Murano Cross Cabriolet Z51 (2012 year). Manual — part 83
SR-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SR
A
B
SR
N
O
P
CONTENTS
SRS AIRBAG
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
Occupant Classification System . . . . . . . ..
Service . . . . . . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ....
BASIC INSPECTION . . . . . . . . .
COLLISION DIAGNOSIS . . . . . . . . .
FOR FRONTAL COLLISION . . . . . . . . . ...
FOR FRONTAL COLLISION : When SRS is acti-
vated in a collision . . . . . . . . . . . . .....
FOR FRONTAL COLLISION : When SRS is not
activated in a collision . . . . . . . . . . . ...
FOR SIDE AND ROLLOVER COLLISION . . . . ..
FOR SIDE AND ROLLOVER COLLISION : When
SRS is activated in a collision . . . . . . . . ...
FOR SIDE AND ROLLOVER COLLISION : When
SRS is not activated in a collision . . . . . . .....
REMOVAL AND INSTALLATION . . . ...
DRIVER AIR BAG MODULE . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SPIRAL CABLE . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT PASSENGER AIR BAG MODULE . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR-MOUNTED CURTAIN AIR BAG MOD-
ULE . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
POP-UP ROLL BAR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CRASH ZONE SENSOR . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SATELLITE SENSOR . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DIAGNOSIS SENSOR UNIT . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT SEAT BELT PRE-TENSIONER . . ...
Removal and Installation . . . . . . . . . . .
OCCUPANT CLASSIFICATION SYSTEM
CONTROL UNIT . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2013 February
2012 Murano CrossCabriolet
SR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007566523
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007566524
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution for Battery Service
INFOID:0000000007566525
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Occupant Classification System
INFOID:0000000007566526
• Replace occupant classification system control unit and passenger front seat cushion as an assembly.
SE-39, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
PRECAUTIONS
SR-3
< PRECAUTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Service
INFOID:0000000007566527
• Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
For approximately 3 minutes or more after the cables are removed, it is still possible for the air bag and seat
belt pre-tensioner to deploy. Therefore, never work on any SRS connectors or wires until at least 3 minutes
have elapsed.
• Diagnosis sensor unit must always be installed with their arrow marks “
⇐
” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
• The spiral cable must be aligned in the neutral position since its rotations are limited. Never turn steering
wheel and column after removal of steering gear.
• Handle air bag module carefully. Always place driver and passenger air bag modules with the pad side fac-
ing upward and seat mounted side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following passenger air bag deployment.
• Never allow harness to come in contact with oil, grease, waste oil, or water.
• Never insert foreign materials, such as a screwdriver, into the harness connector. (This is to prevent acci-
dental activation caused by static electricity.)
• Never enter in the deployment area of pop-up roll bar. Never put an object in the deployment area of pop-up
roll bar. (This is to prevent an unintentional deployment.)
• When handling pop-up roll bar, always grip frame and handle carefully.
• Never reuse pop-up roll bar that is deployed once.
• Modification of pop-up roll bar may cause unintentional deployment or a malfunction. Never disassemble or
apply modification to the pop-up roll bar. (Non-disassembly)
• Never apply impact to pop-up roll bar by dropping or others. Always replace if an impact is applied.
• When repairing surrounding area of pop-up roll bar, be careful not to apply over voltage of welding and oth-
ers. Remove pop-up roll bar in advance if necessary. Be careful for modification of mounting area or installa-
tion of other parts because these may cause damage or a malfunction.
• Never disassemble the pop-up roll bar.
• Never expose the pop-up roll bar to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the pop-up roll bar.
Revision: 2013 February
2012 Murano CrossCabriolet
SR-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000007566528
Tool name
Description
Tamper resistant TORX bit
Removes driver air bag module
Remover tool
Removes clips, pawls, and metal clip
S-NT757
JMKIA3050ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
COLLISION DIAGNOSIS
SR-5
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
BASIC INSPECTION
COLLISION DIAGNOSIS
FOR FRONTAL COLLISION
FOR FRONTAL COLLISION : When SRS is activated in a collision
INFOID:0000000007566529
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Replace the diagnosis sensor unit.
3.
Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies.
4.
Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
5.
Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner
assemblies.
6.
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to
for details. Ensure entire SRS operates properly.
7.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-13, "On Board Diagnosis Function"
SRS INSPECTION (FOR FRONTAL COLLISION)
Part
Inspection
Driver air bag module
If the driver air bag has deployed:
REPLACE
Install with new fasteners.
Front passenger air bag module
(if equipped)
If the front passenger air bag has deployed:
REPLACE
Install with new fasteners.
Crash zone sensor
If any of the front air bags or seat belt pre-tensioners* have been activated:
REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Diagnosis sensor unit
If any of the SRS components have been activated:
REPLACE the diagnosis sensor unit.
Install with new fasteners.
Steering wheel
1.
Visually check steering wheel for deformities.
2.
Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
3.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4.
Check steering wheel for excessive free play.
5.
If no damage is found, reinstall.
6.
If damaged
−
REPLACE.
Spiral cable
If the driver front air bag has deployed:
REPLACE the spiral cable.
Occupant classification system
(Passenger seat)
1.
Remove passenger seat assembly.
2.
Check control unit case for dents, cracks of deformities.
3.
Check connectors and pressure sensor tube for damage, and terminals for deformities.
4.
Check seat frame and cushion pan for dents or deformities.
5.
If no damage is found, reinstall seat with new fasteners.
6.
If damaged
−
REPLACE seat cushion assembly with new fasteners.
Revision: 2013 February
2012 Murano CrossCabriolet
SR-6
< BASIC INSPECTION >
COLLISION DIAGNOSIS
FOR FRONTAL COLLISION : When SRS is not activated in a collision
INFOID:0000000007566530
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
3.
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to
for details. Ensure entire SRS operates properly.
4.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-13, "On Board Diagnosis Function"
SRS INSPECTION (FOR FRONTAL COLLISION)
Harness and connectors
1.
Check connectors for poor connection, damage, and terminals for deformities.
2.
Check harness for binding, chafing, cuts, or deformities.
3.
If no damage is found, reinstall the harness and connectors.
4.
If damaged
−
REPLACE the damaged harness. Do not attempt to repair, splice or modify any
SRS harness.
Instrument panel assembly
If the front passenger air bag has deployed:
REPLACE the instrument panel assembly. (integrated type)
Part
Inspection
Part
Inspection
Driver air bag module
If the driver air bag has NOT been deployed:
1.
Remove driver air bag module. Check harness cover and connectors for damage, terminals for
deformities, and harness for binding.
2.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install driver air bag module with new fasteners.
Front passenger air bag module
(if equipped)
If the front passenger air bag has NOT been deployed:
1.
Remove front passenger air bag module. Check harness cover and connectors for damage, ter-
minals for deformities, and harness for binding.
2.
Install front passenger air bag module into the instrument panel to check fit with the instrument
panel.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install front passenger air bag modules with new fasteners.
Crash zone sensor
If the front air bags or seat belt pre-tensioners have NOT been activated:
1.
Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.
2.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor
and bracket.
3.
Install the crash zone sensor to check fit.
4.
If no damage is found, reinstall with new fasteners.
5.
If damaged
−
REPLACE the crash zone sensor and bracket with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If the pre-tensioners have NOT been activated:
1.
Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
2.
Check belts for damage and anchors for loose mounting.
3.
Check retractor for smooth operation.
4.
Check seat belt adjuster for damage.
5.
Check for deformities of the center pillar inner.
6.
If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7.
If no damage is found, reinstall seat belt pre-tensioner assembly.
8.
If damaged
−
REPLACE. Install the seat belt pre-tensioners with new fasteners.
Revision: 2013 February
2012 Murano CrossCabriolet
COLLISION DIAGNOSIS
SR-7
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FOR SIDE AND ROLLOVER COLLISION
FOR SIDE AND ROLLOVER COLLISION : When SRS is activated in a collision
INFOID:0000000007566531
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated)
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated)
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies
3.
Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)
4.
Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to
for details. Make sure entire SRS operates properly.
5.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-13, "On Board Diagnosis Function"
Diagnosis sensor unit
If none of the SRS components have been activated:
1.
Check case for dents, cracks or deformities.
2.
Check connectors for damage, and terminals for deformities.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install diagnosis sensor unit with new fasteners.
Steering wheel
1.
Visually check steering wheel for deformities.
2.
Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
3.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4.
Check steering wheel for excessive free play.
5.
If no damage is found, reinstall.
6.
If damaged
−
REPLACE.
Spiral cable
If the driver front air bag has not deployed:
1.
Visually check spiral cable and combination switch for damage.
2.
Check connectors and protective tape for damage.
3.
Check steering wheel for noise, binding or heavy operation.
4.
If no damage is found, reinstall.
5.
If damaged
−
REPLACE.
Occupant classification system
(Passenger seat)
1.
Remove passenger seat assembly.
2.
Check control unit case for dents, cracks of deformities.
3.
Check connectors and pressure sensor tube for damage, and terminals for deformities.
4.
Check seat frame and cushion pan for dents or deformities.
5.
If no damage is found, reinstall seat with new fasteners.
6.
If damaged
−
REPLACE seat cushion assembly with new fasteners.
Harness and connectors
1.
Check connectors for poor connection, damage, and terminals for deformities.
2.
Check harness for binding, chafing, cuts, or deformities.
3.
If no damage is found, reinstall the harness and connectors.
4.
If damaged
−
REPLACE the damaged harness. Do not attempt to repair, splice or modify any
SRS harness.
Instrument panel assembly
If the front passenger air bag has NOT deployed:
1.
Visually check instrument panel assembly for damage.
2.
If no damage is found, reinstall the instrument panel assembly.
3.
If damaged
−
REPLACE the instrument panel assembly.
Part
Inspection
Revision: 2013 February
2012 Murano CrossCabriolet
SR-8
< BASIC INSPECTION >
COLLISION DIAGNOSIS
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision
INFOID:0000000007566532
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag
module must be replaced.
3.
Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to
for details. Make sure entire SRS operates properly.
4.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
.
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
Part
Inspection
Side curtain air bag module LH
If the side curtain air bag LH has deployed:
REPLACE the side curtain air bag module LH.
Install with new fasteners.
Side curtain air bag module RH
If the side curtain air bag RH has deployed:
REPLACE the side curtain air bag module RH.
Install with new fasteners.
Front side air bag module LH
If the front side air bag LH has deployed:
REPLACE front seatback assembly LH.
Front side air bag module RH
If the front side air bag RH has deployed:
REPLACE front seatback assembly RH.
Side air bag (satellite) sensor
(LH or RH)
If any of the SRS components have deployed:
REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.
Diagnosis sensor unit
If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Center inner pillar
1.
Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
2.
If damaged
−
REPAIR the center inner pillar.
Trim/headlining
1.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.
2.
If damaged
−
REPLACE the damaged trim parts.
Door-mounted curtain air bag
module LH
If the door-mounted curtain air bag module LH has deployed:
REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.
Door-mounted curtain air bag
module RH
If the door-mounted curtain air bag module RH has deployed:
REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.
Pop-up roll bar assemblies
If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.
Revision: 2013 February
2012 Murano CrossCabriolet
COLLISION DIAGNOSIS
SR-9
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Part
Inspection
Side curtain air bag module LH
If the side curtain air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.
2.
If damaged
−
Remove the side curtain air bag module LH.
3.
Check for visible signs of damage (tears etc.) of the side curtain air bag module LH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall the side curtain air bag module LH with new fasteners.
6.
If damaged
−
REPLACE the side curtain air bag module LH with new fasteners.
Side curtain air bag module RH
If the side curtain air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.
2.
If damaged
−
Remove the side curtain air bag module RH.
3.
Check for visible signs of damage (tears etc.) of the side curtain air bag module RH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall the side curtain air bag module RH with new fasteners.
6.
If damaged
−
REPLACE the side curtain air bag module RH with new fasteners.
Front side air bag module LH
If the front side air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.
2.
Check harness and connectors for damage, and terminals for deformities.
3.
If damaged
−
REPLACE the front seatback assembly LH.
Front side air bag module RH
If the front side air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.
2.
Check harness and connectors for damage, and terminals for deformities.
3.
If damaged
−
REPLACE the front seatback assembly RH.
Side air bag (satellite) sensor
(LH or RH)
If none of the SRS components have been activated:
1.
Remove the side air bag (satellite) sensor (LH or RH) on the collision side. Check harness con-
nectors for damage, terminals for deformities, and harness for binding.
2.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the side air bag (satellite)
sensor (LH or RH).
3.
Install the side air bag (satellite) sensor (LH or RH) to check fit.
4.
If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasteners.
5.
If damaged
−
REPLACE the side air bag (satellite) sensor (LH or RH) with new fasteners.
Diagnosis sensor unit
If none of the SRS components have been activated:
1.
Check case and bracket for dents, cracks or deformities.
2.
Check connectors for damage, and terminals for deformities.
3.
If no damage is found, reinstall the diagnosis sensor unit with new fasteners.
4.
If damaged
−
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If the pre-tensioners have NOT been activated:
1.
Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
2.
Check belts for damage and anchors for loose mounting.
3.
Check retractor for smooth operation.
4.
Check seat belt adjuster for damage.
5.
Check for deformities of the center pillar inner.
6.
If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7.
If no damage is found, reinstall seat belt pre-tensioner assembly.
8.
If damaged
−
REPLACE. Install the seat belt pre-tensioners with new fasteners.
Seat (with front side air bag)
If the front LH or front RH side air bag modules have NOT deployed:
1.
Visually check the seat on the collision side.
2.
Remove the seat on the collision side and check the following for damage and deformities.
-
Harness, connectors and terminals
-
Frame and recliner (for front and rear seat), and also adjuster and slides (for front seat)
3.
If no damage is found, reinstall the seat.
4.
If damaged
−
REPLACE the damaged seat parts using new fasteners. If the front seat back is
damaged, the front seat back assembly must be replaced.
Center inner pillar
1.
Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
2.
If damaged
−
REPAIR the center inner pillar.
Revision: 2013 February
2012 Murano CrossCabriolet
SR-10
< BASIC INSPECTION >
COLLISION DIAGNOSIS
Trim/headlining
1.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.
2.
If damaged
−
REPLACE the damaged trim parts.
Door-mounted curtain air bag
module LH
If the door-mounted curtain air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.
2.
If damaged
−
REPLACE the door finisher LH with new fasteners.
3.
Check for visible signs of damaged (tears etc.) of the door-mounted curtain air bag module LH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall door finisher.
CAUTION:
When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.
6.
If damaged
−
REPLACE the door finisher LH and door-mounted curtain air bag module LH with
new fasteners.
Door-mounted curtain air bag
module RH
If the door-mounted curtain air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.
2.
If damaged
−
REPLACE the door finisher RH with new fasteners.
3.
Check for visible signs of damage (tears etc.) of the door-mounted curtain air bag module RH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall door finisher.
CAUTION:
When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.
6.
If damaged
−
REPLACE the door finisher RH and door-mounted curtain air bag module RH with
new fasteners.
Pop-up roll bar
If the pop-up roll bar has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the pop-up roll bar.
2.
If damaged
−
REPLACE the pop-up roll bar with new fasteners.
3.
Check harness and connectors for damage, and terminals for deformities.
4.
If no damage is found, reinstall the pop-up roll bar with new fasteners.
5.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the seatback support
brace assembly.
6.
If damaged
−
REPAIR the seatback support brace assembly.
Part
Inspection
Revision: 2013 February
2012 Murano CrossCabriolet
DRIVER AIR BAG MODULE
SR-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Exploded View
INFOID:0000000007566533
Removal and Installation
INFOID:0000000007566534
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove side lids (LH and RH).
2.
Remove TORX bolts (LH and RH) from steering wheel (1) lower
side using TORX bit (A).
3.
Pull out driver air bag module.
1.
Steering wheel
2.
Driver air bag module
3.
Side lid (LH/RH)
4.
TORX bolt (LH/RH)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMHIA0503GB
JMHIA0265ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
SR-12
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
4.
Disconnect driver air bag harness connector.
CAUTION:
• For installing/removing the driver air bag harness connec-
tor, insert thin screwdriver wrapped in tape into notch, lift
lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
5.
Remove driver air bag module.
CAUTION:
• Always place the driver air bag module with pad side facing
upward.
• Never impact the driver air bag module.
• Replace the driver air bag module if it is dropped or sustains
an impact.
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolts after removal, replace with new bolts.
• Fix the driver air bag harness to the harness fixing hook (A).
PHIA0953J
: Upward
JMHIA0504ZZ
JMHIA0009ZZ
JMHIA0505ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
DRIVER AIR BAG MODULE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Tighten the TORX bolts after completely adjusting the centers of fixing holes on the driver air bag
module side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged
and the module is not installed securely.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2013 February
2012 Murano CrossCabriolet
SR-14
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
SPIRAL CABLE
Exploded View
INFOID:0000000007566535
Removal and Installation
INFOID:0000000007566536
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
2.
Remove steering wheel. Refer to
ST-30, "Removal and Installation"
.
3.
Remove steering column cover (upper/lower). Refer to
.
4.
Disconnect spiral cable and steering angle sensor harness con-
nectors (A).
NOTE:
Disconnect spiral cable and steering angle sensor body side
harness connectors after removing the spiral cable.
5.
Remove spiral cable fixing screws.
1.
Steering column cover (upper)
2.
Spiral cable
3.
Steering column cover (lower)
4.
Steering column assembly
A
: Driver air bag harness connector
JMHIA0506ZZ
JMHIA0507ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
6.
Remove spiral cable side pawls (A).
7.
Pull out forward spiral cable.
8.
Remove steering angle sensor. Refer to
BRC-105, "Removal and Installation"
.
CAUTION:
• Never impact the spiral cable.
• Never impact the spiral cable by dropping, etc. Replace the
spiral cable if it is dropped or sustains an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as per the following.
• Turn carefully the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond number of turns
required. (This will cause the cable to snap.)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
JMHIA0508ZZ
JMHIA0009ZZ
JMHIA0657ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст