Murano Cross Cabriolet Z51 (2012 year). Manual — part 60
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-17
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PIIB8742E
Revision: 2013 February
2012 Murano CrossCabriolet
MIR-18
< REMOVAL AND INSTALLATION >
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View
INFOID:0000000007564810
Removal and Installation
INFOID:0000000007564811
REMOVAL
1.
Remove inside mirror cover.
2.
Disconnect harness connector from inside mirror.
3.
Loosen TORX bolt and slide inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
1.
Windshield glass
2.
Inside mirror base
3.
Harness connector
4.
TORX bolt
5.
Inside mirror assembly
6.
Inside mirror cover
N·m (kg·m, in-lb)
JMLIA0177GB
Revision: 2013 February
2012 Murano CrossCabriolet
DOOR MIRROR
MIR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR
Exploded View
INFOID:0000000007564812
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000007564813
CAUTION:
Never damage the mirror bodie.
REMOVAL
1.
Remove door finisher assembly. Refer to
INT-13, "Removal and Installation"
.
2.
Remove door mirror corner cover (1).
a.
Disengage the fixing clips with a remover tool (A).
b.
Slide lightly door mirror corner cover toward the direction of the
arrow 1 to remove it from weather-strip (2).
c.
Slide door mirror corner cover toward the direction of the arrow
2 to disengage the fixing pawls and remove.
1.
Door mirror cover
2.
Door mirror
3.
Glass mirror
4.
Door mirror corner cover
5.
Clip
6.
Front door corner finisher
: Clip
: Pawl
: N·m (kg·m, in-lb)
JMLIA2270GB
: Clip
: Pawl
JMLIA2271ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MIR-20
< REMOVAL AND INSTALLATION >
DOOR MIRROR
3.
Remove door mirror assembly (2).
a.
Disconnect harness connector (A) and remove the mounting nuts (B).
b.
Remove weather-strip (1) from door mirror assembly and pull out toward the direction of the arrow to
remove.
INSTALLATION
Install in the reverse order of removal.
GLASS MIRROR
GLASS MIRROR : Removal and Installation
INFOID:0000000007564814
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Place the glass mirror (1) upward.
2.
Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror and actuator and push up pawls to remove
glass.
CAUTION:
Put a strip of protective tape (A) on the housing.
NOTE:
Insert a flat-bladed screwdriver into recess, and push up while
rotating (twist) to make work easier.
3.
Insert flat-bladed screwdriver at left and right side between glass mirror and actuator, and push up pawls
to remove glass mirror.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.
4.
Disconnect both terminals (A) of mirror heater attachment. (With
heater mirror model)
5.
Remove glass mirror from actuator.
ASSEMBLY
Install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
JMLIA2272ZZ
JMLIA2273ZZ
JMLIA2274ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
DOOR MIRROR
MIR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR COVER
DOOR MIRROR COVER : Removal and Installation
INFOID:0000000007564815
CAUTION:
Never damage the mirror bodie.
DISASSEMBLY
1.
Remove glass mirror. Refer to
MIR-20, "GLASS MIRROR : Removal and Installation"
.
2.
Remove the actuator fixing screws (A) and then remove the
actuator.
3.
Disengage the door mirror cover fixing pawls (A) and remove the door mirror cover from housing.
ASSEMBLY
Install in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
FRONT DOOR CORNER FINISHER
FRONT DOOR CORNER FINISHER : Removal and Installation
INFOID:0000000007564816
REMOVAL
Remove front door corner finisher (1).
Insert a remover tool (A) between body panel and front door corner
finisher to disengage the fixing clips and pawl.
CAUTION:
Put a strip of protective tape on body panel to protect it from
damage.
INSTALLATION
CAUTION:
JMLIA2276ZZ
: Pawl
JMLIA2277ZZ
: Clip
: Pawl
JMKIA2261ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MIR-22
< REMOVAL AND INSTALLATION >
DOOR MIRROR
• When installing, check visually front door corner finisher fixing pawl and clips then replace them
with new parts if they have been damaged.
• When installing front door corner finisher, check that pawl and clips are securely fitted in door panel,
and then press pawls in.
Revision: 2013 February
2012 Murano CrossCabriolet
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and Installation
INFOID:0000000007564817
REMOVAL
1.
Remove the power window main switch finisher (2). Refer to
INT-13, "Removal and Installation"
2.
Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using remover tool (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0118ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
MWI-1
DRIVER INFORMATION & MULTIMEDIA
C
D
E
F
G
H
I
J
K
L
M
B
SECTION
MWI
A
O
P
CONTENTS
METER, WARNING LAMP & INDICATOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
METER SYSTEM . . . . . . . . . . . . . .....
METER SYSTEM : Component Parts Location . ....
METER SYSTEM : Component Description . . .....
METER SYSTEM . . . . . . . . . . . . .
METER SYSTEM . . . . . . . . . . . . . .....
METER SYSTEM : System Diagram . . . . . ....
METER SYSTEM : System Description . . . . ....
METER SYSTEM : Fail-Safe . . . . . . . . ..
SPEEDOMETER . . . . . . . . . . . . . .
SPEEDOMETER : System Diagram . . . . . ...
SPEEDOMETER : System Description . . . . ...
TACHOMETER . . . . . . . . . . . . . . ..
TACHOMETER : System Diagram . . . . . . .
TACHOMETER : System Description . . . . . .
ENGINE COOLANT TEMPERATURE GAUGE . .
ENGINE COOLANT TEMPERATURE GAUGE :
System Diagram . . . . . . . . . . . . . ..
ENGINE COOLANT TEMPERATURE GAUGE :
System Description . . . . . . . . . . . . .
FUEL GAUGE . . . . . . . . . . . . . . .
FUEL GAUGE : System Diagram . . . . . . .
FUEL GAUGE : System Description . . . . . ...
ODO/TRIP METER . . . . . . . . . . . . . .
ODO/TRIP METER : System Diagram . . . . .
ODO/TRIP METER : System Description . . . .
SHIFT POSITION INDICATOR . . . . . . . . ..
SHIFT POSITION INDICATOR : System Diagram .
SHIFT POSITION INDICATOR : System Descrip-
tion . . . . . . . . . . . . . . . . . . ...
WARNING LAMPS/INDICATOR LAMPS . . . . ..
WARNING LAMPS/INDICATOR LAMPS : System
Diagram . . . . . . . . . . . . . . . . ...
WARNING LAMPS/INDICATOR LAMPS : System
Description . . . . . . . . . . . . . . . ...
METER ILLUMINATION CONTROL . . . . . . .
METER ILLUMINATION CONTROL : System Di-
agram . . . . . . . . . . . . . . . . . ..
METER ILLUMINATION CONTROL : System De-
scription . . . . . . . . . . . . . . . . ...
INFORMATION DISPLAY . . . . . . . . . . ..
INFORMATION DISPLAY : System Diagram . . ..
INFORMATION DISPLAY : System Description . .
COMPASS . . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . ..
OPERATION . . . . . . . . . . . . . .
Switch Name and Function . . . . . . . . . ..
DIAGNOSIS SYSTEM (COMBINATION
METER) . . . . . . . . . . . . . . . .
On Board Diagnosis Function . . . . . . . . ..
CONSULT Function . . . . . . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
COMBINATION METER . . . . . . . . ...
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-2
Reference Value . . . . . . . . . . . . . .
Fail-Safe . . . . . . . . . . . . . . . . .
DTC Index . . . . . . . . . . . . . . . ..
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) . . . . .
List of ECU Reference . . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . .
METER SYSTEM . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . ...
COMPASS . . . . . . . . . . . . . . .
Wiring Diagram - COMPASS - . . . . . . . ....
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . . .
Work flow . . . . . . . . . . . . . . . ....
ZONE VARIATION SETTING (COMPASS) . ..
Work Procedure . . . . . . . . . . . . . ..
CALIBRATION (COMPASS) . . . . . . . .
Work Procedure . . . . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
U1000 CAN COMM CIRCUIT . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . .
U1010 CONTROL UNIT (CAN) . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2205 VEHICLE SPEED . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . .
B2267 ENGINE SPEED . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2268 WATER TEMP . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
COMBINATION METER . . . . . . . . . . ...
COMBINATION METER : Diagnosis Procedure ....
FUEL LEVEL SENSOR SIGNAL CIRCUIT . ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . .
METER CONTROL SWITCH SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
OIL PRESSURE SWITCH SIGNAL CIRCUIT ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
PARKING BRAKE SWITCH SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
WASHER LEVEL SWITCH SIGNAL CIRCUIT ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
A/C AUTO AMP. CONNECTION RECOGNI-
TION SIGNAL CIRCUIT . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . .
THE FUEL GAUGE POINTER DOES NOT
MOVE . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE METER CONTROL SWITCH IS INOPER-
ATIVE . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
MWI-3
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE DOOR OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE TRUNK OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE AMBIENT TEMPERATURE DISPLAY IS
INCORRECT . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
NORMAL OPERATING CONDITION . . . . .
COMPASS . . . . . . . . . . . . . . . . .
COMPASS : Description . . . . . . . . . . ..
INFORMATION DISPLAY . . . . . . . . . . ..
INFORMATION DISPLAY : Description . . . . ..
REMOVAL AND INSTALLATION . . . ...
COMBINATION METER . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
METER CONTROL SWITCH . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COMPASS . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007565057
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000007565058
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007565059
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
PREPARATION
MWI-5
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000007565060
Tool name
Description
Power tool
Loosening screws
PBIC0191E
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
METER SYSTEM
METER SYSTEM : Component Parts Location
INFOID:0000000007565061
METER SYSTEM : Component Description
INFOID:0000000007565062
JSNIA4274ZZ
1.
Fuel level sensor unit (sub)
2.
Fuel level sensor unit and fuel pump
(main)
3.
ABS actuator and electric unit (con-
trol unit)
Refer to
4.
Oil pressure switch
5.
Washer level switch
6.
TCM
Refer to
SYSTEM : Component Parts Loca-
tion"
7.
8.
ECM
Refer to
SYSTEM : Component Parts Loca-
tion"
9.
IPDM E/R
Refer to
10.
SYSTEM : Component Parts Loca-
tion"
11. Parking brake switch
12. Combination meter
13. CVT shift selector
14. Meter control switch
A.
Lower side of rear seat
B.
Engine front side
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
COMPONENT PARTS
MWI-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Unit
Description
Combination meter
Controls the following with the signals received from each unit via CAN communication and the sig-
nals from switches and sensors.
• Speedometer
• Tachometer
• Engine coolant temperature gauge
• Fuel gauge
• Warning lamps
• Indicator lamps
• Meter illumination control
• Information display
IPDM E/R
IPDM E/R reads the ON/OFF signals of the oil pressure switch and transmits the oil pressure switch
signal to the combination meter via BCM with CAN communication line.
Fuel level sensor unit
Transmits the fuel level sensor signal to the combination meter.
Oil pressure switch
Transmits the oil pressure switch signal to the IPDM E/R.
ECM
Transmits the following signals to the combination meter with CAN communication line.
• Engine speed signal
• Engine coolant temperature signal
• Fuel consumption monitor signal
• Fuel filler cap warning display signal
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter with CAN communication line.
BCM
Transmits signals provided by various units to the combination meter with CAN communication line.
CVT shift selector
Transmits the O/D OFF switch signal to the combination meter.
TCM
Transmits the shift position signal to the combination meter with CAN communication line.
Meter control switch
Transmits the following signals to the combination meter.
• Enter switch signal
• Select switch signal
• Trip reset switch signal
• Illumination control switch signal (+)
• Illumination control switch signal (
−
)
Washer level switch
Transmits the washer level signal to the combination meter.
Parking brake switch
Transmits the parking brake switch signal to the combination meter.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-8
< SYSTEM DESCRIPTION >
METER SYSTEM
METER SYSTEM
METER SYSTEM
METER SYSTEM : System Diagram
INFOID:0000000007565063
METER SYSTEM : System Description
INFOID:0000000007565064
COMBINATION METER
• The combination meter receives the information required to control the operation of each gauge, indicator/
warning lamp, and information display via CAN communication from each unit, each switch, and sensor.
• The combination meter incorporates a trip computer that displays warnings and messages on the informa-
tion display according to the information received from various units.
• The combination meter incorporates a buzzer function that sounds an audible alarm with the integrated
buzzer device. Refer to
WCS-6, "WARNING CHIME SYSTEM : System Description"
for further details.
• The combination meter integrates the meter circuit check function and the segment check function that
checks the information display operation.
IPDM E/R
• IPDM E/R reads the ON/OFF signals of the oil pressure switch and transmits the oil pressure switch signal to
the combination meter via BCM with the CAN communication line.
• IPDM E/R is equipped with the diagnosis function. It can perform the operation check of oil pressure warning
lamp with the auto active test and the diagnosis with CONSULT.
METER CONTROL FUNCTION LIST
JSNIA4366GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
METER SYSTEM
MWI-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
System
Description
Signal source
Meter/gauge
Speedometer
Receives vehicle speed signal and indicates vehicle speed.
ABS actuator and elec-
tric unit (control unit)
Tachometer
Receives engine speed signal and indicates engine speed.
ECM
Fuel gauge
Receives fuel level sensor signal and indicates fuel level.
Fuel level sensor unit
Engine coolant tem-
perature gauge
Receives engine coolant temperature signal and indicates coolant
temperature.
ECM
Warning lamp/
indicator lamp
Oil pressure warning
lamp
Receives oil pressure warning lamp signal and illuminates warning
lamp.
IPDM E/R
Master warning
Illuminates according to warning output on information display.
—
Information
display
Door open warning
Receives door switch signals and displays warning.
BCM
Trunk open warning
Receives trunk switch signal and displays warning.
BCM
Parking brake re-
lease warning
Receives parking brake switch signal and vehicle speed signal and
displays warnings.
Parking brake switch
ABS actuator and elec-
tric unit (control unit)
Low fuel warning
Receives fuel gauge signal and displays warning if fuel level de-
creases to 9.8
(2-5/8 US gal, 2-1/8 Imp gal) or less.
Fuel level sensor unit
Low washer fluid
warning
Receives washer level switch signal and displays warning.
Washer level switch
Low outside tempera-
ture warning
Monitors ambient sensor signal and displays warning if ambient
temperature decreases to 3
°
C (37
°
F) or less. (If enabled)
Ambient sensor
Low tire pressure
warning
Receives low tire pressure warning lamp signal and displays warn-
ing.
BCM
Fuel filler cap warning
Receives fuel filler cap warning display signals and displays warn-
ing.
ECM
Instantaneous fuel
consumption
Calculates instantaneous fuel consumption based on received ve-
hicle speed signals and fuel consumption monitor signal and dis-
plays it.
ECM
ABS actuator and elec-
tric unit (control unit)
Average fuel con-
sumption
Calculates average fuel consumption in a reset-to-reset interval
based on received vehicle speed signals and fuel consumption
monitor signal and displays it.
ECM
ABS actuator and elec-
tric unit (control unit)
Average vehicle
speed
Calculates average vehicle speed in a reset-to-reset interval based
on received vehicle speed signals and displays it.
ABS actuator and elec-
tric unit (control unit)
Travel time
Displays accumulated key switch ON time from reset to reset.
—
Travel distance
Calculates accumulated travel distance in a reset-to-reset interval
based on received vehicle speed signals and displays it.
ABS actuator and elec-
tric unit (control unit)
Possible driving dis-
tance
Calculates possible driving distance based on received fuel con-
sumption monitor signal, vehicle speed signals and fuel level sen-
sor signal and displays it.
ABS actuator and elec-
tric unit (control unit)
ECM
Fuel level sensor unit
Ambient air tempera-
ture
Corrects ambient air temperature value based on received ambient
sensor signals and displays it.
Ambient sensor
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст