Nissan Pathfinder (2006 year). Manual — part 40
ASSEMBLY
AT-311
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
40. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
41. Install rear carrier assembly in direct clutch drum.
42. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
43. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
44. Install mid carrier assembly in rear carrier assembly.
SCIA5175E
SCIA2462E
SCIA2804E
SCIA2805E
SCIA5017E
AT-312
ASSEMBLY
2006 Pathfinder
45. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
46. Install seal rings in input clutch assembly.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
47. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
48. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
49. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
SCIA5015E
SCIA2470E
SCIA6512E
SCIA5498E
SCIA5014E
ASSEMBLY
AT-313
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
50. Install needle bearing to front sun gear.
CAUTION:
Apply petroleum jelly to needle bearing.
51. Adjust brake band tilting using a clips so that brake band con-
tacts front sun gear drum evenly.
52. Adjust brake band.
a.
Loosen lock nut.
b.
Tighten band servo anchor end pin to specified torque.
c.
Back of band servo anchor end pin three turns.
d.
Holding band servo anchor end pin, tighten lock nut to specified
torque.
Adjustment
ECS00EMA
TOTAL END PLAY
●
Measure clearance between front sun gear and bearing race for
oil pump cover.
●
Select proper thickness of bearing race so that end play is within
specifications.
SCIA2808E
SCIA5033E
Anchor end pin
: 5.0 N·m (0.51 kg-m, 44 in-lb)
Lock nut
: 46 N·m (4.7 kg-m, 34 ft-lb)
SCIA5498E
SCIA2810E
AT-314
ASSEMBLY
2006 Pathfinder
1.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
a.
Measure dimension “K”.
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
2.
Measure dimensions “M
1
” and “M
2
” and then calculate dimen-
sion “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
SCIA5350E
SCIA5351E
“J”: Distance between oil pump fitting surface of
transmission case and needle bearing mating surface
of front sun gear.
J = K – L
SCIA5352E
SCIA3125E
SCIA3124E
ASSEMBLY
AT-315
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
b.
Measure dimension “M
1
”.
c.
Measure dimension “M
2
”.
d.
Calculate dimension “M”.
3.
Adjust total end play “T
1
”.
●
Select proper thickness of bearing race so that total end play
is within specifications.
SCIA3126E
SCIA3127E
“M”: Distance between transmission case fitting sur-
face of oil pump and needle bearing on oil pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
”:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
Bearing races:
Refer to
SCIA2810E
AT-316
ASSEMBLY
2006 Pathfinder
Assembly (2)
ECS00EMB
1.
Install O-ring to oil pump assembly.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
2.
Install bearing race to oil pump assembly.
CAUTION:
Apply petroleum jelly to bearing race.
3.
Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump baring.
4.
Apply recommended sealant (Genuine RTV Silicone Sealant or
equivalent. Refer to
GI-47, "Recommended Chemical Products
.) to oil pump assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the oil pump bolts and oil pump bolt
mating surfaces.
SCIA5172E
SCIA6529E
SCIA2811E
SCIA5321E
ASSEMBLY
AT-317
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
5.
Tighten oil pump bolts to specified torque.
CAUTION:
Apply ATF to oil pump bushing.
6.
Install O-ring to input clutch assembly.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
7.
Install converter housing to transmission case and tighten bolts
to specified torque.
CAUTION:
Do not reuse self-sealing bolt.
8.
Make sure that brake band does not close turbine revolution
sensor hole.
9.
Install control valve with TCM.
a.
Connect TCM connector and park/neutral position switch con-
nector.
Oil pump bolts
: 48 N·m (4.9 kg-m, 35 ft-lb)
SCIA2300E
SCIA5011E
Converter housing bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA4634E
SCIA5034E
SCIA5449E
AT-318
ASSEMBLY
2006 Pathfinder
b.
Install A/T assembly harness connector to control valve with
TCM.
c.
Connect TCM connectors.
d.
Install O-ring to A/T assembly harness connector.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
e.
Install A/T fluid temperature sensor 2 to bracket.
f.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM and tighten bolt to specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
SCIA5450E
SCIA5447E
SCIA5155E
SCIA5264E
Bracket bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5301E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст