Nissan Murano Z51 (2008 year). Manual — part 114
DLK-356
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000003470343
DOOR LOCK : Removal and Installation
INFOID:0000000003470344
REMOVAL
1.
Fully close rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen. Refer to
GW-23, "Removal and Installation"
.
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1803GB
JMKIA1467ZZ
Revision: 2008 October
2009 Murano
REAR DOOR LOCK
DLK-357
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
10. Disconnect harness connector from door lock actuator.
11. Remove door lock mounting bolts.
12. Remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
Revision: 2008 October
2009 Murano
DLK-358
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
INSIDE HANDLE : Exploded View
INFOID:0000000004749759
INSIDE HANDLE : Removal and Installation
INFOID:0000000003470346
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting screws.
3.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1803GB
Revision: 2008 October
2009 Murano
REAR DOOR LOCK
DLK-359
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded View
INFOID:0000000004749767
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000003470348
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
2.
Fully close rear door glass.
3.
Remove sealing screen. Refer to
GW-23, "Removal and Installation"
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
JMKIA1803GB
JMKIA1467ZZ
Revision: 2008 October
2009 Murano
DLK-360
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
Revision: 2008 October
2009 Murano
BACK DOOR LOCK
DLK-361
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000003470349
DOOR LOCK : Removal and Installation
INFOID:0000000003470350
REMOVAL
1.
Remove back door finisher inner. Refer to
INT-37, "Removal and Installation"
2.
Disconnect back door lock assembly and back door opener switch connectors.
3.
Remove back door lock mounting bolts, and then remove back door lock assembly.
JMKIA1804GB
1.
TORX bolt
2.
Back door assembly
3.
Power back door drive assembly
4.
Back door lock assembly (normal)
5.
Back door lock assembly (super lock)
6.
Touch sensor (RH/LH)
7.
Cover
8.
Patch
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
DLK-362
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check back door open/close, lock/unlock operation after installation.
POWER BACK DOOR DRIVE ASSEMBLY
POWER BACK DOOR DRIVE ASSEMBLY : Exploded View
INFOID:0000000004749769
POWER BACK DOOR DRIVE ASSEMBLY : Removal and Installation
INFOID:0000000003470369
REMOVAL
JMKIA1804GB
1.
TORX bolt
2.
Back door assembly
3.
Power back door drive assembly
4.
Back door lock assembly (normal)
5.
Back door lock assembly (super lock)
6.
Touch sensor (RH/LH)
7.
Cover
8.
Patch
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
BACK DOOR LOCK
DLK-363
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove headlining. Refer to
INT-26, "NORMAL ROOF : Removal and Installation"
(NORMAL ROOF),
INT-29, "SUNROOF : Removal and Installation"
(SUNROOF).
2.
Disconnect power back door drive assembly connector.
3.
Remove mounting bolts of power back door drive assembly (1)
(back door side).
4.
Remove mounting bolts of power back door drive assembly (1)
(body side), and then remove power back door drive assembly.
CAUTION:
Remove the bolts of power back door drive assembly refer-
ring to figure.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install the bolts of power back door drive assembly in the reverse order of removal.
• Check back door open/close operation after installation.
TOUCH SENSOR
JMKIA1918ZZ
JMKIA1919ZZ
Revision: 2008 October
2009 Murano
DLK-364
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
TOUCH SENSOR : Exploded View
INFOID:0000000004749770
TOUCH SENSOR : Removal and Installation
INFOID:0000000003470365
CAUTION:
Take care not to bend touch sensor.
REMOVAL
1.
Remove back door finisher inner. Refer to
INT-37, "Removal and Installation"
2.
Disconnect touch sensor connector.
JMKIA1804GB
1.
TORX bolt
2.
Back door assembly
3.
Power back door drive assembly
4.
Back door lock assembly (normal)
5.
Back door lock assembly (super lock)
6.
Touch sensor (RH/LH)
7.
Cover
8.
Patch
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
BACK DOOR LOCK
DLK-365
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove clips and TORX bolts touch sensor (1).
CAUTION:
Remove the TORX bolts (black arrow) and clips (white
arrow) of touch sensor referring to figure.
4.
Pull harness of touch sensor out of back door and remove touch sensor.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install the clips and TORX bolts of touch sensor in the reverse order of removal.
• Never place back door side seal between touch sensor.
• Check back door open/close operation after installation.
JMKIA1920ZZ
Revision: 2008 October
2009 Murano
DLK-366
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000003515976
Removal and Installation
INFOID:0000000003515977
NOTE:
When fuel filler lid opener actuator is a defective operation, pull the
rod to open fuel filler lid.
REMOVAL
1.
Remove filler cap.
2.
Remove mounting screws (A), and then remove fuel filler lid (1).
3.
Remove luggage side finisher lower (LH). Refer to
INT-34, "Removal and Installation"
.
4.
Locate fuel filler lid opener actuator, and then remove the fuel
filler lid opener actuator.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
1.
Fuel filler lid assembly
2.
Bumper rubber
3.
Fuel filler lid opener actuator
JMKIA1957ZZ
JMKIA1960ZZ
JMKIA1959ZZ
Revision: 2008 October
2009 Murano
FUEL FILLER LID OPENER
DLK-367
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
Revision: 2008 October
2009 Murano
DLK-368
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Exploded View
INFOID:0000000003674417
Removal and Installation
INFOID:0000000003318257
REMOVAL
1.
Remove the door switch mounting bolt (A), and then remove
door switch (1).
INSTALLATION
Install in the reverse order of removal.
1.
Door switch
JMKIA2180ZZ
JMKIA2173ZZ
Revision: 2008 October
2009 Murano
INSIDE KEY ANTENNA
DLK-369
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE KEY ANTENNA
INSTRUMENT CENTER
INSTRUMENT CENTER : Exploded View
INFOID:0000000003318258
INSTRUMENT CENTER : Removal and Installation
INFOID:0000000003318259
REMOVAL
1.
Remove the AV C/U (audio unit). Refer to
IP-12, "Removal and Installation"
.
2.
Remove the key antenna mounting screw (A), and then remove
inside key antenna (instrument center) (1).
INSTALLATION
Install in the reverse order of removal.
CONSOLE
1.
Inside key antenna (instrument center)
JMKIA1814ZZ
JMKIA1815ZZ
Revision: 2008 October
2009 Murano
DLK-370
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
INSIDE KEY ANTENNA
CONSOLE : Exploded View
INFOID:0000000003318260
CONSOLE : Removal and Installation
INFOID:0000000003318261
REMOVAL
1.
Remove the console pocket and rear finisher. Refer to
IP-20, "Removal and Installation"
2.
Remove the inside key antenna mounting screw (A), and then
remove inside key antenna (console) (1) from console rear fin-
isher (2).
INSTALLATION
Install in the reverse order of removal.
LUGGAGE ROOM
1.
Inside key antenna (console)
JMKIA1818ZZ
JMKIA1819ZZ
Revision: 2008 October
2009 Murano
INSIDE KEY ANTENNA
DLK-371
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LUGGAGE ROOM : Exploded View
INFOID:0000000003318262
LUGGAGE ROOM : Removal and Installation
INFOID:0000000003318263
REMOVAL
1.
Remove the luggage floor finisher front. Refer to
INT-34, "Removal and Installation"
.
2.
Remove the inside key antenna (luggage room) mounting clip
(A), and then remove inside key antenna (luggage room) (1).
INSTALLATION
Install in the reverse order of removal.
1.
Inside key antenna (luggage room)
JMKIA1816ZZ
JMKIA1817ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст