4.
Front grille emblem
5.
Emblem
: Pawl
, , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB4689ZZ
JMKIA5623ZZ
Revision: November 2015
2016 JUKE
FRONT GRILLE
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3. Disengage fixing pawls from back side while pulling front center
grille toward vehicle front, and then remove front center grille.
4. Remove front side grille (LH and RH) upper fixing clips (A).
5. Disengage fixing pawls from back side of front side grille, and
then remove front side grille (LH and RH).
CAUTION:
Apply protective tape (B) around bumper fascia.
6. Remove the following parts after removing front grille.
• Emblem
• Front camera (if equipped). Refer to
AV-191, "Removal and Installation"
NISMO and NISMO RS
1. Fully open hood assembly.
2. Remove front upper grille fixing clips (A), and then remove front
upper grille.
3. Remove front grille fixing clips (A).
: Pawl
JMKIA5756ZZ
: Pawl
JMKIA5624ZZ
JMKIB4690ZZ
JMKIB4693ZZ
Revision: November 2015
2016 JUKE
EXT-28
< REMOVAL AND INSTALLATION >
FRONT GRILLE
4. Disengage fixing pawls from back side of front grille, and then
remove front grille.
CAUTION:
Apply protective tape (A) around bumper fascia.
5. Remove the following parts after removing front grille.
• Emblem
• Front grille emblem
• Front camera (if equipped). Refer to
AV-191, "Removal and Installation"
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to
AV-116, "CALIBRATING CAMERA IMAGE (AROUND VIEW
.
: Pawl
JMKIB4691ZZ
Revision: November 2015
2016 JUKE
COWL TOP
EXT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Exploded View
INFOID:0000000012199316
1.
Front fender cover RH
2.
Cowl top cover seal
3.
Cowl top insulator
4.
Blind plug RH
5.
Cowl top cover cap
6.
Cowl top extension
7.
EPT seal [t: 3.0 mm (0.118 in)]
8.
Air intake cover
9.
Cowl top cover
10. Front fender cover LH
11. Washer nozzle
: Clip
JMKIA5940ZZ
Revision: November 2015
2016 JUKE
EXT-30
< REMOVAL AND INSTALLATION >
COWL TOP
Removal and Installation
INFOID:0000000012199317
REMOVAL
1. Fully open hood assembly.
2. Remove front wiper arm (LH and RH). Refer to
WW-50, "Removal and Installation"
3. Disconnect washer tube joint on cowl top cover RH.
4. Remove cowl top seal fixing clips, and then remove cowl top seal.
5. Remove cowl top insulator fixing clips, and then remove cowl top insulator.
6. Remove front fender cover (LH and RH).
7. Remove cowl top cover fixing clips.
8. Pull forward to release cowl top cover from windshield glass.
CAUTION:
When performing the procedure after removing cowl top
cover, cover the lower end of windshield glass with ure-
thane etc.
9. Remove cowl top cover.
10. Remove the following parts after removing cowl top cover.
• EPT sealer
• Washer tube
• Washer nozzle (LH and RH). Refer to
WW-47, "Removal and Installation"
.
11. Remove front wiper drive assembly. Refer to
WW-55, "Removal and Installation"
12. Remove cowl top extension mounting bolts, and then remove cowl top extension.
INSTALLATION
Note the following items and then, install in the reverse order of removal.
CAUTION:
• Clean the joint between the cowl top cover and the windshield, and then install them.
• Replace the EPT sealer on the back surface with new EPT sealer when reusing the cowl top cover.
• Remove the EPT sealer remaining on the cowl top cover using a double-faced adhesive tape remove.
• To maintain adhesion, never wash the vehicle within 24 hours after installation.
• Perform the stop position adjustment at the installation of the front wiper arms. Refer to
.
: Pawl
: Always replace after every disassembly.
JMKIA5621ZZ
Revision: November 2015
2016 JUKE
FENDER PROTECTOR
EXT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
Exploded View
INFOID:0000000012199318
Removal and Installation
INFOID:0000000012199319
REMOVAL
1.
Fender protector
2.
U nut
3.
Air guide
4.
Screw grommet
: Vehicle front
JMKIB4235ZZ
Revision: November 2015
2016 JUKE
EXT-32
< REMOVAL AND INSTALLATION >
FENDER PROTECTOR
1. Remove front fillet molding. Refer to
EXT-36, "FRONT FILLET MOLDING : Removal and Installation"
.
2. Remove air guide mounting bolts, and then remove air guide.
3. Remove front fender protector fixing screws and clips.
4. Remove front fender protector from wheel house.
INSTALLATION
Install in the reverse order of removal.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст