Murano Cross Cabriolet Z51 (2012 year). Manual — part 61
MWI-10
< SYSTEM DESCRIPTION >
METER SYSTEM
ARRANGEMENT OF COMBINATION METER
METER SYSTEM : Fail-Safe
INFOID:0000000007710088
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
JSNIA4262ZZ
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control
When suspending communication, changes to nighttime
mode.
Information display
Door open warning
The display turns off by suspending communication.
Trunk open warning
Parking brake release warning
Low tire pressure warning
Fuel filler cap warning
Instantaneous fuel warning
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition
is indicated.
Average fuel consumption
Average vehicle speed
Travel distance
Buzzer
The buzzer turns off by suspending communication.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
METER SYSTEM
MWI-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SPEEDOMETER
SPEEDOMETER : System Diagram
INFOID:0000000007565066
SPEEDOMETER : System Description
INFOID:0000000007565067
• The ABS actuator and electric unit (control unit) converts the rectangular wave signal provided by the wheel
sensor to a vehicle speed signal and transmits it to the combination meter via CAN communication.
• The combination meter indicates the vehicle speed to the speedometer according to the vehicle speed sig-
nal received via CAN communication.
TACHOMETER
TACHOMETER : System Diagram
INFOID:0000000007565068
Warning lamp/indicator
lamp
ABS warning lamp
The lamp turns on by suspending communication.
VDC warning lamp
Brake warning lamp
AWD warning lamp
Malfunction indicator lamp
Low tire pressure warning lamp
The lamp turns ON after flashing for 1 minute.
High beam indicator lamp
The lamp turns off by suspending communication.
Turn signal indicator lamp
Light indicator lamp
Oil pressure warning lamp
CRUISE indicator lamp
O/D OFF indicator lamp
VDC OFF indicator lamp
AWD LOCK indicator lamp
Key warning lamp
Function
Specifications
JSNIA0289GB
JSNIA0290GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-12
< SYSTEM DESCRIPTION >
METER SYSTEM
TACHOMETER : System Description
INFOID:0000000007565069
• ECM converts the pulse signal provided by the crankshaft position sensor to an engine speed signal and
transmits it to the combination meter via CAN communication.
• The combination meter indicates the engine speed to the tachometer according to the engine speed signal
received via CAN communication.
ENGINE COOLANT TEMPERATURE GAUGE
ENGINE COOLANT TEMPERATURE GAUGE : System Diagram
INFOID:0000000007565070
ENGINE COOLANT TEMPERATURE GAUGE : System Description
INFOID:0000000007565071
• ECM reads the engine coolant temperature signal from the engine coolant temperature sensor and transmits
the signal to the combination meter via CAN communication.
• The combination meter indicates the engine coolant temperature to the engine coolant temperature gauge
according to the engine coolant temperature signal received via CAN communication.
FUEL GAUGE
FUEL GAUGE : System Diagram
INFOID:0000000007565072
FUEL GAUGE : System Description
INFOID:0000000007565073
CONTROL OUTLINE
The combination meter reads the fuel level sensor signal from the fuel level sensor unit and indicates the fuel
level to the fuel gauge.
REFUEL CONTROL
The combination meter accelerates the fuel gauge segment if the all conditions listed below are met, or the
ignition switch is ON from OFF.
• Ignition switch is ON position.
• The vehicle is not moving.
• The fuel level change by 15 (4 US gal, 3-1/4 lmp gal) or more.
ODO/TRIP METER
JSNIA0291GB
JSNIA0511GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
METER SYSTEM
MWI-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ODO/TRIP METER : System Diagram
INFOID:0000000007565074
ODO/TRIP METER : System Description
INFOID:0000000007565075
• The ABS actuator and electric unit (control unit) reads the rectangular wave signal provided by the wheel
sensor and transmits the vehicle speed signal to the combination meter via CAN communication.
• The combination meter converts the vehicle speed signal received via CAN communication to mileage, and
it displays the accumulated mileage to the odo/trip meter.
SHIFT POSITION INDICATOR
SHIFT POSITION INDICATOR : System Diagram
INFOID:0000000007565076
SHIFT POSITION INDICATOR : System Description
INFOID:0000000007565077
• Shift position is displayed in the shift position indicator in the combination meter.
• TCM transmits the shift position signal to the combination meter via CAN communication.
• The combination meter indicates shift position according to the shift position signal received via CAN com-
munication.
WARNING LAMPS/INDICATOR LAMPS
WARNING LAMPS/INDICATOR LAMPS : System Diagram
INFOID:0000000007565078
WARNING LAMPS/INDICATOR LAMPS : System Description
INFOID:0000000007565079
OIL PRESSURE WARNING LAMP
• IPDM E/R reads the ON/OFF signals from the oil pressure switch and transmits the oil pressure switch sig-
nal to the combination meter via BCM with the CAN communication line.
JSNIA0293GB
JPNIA0745GB
JSNIA0449GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-14
< SYSTEM DESCRIPTION >
METER SYSTEM
• The combination meter turns the oil pressure warning lamp ON/OFF according to the oil pressure switch sig-
nal received via CAN communication.
METER ILLUMINATION CONTROL
METER ILLUMINATION CONTROL : System Diagram
INFOID:0000000007565080
METER ILLUMINATION CONTROL : System Description
INFOID:0000000007565081
SYSTEM DESCRIPTION
The combination meter controls the meter illumination by the illumination control switch signal from the meter
control switch and the position light request signal transmitted by the BCM via CAN communication.
Daytime Mode
Meter illumination level can be adjusted in 22 steps using the illumi-
nation control switch (1) in daytime mode.
Nighttime Mode
• Combination meter changes the meter illumination to the nighttime mode by the position light request signal
from BCM via CAN communication.
• Meter illumination can be adjusted in 22 steps using the illumination control switch in nighttime mode.
Driver Welcome Function
Ring illumination gradually turns ON when a driver gets in the vehicle with intelligent key and closes the driver
side door.
NOTE:
Ring illumination gradually turns OFF when not turning the ignition switch ON at a certain period of time.
Dial Effects Function
Combination meter detects the engine start when input engine speed signal at first. Pointers of speed meter
and tachometer sweep and ring illumination gradually turns ON when combination meter detects the engine
start. Then, combination meter starts the normal control.
NOTE:
• Engine coolant temperature gauge and fuel gauge do not function.
• Dial Effects Function can be turned ON/OFF from “SETTING” on the information display.
INFORMATION DISPLAY
JPNIA0746GB
JPNIA0742ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
METER SYSTEM
MWI-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INFORMATION DISPLAY : System Diagram
INFOID:0000000007565082
INFORMATION DISPLAY : System Description
INFOID:0000000007565083
DESCRIPTION
• The combination meter receives the information required for controlling the operations of the information dis-
play from the BCM via CAN communication.
• The combination meter incorporates a trip computer that displays the warning / information according to the
information received from various units.
PARKING BRAKE RELEASE WARNING
The combination meter indicates the parking brake release warning judged by the vehicle speed signal
received from the ABS actuator and electric unit (control unit) via CAN communication and the parking brake
switch signal from the parking brake switch.
Warning Operation Condition
Parking brake release warning is judged if all of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
LOW FUEL WARNING
The combination meter indicates the low fuel warning judged by the fuel level sensor signal received from the
fuel level sensor unit.
Warning Operation Condition
• Fuel level: Approx. 9.8 (2-5/8 US gal, 2-1/8 Imp gal) or less
LOW WASHER FLUID WARNING
The combination meter indicates the low washer fluid warning judged by the signal from the washer level
switch.
Warning Operation Condition
JPNIA0747GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-16
< SYSTEM DESCRIPTION >
METER SYSTEM
• Indicates the warning when the washer level switch is ON for 180 seconds or more. Stops indicating the
warning when the washer level switch is OFF for 30 seconds or more.
LOW TIRE PRESSURE WARNING
• The combination meter receives remaining low tire pressure warning lamp signal from the BCM with CAN
communication line.
• The combination meter indicates low tire pressure warning when receiving remaining low tire pressure warn-
ing lamp signal.
• The combination meter indicates low tire pressure warning judged with the low tire pressure warning lamp
signal received from the BCM.
For details, refer to
FUEL FILLER CAP WARNING
• The combination meter receives remaining fuel filler cap warning display signal from the ECM with CAN
communication line.
• The combination meter indicates fuel filler cap warning when receiving remaining fuel filler cap warning dis-
play signal.
• The combination meter indicates fuel filler cap warning judged with the fuel filler cap warning display signal
received from the ECM.
For details, refer to
EC-46, "FUEL FILLER CAP WARNING SYSTEM : System Description"
DOOR OPEN WARNING
• The combination meter indicates the door open warning judged by each door switch signal received from the
BCM via CAN communication line.
TRUNK OPEN WARNING
• The combination meter indicates the trunk open warning judged by trunk switch signal received from the
BCM via CAN communication line.
INSTANTANEOUS FUEL CONSUMPTION
• The combination meter receives the fuel consumption monitor signal from the ECM and the vehicle speed
signal from the ABS actuator and electric unit (control unit) via CAN communication.
• The combination meter calculates instantaneous fuel consumption according to the fuel consumption moni-
tor signal and the vehicle speed signal received via CAN communication.
AVERAGE FUEL CONSUMPTION
• The combination meter receives the fuel consumption monitor signal from the ECM and the vehicle speed
signal from the ABS actuator and electric unit (control unit) via CAN communication.
• The combination meter calculates the average fuel consumption according to the fuel consumption monitor
signal and the vehicle speed signal received via CAN communication.
• The average fuel consumption displayed on the information display is uploaded in approximately 30-second
intervals.
NOTE:
When turning ON the ignition switch after triggering a reset or removing/installing the battery, “
−−−−
” is indi-
cated until 30-seconds/500 m (0.31 miles) of driving.
AVERAGE VEHICLE SPEED
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
• Measures the time while the ignition switch is ON through the combination meter.
• The combination meter the average vehicle speed according to the above signals.
• The average vehicle speed displayed on the information display is uploaded in approximately 30-second
intervals.
JSNIA0033GB
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
METER SYSTEM
MWI-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
When turning ON the ignition switch after triggering a reset or removing/installing the battery, “
−−−−
” is indi-
cated until 30 seconds.
TRAVEL TIME
Measures the time while the ignition switch is ON through the combination meter.
TRAVEL DISTANCE
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
• The combination meter calculates the vehicle distance according to the vehicle speed signal. The vehicle
distance is displayed.
POSSIBLE DRIVING DISTANCE
The combination meter calculates possible driving distance according to the vehicle speed signal and fuel
consumption monitor signal transmitted via CAN communication and the fuel level sensor signal transmitted
from the fuel level sensor.
NOTE:
• When turning ON the ignition switch after removing/installing the battery, “
−−−−
” is indicated until 30 sec-
onds.
• The indicated values may not match each other when refueling with the ignition switch ON. Refer to
"INFORMATION DISPLAY : Description"
AMBIENT AIR TEMPERATURE
• The combination meter receives the ambient sensor signal from the ambient sensor.
• The combination meter calculates the ambient temperature according to the ambient sensor signal.
• The indicated temperature does not increase if the vehicle speed is less than 20 km/h (12 MPH).
NOTE:
• The ambient sensor input value that is displayed on “Data Monitor” of CONSULT is the value before the cor-
rection. It may not match the indicated temperature on the information display.
• The ambient temperature may be indicated higher than the actual temperature, depending on heat in the
engine, the road surface temperature, and so on.
SETTING
Setting item list
*: Press and hold the switch (1 second or more).
Items
Setting range
Setting unit
Description
ALERT
TIME TO REST
No setting - 6 hours
30 minutes,
[60 minutes]*
Time to rest is displayed on the informa-
tion display if the vehicle reached the set
travel distance.
ICY
ON/OFF
—
Low outside temp is displayed on the in-
formation display if the ambient tempera-
ture is 3
°
C (37
°
F) or less.
MAINTENANCE
ENGINE OIL
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The engine oil replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
OIL FILTER
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The oil filter replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
TIRE
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The tire replacement interval is displayed
on the information display if the vehicle
reached the set distance.
OTHER
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The other replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
DISPLAY
LANGUAGE
ENGLISH/FRANCAIS/
ESPANOL
—
The language setting can be changed.
UNIT
US/METRIC
—
The unit setting can be changed.
DIAL EFFECTS
ON/OFF
—
The dial effects setting can be changed.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-18
< SYSTEM DESCRIPTION >
COMPASS
COMPASS
System Description
INFOID:0000000007565084
DESCRIPTION
• This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
• The inside mirror switch is used to operate the compass.
Switch Operation
• All standard compasses determine direction relative to magnetic north, however, this electronic compass is
designed to display direction relative to true north.
• The difference between magnetic north and true north varies from place to place across the surface of the
earth.
• This electronic compass must be “told” approximately where it is on the earth’s surface so that the magnetic
north reading can be properly converted into a true north display.
• To tell the electronic compass where it’s at, the earth is separated into numbered “Zone Variances”. The
zone variance number in which the compass is to function must be entered into this electronic compass.
• Each zone is magnetically about 4.2
°
wide. Typically, anything under a 22.5
°
total zone change is not noticed
on the electronic compass display. However, if a change over 22.5
°
occurs, a reading may be off by one or
more primary directions.
• On long trips, the vehicle may leave its original zone and enter one or more new zones. Generally, you do
not need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vacation.
The typical driver will not notice any difference on the display within 3 or 4 zones. However, if the vehicle is
“permanently” moved to a new location, it is recommended that the compass zone be reset.
1
: Compass switch
2
: Compass display
SKIB8868E
Press
Compass is turned ON/OFF
Press and hold
(for 3- 9 sec.)
Compass display (2) turns to zone variation change
mode
Press and hold (for more
than 9 sec.)
Compass display turns to calibration mode
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
OPERATION
MWI-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
OPERATION
Switch Name and Function
INFOID:0000000007565085
JSNIA4275ZZ
Switch name
Operation
Description
Meter control switch
Illumination control switch (+) (1)
Press
An illuminance level of the back light of the combination
meter can be adjusted.
Illumination control switch (
−
) (2)
Enter switch (3)
• The information display screen can be switched.
• The item indicated on the information display can be con-
firmed.
Select switch (4)
When plural items are shown on the information display, a
selected item can be changed to the other item.
Trip reset switch (5)
• The trip meter can be switched between A and B.
• Trip meter A/B can be reset by pressing and holding the
trip reset switch.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000007565086
ON BOARD DIAGNOSIS ITEM
The combination meter allows the following diagnosis items with the on-board diagnosis function.
METHOD OF STARTING
1.
Turn ignition switch OFF.
2.
While pressing the trip reset switch (1), turn ignition switch ON.
3.
If the diagnosis function is activated with “trip A” displayed, the
mileage on “trip A” is reset to “0000.0”. (The same way for “trip
B”.)
4.
Make sure that the trip meter displays “0000.0”.
5.
Press the trip reset switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)
6.
The combination meter is turned to self-diagnosis mode.
• Speedometer, tachometer, engine coolant temperature gauge, fuel gauge, and return to zero, simulta-
neously.
• The dot matrix dots on the information display (dot matrix
information display) (1) blink alternately.
Diagnosis item
Drive circuit check
• Speedometer
• Tachometer
• Engine coolant temperature gauge
• Fuel gauge
LCD (liquid crystal dis-
play) check
Information display (dot matrix information
display and segment information display)
JPNIA0743ZZ
JPNIA0766ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• All segments of the information display (segment information
display) (1) are displayed.
NOTE:
• Check the following items when the self-diagnosis mode of the combination meter does not start.
Replace combination meter if the following items are normal.
- Combination meter power supply and ground circuit.
- Meter control switch signal circuit (trip reset switch signal circuit) and meter control switch.
• If any of the dots are not displayed, replace combination meter.
7.
Each meter activates by pressing the trip reset switch.
NOTE:
• If any of the meters or gauges are not activated, replace combination meter.
• The figure is reference.
CONSULT Function
INFOID:0000000007565087
CONSULT APPLICATION ITEMS
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.
SELF DIAG RESULT
.
DATA MONITOR
Display Item List
JSNIA3443ZZ
JSNIA4276ZZ
System
Diagnosis mode
Description
METER/M&A
Self Diagnostic Result
The combination meter checks the conditions and displays memorized errors.
Data Monitor
Displays the combination meter input/output data in real time.
Warning History
Lighting history of the warning lamp and indicator lamp can be checked.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-22
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
X: Applicable
Display item [Unit]
MAIN
SIGNALS
Description
SPEED METER
[km/h]
X
Value of vehicle speed signal received from ABS actuator and electric unit (control
unit) via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.
SPEED OUTPUT
[km/h]
X
Vehicle speed signal value transmitted to other units via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
[km/h or mph]
Odometer signal value transmitted to other units via CAN communication.
TACHO METER
[rpm]
X
Value of the engine speed signal received from ECM via CAN communication.
NOTE:
8191.875 is displayed when the malfunction signal is received.
FUEL METER
[L]
X
Fuel level indicated on combination meter.
W TEMP METER
[
°
C]
X
Value of engine coolant temperature signal is received from ECM via CAN com-
munication.
NOTE:
215 is displayed when the malfunction signal is input.
ABS W/L
[On/Off]
Status of ABS warning lamp detected from ABS warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
VDC/TCS IND
[On/Off]
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
is received from ABS actuator and electric unit (control unit) via CAN communica-
tion.
SLIP IND
[On/Off]
Status of VDC warning lamp detected from VDC warning lamp signal received
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
[On/Off]
Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
NOTE:
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L
[On/Off]
Status of door warning detected from door switch signal received from BCM via
CAN communication.
TRUNK/GLAS-H
[On/Off]
Status of trunk warning detected from trunk switch signal received from BCM via
CAN communication.
HI-BEAM IND
[On/Off]
Status of high beam indicator lamp detected from high beam request signal is re-
ceived from BCM via CAN communication.
TURN IND
[On/Off]
Status of turn indicator lamp detected from turn indicator signal is received from
BCM via CAN communication.
LIGHT IND
[On/Off]
Status of light indicator lamp detected from position light request signal is received
from BCM via CAN communication.
OIL W/L
[On/Off]
Status of oil pressure warning lamp detected from oil pressure switch signal is re-
ceived from BCM via CAN communication.
MIL
[On/Off]
Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.
CRUISE IND
[On/Off]
Status of CRUISE indicator detected from ASCD status signal is received from
ECM via CAN communication.
O/D OFF IND
[On/Off]
Status of O/D OFF indicator detected from O/D OFF indicator signal is received
from CVT shift selector.
4WD W/L
[On/Off]
Status of AWD warning lamp detected from AWD warning lamp signal is received
from AWD control unit via CAN communication.
4WD LOCK IND
[On/Off]
Status of AWD LOCK warning lamp detected from AWD LOCK warning lamp sig-
nal is received from AWD control unit via CAN communication.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FUEL W/L
[On/Off]
Low-fuel warning lamp status detected by the identified fuel level.
WASHER W/L
[On/Off]
Status of washer warning lamp judged from washer level switch input to combina-
tion meter.
AIR PRES W/L
[On/Off]
Status of low tire pressure warning lamp detected from TPMS malfunction warning
lamp signal is received from BCM via CAN communication.
KEY G/W W/L
[On/Off]
Status of key warning lamp (G/Y) detected from key warning signal is received
from BCM via CAN communication.
LCD
[B&P N, B&P I, ID NG, ROTAT, SFT
P, INSRT, BATT, NO KY, OUTKY, LK
WN]
Displays status of Intelligent Key system warning detected from meter display sig-
nal is received from BCM via CAN communication.
SHIFT IND
[P, R, N, D, L]
Status of shift position indicator detected from shift position signal is received from
TCM via CAN communication.
FUEL CAP W/L
[On/Off]
Status of fuel filler cap warning display detected from fuel filler cap warning display
signal received from ECM via CAN communication.
O/D OFF SW
[On/Off]
Status of O/D OFF switch.
M RANGE SW
[Off]
This item is displayed, but cannot be monitored.
NM RANGE SW
[Off]
This item is displayed, but cannot be monitored.
AT SFT UP SW
[Off]
This item is displayed, but cannot be monitored.
AT SFT DWN SW
[Off]
This item is displayed, but cannot be monitored.
PKB SW
[On/Off]
Status of parking brake switch.
BUCKLE SW
[On/Off]
Status of seat belt buckle switch (driver side).
BRAKE OIL SW
[On/Off]
Status of brake fluid level switch.
A/C AMP CONN
[On/Off]
Status of A/C auto amp. connection recognition signal.
ENTER SW
[On/Off]
Status of
(ENTER) switch.
SELECT SW
[On/Off]
Status of
(SELECT) switch.
DISTANCE
[km]
Value of possible driving distance calculated by combination meter.
OUTSIDE TEMP
[
°
C or
°
F]
Ambient air temperature value converted from ambient sensor signal received
from ambient sensor.
NOTE:
This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient
sensor input value.)
FUEL LOW SIG
[On/Off]
Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.
BUZZER
[On/Off]
X
Buzzer status (in the combination meter) is detected from the buzzer output signal
received from each unit via CAN communication and the warning output condition
of the combination meter.
TPMS PRESS L
[On/Off]
Status of check low tire pressure warning detected from low tire pressure warning
lamp signal received from BCM via CAN communication.
Display item [Unit]
MAIN
SIGNALS
Description
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-24
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
NOTE:
Some items are not available according to vehicle specification.
WARNING HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “WARNING HISTORY” indicates the “TIME” when the warning/indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO WARNING HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• WARNING HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
NOTE:
In items displayed on the CONSULT screen, only those listed in the above table are used.
Display item
Description
ABS W/L
Lighting history of ABS warning lamp.
VDC/TCS IND
Lighting history of VDC OFF indicator lamp.
SLIP IND
Lighting history of VDC warning lamp.
BRAKE W/L
Lighting history of brake warning lamp.
DOOR W/L
Lighting history of door warning.
TRUNK/GLAS-H
Lighting history of trunk warning.
OIL W/L
Lighting history of oil pressure warning lamp.
C-ENG W/L
Lighting history of malfunction indicator lamp.
CRUISE IND
Lighting history of CRUISE indicator lamp.
SET IND
Lighting history of SET indicator.
O/D OFF IND
Lighting history of O/D OFF indicator lamp.
4WD W/L
Lighting history of AWD warning lamp.
FUEL W/L
Lighting history of low fuel level warning.
WASHER W/L
Lighting history of low washer fluid warning
AIR PRES W/L
Lighting history of low tire pressure warning lamp.
KEY G/Y W/L
Lighting history of key warning lamp (green/yellow).
KEY R W/L
Lighting history of key warning lamp (red).
CHAGE W/L
Lighting history of charge warning lamp.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
COMBINATION METER
MWI-25
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ECU DIAGNOSIS INFORMATION
COMBINATION METER
Reference Value
INFOID:0000000007565088
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
SPEED METER
[km/h]
Ignition switch
ON
While driving
Equivalent to speedometer reading
NOTE:
655.35 is displayed when the malfunc-
tion signal is received
SPEED OUTPUT
[km/h]
Ignition switch
ON
While driving
Equivalent to speedometer reading
NOTE:
655.35 is displayed when the malfunc-
tion signal is received
ODO OUTPUT
[km/h or mph]
Ignition switch
ON
—
Equivalent to odometer reading in
combination meter
TACHO METER
[rpm]
Ignition switch
ON
While driving
Equivalent to tachometer reading
NOTE:
8191.875 is displayed when the mal-
function signal is received
FUEL METER
[L]
Ignition switch
ON
—
Values according to fuel level
W TEMP METER
[
°
C]
Ignition switch
ON
—
Values according to engine coolant
temperature
NOTE:
215 is displayed when the malfunction
signal is input
ABS W/L
Ignition switch
ON
ABS warning lamp ON
On
ABS warning lamp OFF
Off
VDC/TCS IND
Ignition switch
ON
VDC OFF indicator lamp ON
On
VDC OFF indicator lamp OFF
Off
SLIP IND
Ignition switch
ON
VDC warning lamp ON
On
VDC warning lamp OFF
Off
BRAKE W/L
Ignition switch
ON
Brake warning lamp ON
On
Brake warning lamp OFF
Off
DOOR W/L
Ignition switch
ON
Door warning ON
On
Door warning OFF
Off
TRUNK/GLAS-H
Ignition switch
ON
Trunk warning ON
On
Trunk warning OFF
Off
HI-BEAM IND
Ignition switch
ON
High-beam indicator lamp ON
On
High-beam indicator lamp OFF
Off
TURN IND
Ignition switch
ON
Turn signal indicator lamp ON
On
Turn signal indicator lamp OFF
Off
LIGHT IND
Ignition switch
ON
Light indicator lamp ON
On
Light indicator lamp OFF
Off
OIL W/L
Ignition switch
ON
Oil pressure warning lamp ON
On
Oil pressure warning lamp OFF
Off
MIL
Ignition switch
ON
Malfunction indicator lamp ON
On
Malfunction indicator lamp OFF
Off
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст