Nissan Murano Z51 (2008 year). Manual — part 115
DLK-372
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Exploded View
INFOID:0000000003318264
DLK-331, "DOOR STRIKER : Exploded View"
.
DRIVER SIDE : Removal and Installation
INFOID:0000000003318265
REMOVAL
Remove the front outside handle LH. Refer to
DLK-354, "OUTSIDE HANDLE : Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Exploded View
INFOID:0000000003318266
DLK-331, "DOOR STRIKER : Exploded View"
.
PASSENGER SIDE : Removal and Installation
INFOID:0000000003318267
REMOVAL
Remove the front outside handle RH. Refer to
DLK-354, "OUTSIDE HANDLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Exploded View
INFOID:0000000003318268
REAR BUMPER : Removal and Installation
INFOID:0000000003318269
REMOVAL
1.
Remove the rear bumper. Refer to
EXT-15, "Removal and Installation"
1.
Outside key antenna (rear bumper)
JMKIA2179ZZ
Revision: 2008 October
2009 Murano
OUTSIDE KEY ANTENNA
DLK-373
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Remove the outside key antenna (rear bumper) mounting nuts
(A), and then remove outside key antenna (rear bumper) (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2172ZZ
Revision: 2008 October
2009 Murano
DLK-374
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Exploded View
INFOID:0000000003318270
Removal and Installation
INFOID:0000000003318271
REMOVAL
1.
Remove the Intelligent Key warning buzzer mounting bolt (A),
and then remove the Intelligent Key warning buzzer (1).
INSTALLATION
Install in the reverse order of removal.
1.
Intelligent Key warning buzzer
JMKIA1827ZZ
JMKIA1828ZZ
Revision: 2008 October
2009 Murano
KEY SLOT
DLK-375
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY SLOT
Exploded View
INFOID:0000000003625923
Removal and Installation
INFOID:0000000003625924
REMOVAL
1.
Remove the instrument lower panel LH (2). Refer to
IP-12, "Removal and Installation"
2.
Disconnect key slot connector.
3.
Remove the key slot mounting screw (A), and then remove key
slot (1) from instrument lower panel LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Key slot
JMKIA1820ZZ
JMKIA1821ZZ
Revision: 2008 October
2009 Murano
DLK-376
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SWITCH ASSEMBLY
BACK DOOR OPENER SWITCH ASSEMBLY
Exploded View
INFOID:0000000003318274
Removal and Installation
INFOID:0000000003318275
REMOVAL
1.
Remove the back door finisher inner. Refer to
INT-37, "Removal and Installation"
2.
Remove the back door opener switch assembly (1), and then
remove pawl.
INSTALLATION
Install in the reverse order of removal.
1.
Back door opener switch assembly
JMKIA2181ZZ
JMKIA2175ZZ
Revision: 2008 October
2009 Murano
REMOTE KEYLESS ENTRY RECEIVER
DLK-377
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Exploded View
INFOID:0000000003318280
Removal and Installation
INFOID:0000000003318281
REMOVAL
1.
Remove the instrument lower panel RH. Refer to
IP-12, "Removal and Installation"
2.
Remove the remote keyless entry receiver mounting bolt (A),
and then remove remote keyless entry receiver (1).
INSTALLATION
Install in the reverse order of removal.
1.
Remote keyless entry receiver
JMKIA2178ZZ
JMKIA2171ZZ
Revision: 2008 October
2009 Murano
DLK-378
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY BATTERY
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000003625914
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2025)
PIIB6222E
Revision: 2008 October
2009 Murano
AUTOMATIC BACK DOOR CONTROL UNIT
DLK-379
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR CONTROL UNIT
Exploded View
INFOID:0000000003416343
Removal and Installation
INFOID:0000000003416344
REMOVAL
1.
Remove the luggage side finisher lower (RH). Refer to
INT-34, "Removal and Installation"
2.
Remove the automatic back door control unit bracket mounting
bolt (A) and nats (B), and then remove the automatic back door
control unit bracket.
3.
Remove the automatic back door control unit mounting bolt, and then remove the automatic back door
control unit.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing back door control unit, perform additional service when replace control unit. Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
1.
Automatic back door control unit
2.
Automatic back door control unit bracket
JMKIA2125ZZ
JMKIA2124ZZ
Revision: 2008 October
2009 Murano
DLK-380
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC BACK DOOR WARNING BUZZER
AUTOMATIC BACK DOOR WARNING BUZZER
Exploded View
INFOID:0000000003465223
.
Removal and Installation
INFOID:0000000003465224
REMOVAL
1.
Remove the rear bumper. Refer to
EXT-15, "Removal and Installation"
2.
Remove the automatic back door warning buzzer mounting nut
(A), and then remove the automatic back door warning buzzer
(1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2123ZZ
Revision: 2008 October
2009 Murano
AUTOMATIC BACK DOOR MAIN SWITCH
DLK-381
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR MAIN SWITCH
Exploded View
INFOID:0000000003465247
.
Removal and Installation
INFOID:0000000003465248
REMOVAL
1.
Remove the instrument driver lower panel LH. Refer to
IP-12, "Removal and Installation"
2.
Widen the pawl, and remove the automatic back door main switch (1) from switch bracket (2).
INSTALLATION
Install in the reverse order of removal.
:
Pawl
JMKIA1849ZZ
Revision: 2008 October
2009 Murano
DLK-382
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC BACK DOOR CLOSE SWITCH
AUTOMATIC BACK DOOR CLOSE SWITCH
Exploded View
INFOID:0000000003465250
Removal and Installation
INFOID:0000000003465251
REMOVAL
1.
Remove the automatic back door close switch finisher. Refer to
INT-37, "Removal and Installation"
.
2.
Widen the pawl, and remove the automatic back door close switch (1) from automatic back door close
switch finisher (2).
INSTALLATION
Install in the reverse order of removal.
:
Pawl
JMKIA1847ZZ
Revision: 2008 October
2009 Murano
AUTOMATIC BACK DOOR SWITCH
DLK-383
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR SWITCH
Exploded View
INFOID:0000000003465254
.
Removal and Installation
INFOID:0000000003465255
REMOVAL
1.
Remove the instrument driver lower panel. Refer to
IP-12, "Removal and Installation"
.
2.
Widen the pawl, and remove the automatic back door switch (1) from automatic back door switch finisher
(2).
INSTALLATION
Install in the reverse order of removal.
:
Pawl
JMKIA1848ZZ
Revision: 2008 October
2009 Murano
DLK-384
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000003443441
OVERALL SEQUENCE
DETAILED FLOW
JMKIA3620GB
Revision: 2008 October
2009 Murano
DIAGNOSIS AND REPAIR WORKFLOW
DLK-385
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.
CHECK FOR DTC
1.
Check DTC for BCM.
2.
Perform the following procedure if DTC is displayed.
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
DLK-509, "DTC Inspection Priority Chart"
(BCM) and determine
trouble diagnosis order.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Refer to
GI-40, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to Symptom Diagnosis based on the confirmed symptom in step 4.
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 8.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it.
Revision: 2008 October
2009 Murano
DLK-386
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
>> GO TO 9.
9.
FINAL CHECK
When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired.
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Are all malfunctions corrected?
NO (DTC is detected)>>GO TO 7.
NO (Symptom remains)>>GO TO 6.
YES
>> INSPECTION END
Revision: 2008 October
2009 Murano
INSPECTION AND ADJUSTMENT
DLK-387
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003443442
Perform the system initialization when replacing or registering keyfob and ignition key.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003443443
Refer to the CONSULT-III Operation Manual-NATS.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст