Nissan Murano Z51 (2008 year). Manual — part 127
DLK-564
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR WEATHER-STRIP : Exploded View
INFOID:0000000004749841
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000004749844
REMOVAL
1.
Remove mounting bolts of power back door drive assembly (1)
(back door side).
2.
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark (A) with vehicle center mark (cutting posi-
tion) and install weather-strip onto the vehicle.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
JMKIA1918ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-565
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
For the lower section, align weather-strip seam with center of back door striker.
3.
Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Make sure that weather-strip is fit tightly at each corner and luggage rear plate.
4.
Install mounting bolts of power back door drive assembly (back door side).
Revision: 2008 October
2009 Murano
DLK-566
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000004749845
Removal and Installation
INFOID:0000000004749846
REMOVAL
CAUTION:
Check wiring of hood lock control before removal.
1.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
2.
Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
3.
Disconnect hood lock cable (2) from hood lock assembly.
4.
Remove instrument lower panel (LH). Refer to
IP-12, "Removal and Installation"
5.
Disconnect hood lock cable from instrument lower panel (LH).
6.
Remove fender protector (LH). Refer to
EXT-23, "FENDER PROTECTOR : Removal and Installation"
7.
Remove hood lock cable clamp.
1.
Hood lock assembly
2.
Hood lock control cable
3.
Hood lock opener
: Clip
Refer to
for symbols in the figure.
JMKIA1798ZZ
JMKIA1914ZZ
Revision: 2008 October
2009 Murano
HOOD LOCK
DLK-567
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never to damage (peeling) the outside of hood lock control cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-538, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000004749847
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4.
Install so that static closing face of hood is 94 – 490 N·m (9.6 – 50.0 kg-m, 69 – 361 ft – lb).
NOTE:
• Exert vertical force on right side and left side of hood lock.
• Never press simultaneously both sides.
5.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
PIIB5801E
Revision: 2008 October
2009 Murano
DLK-568
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000004749848
DOOR LOCK : Removal and Installation
INFOID:0000000004749849
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
2.
Remove front door glass. Refer to
GW-17, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-20, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1802GB
Revision: 2008 October
2009 Murano
FRONT DOOR LOCK
DLK-569
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never forcibly remove TORX bolt.
6.
Reach in to separate door key rod connection (on the handle)
(driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
JMKIA0020ZZ
1.
Door key cylinder assembly
2.
Key rod
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
Revision: 2008 October
2009 Murano
DLK-570
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
12. Remove door lock assembly TORX bolts.
13. Disconnect door lock actuator connector, and then remove door lock assembly.
14. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000004749852
PIIB5814E
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
JMKIA1802GB
Revision: 2008 October
2009 Murano
FRONT DOOR LOCK
DLK-571
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE HANDLE : Removal and Installation
INFOID:0000000004749854
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
2.
Remove inside handle mounting screws.
3.
Disconnect inside handle cable, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Exploded View
INFOID:0000000004749857
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
JMKIA1802GB
Revision: 2008 October
2009 Murano
DLK-572
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000004749859
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
2.
Remove front door glass. Refer to
GW-17, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-17, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never forcibly remove TORX bolt.
6.
Reach in to separate door key rod connection (on the handle)
(driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
JMKIA0020ZZ
1.
Door key cylinder assembly
2.
Key rod
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR LOCK
DLK-573
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
PIIB5814E
Revision: 2008 October
2009 Murano
DLK-574
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000004749860
DOOR LOCK : Removal and Installation
INFOID:0000000004749861
REMOVAL
1.
Fully close rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen. Refer to
GW-23, "Removal and Installation"
.
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1803GB
JMKIA1467ZZ
Revision: 2008 October
2009 Murano
REAR DOOR LOCK
DLK-575
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
10. Disconnect harness connector from door lock actuator.
11. Remove door lock mounting bolts.
12. Remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
Revision: 2008 October
2009 Murano
DLK-576
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
INSIDE HANDLE : Exploded View
INFOID:0000000004749864
INSIDE HANDLE : Removal and Installation
INFOID:0000000004749866
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting screws.
3.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1803GB
Revision: 2008 October
2009 Murano
REAR DOOR LOCK
DLK-577
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded View
INFOID:0000000004749869
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000004749871
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
2.
Fully close rear door glass.
3.
Remove sealing screen. Refer to
GW-23, "Removal and Installation"
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
JMKIA1803GB
JMKIA1467ZZ
Revision: 2008 October
2009 Murano
DLK-578
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
Revision: 2008 October
2009 Murano
BACK DOOR LOCK
DLK-579
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000004749872
DOOR LOCK : Removal and Installation
INFOID:0000000004749873
REMOVAL
1.
Remove back door finisher inner. Refer to
INT-37, "Removal and Installation"
2.
Disconnect back door lock assembly and back door opener switch connectors.
3.
Remove back door lock mounting bolts, and then remove back door lock assembly.
JMKIA1804GB
1.
TORX bolt
2.
Back door assembly
3.
Power back door drive assembly
4.
Back door lock assembly (normal)
5.
Back door lock assembly (super lock)
6.
Touch sensor (RH/LH)
7.
Cover
8.
Patch
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст