Qashqai J11. Driver assistance system — part 7
DAS
CAMERA AIMING ADJUSTMENT
DAS-97
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
1.
Mark points “A”, “B”, “C” and “D”at the center of the lateral sur-
face of each wheels.
NOTE:
Hang a string with a cone from the fender so as to pass through
the center of wheel, and then mark a point at the center of the
lateral surface of the wheel.
2.
Draw line “LH” passing through points “A” and “B” on the left side
of vehicle.
NOTE:
Approximately 4 m (13.12 ft) or more from the front end of vehi-
cle.
3.
Mark point “E” on the line “LH” at the positions 2800 mm (110.24
in) from point “A”.
4.
Draw line “RH” passing through points “C” and “D” on the right side of vehicle in the same way as step 2.
5.
Mark point “F” on the line “RH” at the positions 2800 mm (110.24 in) from point “C”.
6.
Draw line “FW” passing through the points “E” and “F” on the front side of vehicle.
7.
Mark point “X” at the center of point “E” and “F” on the line “FW”.
CAUTION:
Make sure that “E” to “X” is equal to “F” to “X”.
8.
Position the center of the right target and left target to point of “X”.
>> Proceed to
DAS-98, "Work Procedure (Camera Aiming Adjustment)"
.
“A” – “E” (“C” – “F”)
: 2800 mm (110.24 in)
PKIB4694E
JSOIA1043GB
JMOIA0063GB
DAS-98
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CAMERA AIMING ADJUSTMENT
Work Procedure (Camera Aiming Adjustment)
INFOID:0000000010609511
CAUTION:
Perform the adjustment under unloaded vehicle condition.
1.
CHECK VEHICLE HEIGHT
Measure both side of front wheelarch height (Hf). Then calculate
“Dh”.
CAUTION:
Be sure to measure wheelarch height correctly.
NOTE:
“Dh” may be calculated as a minus value.
>> GO TO 2.
2.
CAMERA AIMING ADJUSTMENT
With CONSULT
CAUTION:
Operate CONSULT outside the vehicle, and close all the doors. (To retain vehicle attitude appropri-
ately)
1.
Select “Work Support” on “LANE CAMERA” with CONSULT.
2.
Select “AUTO AIM”.
3.
Confirm the following items;
-
The target should be accurately placed.
-
The vehicle should be stopped.
4.
Select “Start” to perform camera aiming.
CAUTION:
• Never select “Start” when the target is not accurately placed.
• Wait 5 seconds or more after selecting “Start”.
5.
Input the following parameters, and then select “Start”.
-
Htu: 1501 (mm)
-
Htl: 1299 (mm)
-
Dt: 2800 (mm)
-
Ts: 101 (mm)
-
Dbt: 956 (mm)
-
VP: 2 (RHD models for Europe)/4 (LHD models for Europe)/6 (for Russia)/7 (for Australia)
6.
Confirm the displayed item.
Is “Normally Completed” displayed?
YES
>> Select “End” to close the aiming adjustment procedure. Then GO TO 4.
NO
>> GO TO 3.
3.
INCOMPLETE CAUSE CONFIRMATION
1.
Perform the following services according to the displayed message.
Dh [mm] = (Hfl + Hfr)
÷
2
−
763
where,
Hfl: Front left wheelarch height [mm]
Hfr: Front right wheelarch height [mm]
JSOIA1046GB
Displayed message
Possible cause
Service procedure
Stop
—
Temporary malfunction in internal pro-
cessing of the front camera unit.
Go back to step 1.
00H Routine not acti-
vated
Front camera unit malfunction.
Position the target appropriately again.
Then perform the aiming again.
10H Writing error
• Temporary malfunction in internal
processing of the front camera unit.
• Front camera unit malfunction.
DAS
CAMERA AIMING ADJUSTMENT
DAS-99
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
NOTE:
Replace camera unit if “00H Routine not activated” or “Writing error is detected.” are repeatedly indicated
during the above two services are performed.
2.
Confirm that “Normally completed” is displayed and then select “End” to close the adjustment procedure.
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis of front camera unit with CONSULT.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
NO
>> WORK END
Work Procedure (Target Mark Sample)
INFOID:0000000010609512
Adjust the scale so that the item is the same size as the following, and print.
• Target length (L): 202 mm
• Target width (W): 303 mm
CAUTION:
• Never allow a clearance on the black and white boundary.
0 – 16
—
• A target is not -yet-placed.
(Front camera unit cannot detect the
target.)
• The position of the targets is not cor-
rect.
• The position of the front camera unit
is not correct.
• Inappropriate work environment.
• Inappropriate vehicle condition.
• Input value is not correct against ac-
tual setting position.
Position the target appropriately again.
Then perform the aiming again.
Abnormally complet-
ed.
—
Displayed message
Possible cause
Service procedure
DAS-100
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CAMERA AIMING ADJUSTMENT
• Never apply tape to target surface.
JSOIA0633ZZ
DAS
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
DAS-101
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
Description
INFOID:0000000010619788
• Always perform the rear camera calibration after removing and installing or replacing the rear camera.
• Always perform the rear camera calibration after replacing the around view monitor control unit.
CAUTION:
• Place the vehicle on level ground when the calibration is operated.
• Follow the CONSULT when performing the calibration. (Rear camera calibration cannot be operated
without CONSULT.)
Work Procedure (Preparation)
INFOID:0000000010619789
1.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the camera control unit with CONSULT (AVM).
Is any DTC detected?
Except “U1308”>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
.
“U1308” or no DTC>>GO TO 2.
2.
PREPARATION BEFORE REAR CAMERA CALIBRATION
1.
Perform pre-inspection for diagnosis. Refer to
DAS-82, "Inspection Procedure"
.
2.
Adjust the tire pressure to the specified pressure value.
3.
Maintain no-load in vehicle.
4.
Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5.
Shift the selector lever to “P” position and release the parking brake.
6.
Clean the rear camera.
>> GO TO 3.
3.
PREPARATION OF CALIBRATION TARGET MARK
1.
Prepare six sheets of white paper and black paper, respectively, with dimensions of 250 mm (9.84 in)
×
250 mm (9.84 in) to create a left target, right target, and center target.
NOTE:
Correct the magnification of print and print the target mark sample in the service manual on the blackpa-
per. Refer to
DAS-105, "Work Procedure (Target Mark Sample)"
2.
Tape two sheets of black paper and two sheets of white paper
together to make a target of 500 mm (19.69 in)
×
500 mm (19.69
in).
NOTE:
Use a transparent tape.
3.
Create two more targets according to step 2.
W
:250 mm (9.84 in)
L
:250 mm (9.84 in)
JSOIA0635ZZ
DAS-102
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
>> Refer to
DAS-102, "Work Procedure (Target Setting)"
Work Procedure (Target Setting)
INFOID:0000000010619790
CAUTION:
• Perform this operation in a horizontal position where there is a clear view for 3 m (9.84 ft) backward
and 4 m (13.12 ft) wide.
• Place the target in a well-lighted location. (Poor lighting may make it hard to adjust.)
• The target may not be detected when it shines by the reflected light of the sun or lighting.
• The target may not be detected when there is the same pattern of black and white as the target when
the pattern is within 0.5 m (1.64 ft) from either side and upward/downward position from the target. (It
is desirable that the target is positioned on the single-color floor.)
1.
TARGET SETTING
W
1
:250 mm (9.84 in)
W
2
:500 mm (19.69 in)
L
1
:250 mm (9.84 in)
L
2
:500 mm (19.69 in)
Left target and right target
Center target
JSOIA0630ZZ
JSOIA1098GB
DAS
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
DAS-103
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
1.
Mark points “A”, “B”, “C” and “D” at the center of the lateral sur-
face of each wheel.
NOTE:
Hang a string with a cone from the fender so as to pass through
the center of wheel, and then mark a point at the center of the
lateral surface of the wheel.
2.
Draw line “LH” passing through points “A” and “B” on the left side
of vehicle.
NOTE:
Approximately 2.2 m (7.22 ft) or more at the rear from the rear
axle.
3.
Mark point “E” on the line “LH” at the positions 1,854 mm (72.99
in) from point “B”.
4.
Draw line “RH” passing through points “C” and “D” on the right side of vehicle in the same way as step 2.
NOTE:
Approximately 2.2 m (7.22 ft) or more at the rear from the rear axle.
5.
Mark point E on the line “RH” at the positions 1,854 mm (72.99 in) from point “D”.
6.
Draw line “RW” passing through the points “E” and “F” on the rear of vehicle.
NOTE:
Approximately 1.8 m (5.91 ft) or more at both left and right sides from vehicle center.
7.
Mark point “Ct” at the center of point “E” and “F” on the line “RW”.
CAUTION:
Make sure that “E” to “Ct” is equal to “F” to “Ct”.
8.
Mark point “Lt” and “Rt” on the line “RW” at the positions 1,450 mm (57.09 in) from point “Ct”.
9.
Position the center of the target mark to point of “Ct”, “Lt” and “Rt”.
CAUTION:
To perform an accurate calibration, check that the black-and-white pattern is as shown in the fig-
ure. The pattern of the center target differs from that of right/left target.
Distance between B and E
: 1,854 mm (72.99 in)
Distance between D and F
: 1,854 mm (72.99 in)
Distance W1
: 1,450 mm (57.09 in)
Distance W2
: 1,450 mm (57.09 in)
Distance L
: 1,854 mm (72.99 in)
W1
: 1,450 mm (57.09 in)
W2
: 1,450 mm (57.09 in)
L
: 1,854 mm (72.99 in)
PKIB7667E
JSOIA1097GB
DAS-104
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
>> Refer to
DAS-104, "Work Procedure (Rear Camera Calibration)"
Work Procedure (Rear Camera Calibration)
INFOID:0000000010619791
CAUTION:
For accuracy, perform the calibration under the specified vehicle condition (Fuel full, no-load, speci-
fied tire pressure, etc.). Refer to
DAS-101, "Work Procedure (Preparation)"
1.
CHECK REAR CAMERA HEIGHT
Measure the rear camera height.
H:Rear camera height.
>> GO TO 2.
2.
REAR CAMERA CALIBRATION
1.
Select “Work Support” on “AVM” with CONSULT.
2.
Select “REAR CAMERA ITS” and then touch “Start”.
3.
Touch“OK”.
4.
Input the rear camera height “H”, and then touch “APPLY”.
5.
Confirm that the same value is displayed on the center display.
6.
Confirm the following items;
-
The target should be accurately placed.
-
The vehicle should be stopped.
-
The vehicle should be under the specified vehicle condition.
7.
Select “Start” to perform camera aiming.
CAUTION:
To properly maintain vehicle attitude, operate CONSULT outside the vehicle with all the doors
closed.
8.
Confirm the displayed item.
-
“Completed”: Select “Completion”.
-
“Not completed”: Perform the following services.
JSOIA0634ZZ
DAS
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
DAS-105
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
>> GO TO 3.
3.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of around view monitor control unit with CONSULT (AVM).
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
NO
>> GO TO 4.
4.
ACTION TEST
Test the BSW system operation by action test. Refer to
>> WORK END
Work Procedure (Target Mark Sample)
INFOID:0000000010619792
NOTE:
Displayed item
Code
Possible causes
Service procedure
Check the error contents
using the screen of naviga-
tion system.
11
• A target is not-yet-placed. (Center)
• Target mark reflects the light. (Center)
• Position the target appropriately again. (Center)
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark.
(Center)
12
• A target is not-yet-placed. (Right)
• Target mark reflects the light. (Right)
• Position the target appropriately again. (Right)
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark.
(Right)
13
• A target is not-yet-placed. (Left)
• Target mark reflects the light. (Left)
• Position the target appropriately again. (Left)
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark. (Left)
21
A target is dirty. (Center)
Clean target mark. (Center)
22
A target is dirty. (Right)
Clean target mark. (Right)
23
A target is dirty. (Left)
Clean target mark. (Left)
51
• The position of the target is not correct.
(Center)
• Target mark reflects the light. (Center)
• The position of the rear camera is not
correct.
• Set target mark direction as shown in the figure.
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark.
(Center)
• Install rear camera properly
52
• The position of the target is not correct.
(Right)
• Target mark reflects the light. (Right)
• The position of the rear camera is not
correct.
• Set target mark direction as shown in the figure.
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark.
(Right)
• Install rear camera properly
53
• The position of the target is not correct.
(Left)
• Target mark reflects the light. (Left)
• The position of the rear camera is not
correct.
• Set target mark direction as shown in the figure.
DAS-102, "Work Procedure (Target
• Shut out the light reflecting on target mark. (Left)
• Install rear camera properly
DAS-106
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
Change the magnification of print to 250 mm (9.84 in)
×
250 mm (9.84 in) and print the target mark sample.
JSOIA0633ZZ
DAS
ACTION TEST
DAS-107
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ACTION TEST
LDW
LDW : Description
INFOID:0000000010416827
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Lane Departure Warning"
.
LDW : Inspection Procedure
INFOID:0000000010416828
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Lane Departure Warning"
.
1.
CHECK LDW SYSTEM SETTING
1.
Start the engine.
2.
Check that the LDW system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR LDW
1.
Enable the setting of the LDW system on the vehicle information display.
2.
Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation
Action
LDW ON indi-
cator
Indication on the combination
meter
Buzzer
Less than
Approx. 55
km/h (34
MPH)
Close to lane marker
No action
ON
White
OFF
JSOIA1422ZZ
DAS-108
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 55 km/h (34 MPH). Refer to
DAS-15, "LDW : System Description"
>> Inspection End.
BSW
BSW : Description
INFOID:0000000010416829
• Perform action test to verify the customer
′
s concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for BSW: Refer to
DAS-17, "BSW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Blind Spot Warning"
BSW : Inspection Procedure
INFOID:0000000010416830
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for BSW: Refer to
DAS-17, "BSW : System Description"
- Handling precaution: Refer to
DAS-31, "Precautions for Blind Spot Warning"
1.
CHECK BSW SYSTEM SETTING
1.
Start the engine.
2.
Check that the BSW system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR BSW
1.
Enable the setting of the BSW system on the vehicle information display.
2.
Check the BSW operation according to the following table.
Approx. 60
km/h (37
MPH) or
more
Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks
ON
OFF (orange) Blink
Short contin-
uous beeps
• Close to lane marker
• Turn signal ON (Deviate
side)
No action
ON
White
OFF
Vehicle condition/ Driver's operation
Action
LDW ON indi-
cator
Indication on the combination
meter
Buzzer
JSOIA1367ZZ
JSOIA1422ZZ
DAS
ACTION TEST
DAS-109
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Vehicle condition/Driver
′
s operation
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 29 km/h (18 MPH). Refer to
DAS-17, "BSW : System Description"
.
>> Inspection End.
MOD
MOD : Description
INFOID:0000000010416831
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for MOD: Refer to
DAS-22, "MOD : System Description"
MOD : Inspection Procedure
INFOID:0000000010416832
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- System description for MOD: Refer to
DAS-22, "MOD : System Description"
1.
CHECK MOD SYSTEM SETTING
1.
Start the engine.
2.
Check that the MOD system setting can be enabled/disabled on the vehicle information display.
3.
Turn OFF the ignition switch and wait for 30 seconds or more.
4.
Check that the previous setting is saved when the engine starts again.
Warning
systems
ON
indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Turn signal
condition
Status of vehi-
cle detection
within detec-
tion area
Indication on the combination
meter
Buzzer
ON
Less than Ap-
prox. 29 km/h
(18 MPH)
—
—
OFF
OFF
Approx. 32
km/h (20
MPH) or more
—
Vehicle is ab-
sent
OFF
OFF
OFF
Vehicle is de-
tected
ON
OFF
ON (vehicle
detected di-
rection)
Before turn
signal oper-
ates vehicle is
detected
Blink
Short continuous beeps
Vehicle is de-
tected after
turn signal op-
erates
Blink
OFF
JSOIA0251GB
JSOIA0252GB
JSOIA0251GB
DAS-110
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
>> GO TO 2.
2.
ACTION TEST FOR MOD
1.
Enable the setting of the MOD system on the vehicle information display.
2.
Turn warning systems switch ON (warning systems ON indicator is ON).
3.
Check the MOD operation according to the following table.
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle reaches a
higher speed. Refer to
DAS-22, "MOD : System Description"
.
>> Inspection End.
Vehicle condition/ Driver's operation
Vehicle response
Moving Object De-
tection ON indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Status of vehicle detection
within detection area
Indication on the Moving Object Detection
indicator
Buzzer
OFF
—
—
OFF
OFF
Blue
Less than approx.
8 km/h (5 MPH)
Vehicle is detected
ON
ON
Approx. 8 km/h (5
MPH) or more
Vehicle is absent
ON
OFF
Vehicle is detected
ON
OFF
Vehicle is not detected
ON
OFF
DAS
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
DAS-111
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Description
INFOID:0000000010416835
Vehicle specification needs to be written with CONSULT because it is not written after replacing around view
monitor control unit.
Configuration has three functions as follows:
CAUTION:
• When replacing around view monitor control unit, you must perform “Select Saved Data List” or
"After Replace ECU" with CONSULT.
• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new around view monitor
control unit.
Work Procedure
INFOID:0000000010416836
1.
WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of around view monitor control unit.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “SAVED DATA LIST”
CONSULT
Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select
applicable file from the “Save Data List” and press “Confirm”.
>> Work End.
3.
PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”
CONSULT
1.
Select “After Replace ECU” or “Manual Configuration”.
2.
Identify the correct model and configuration list. Refer to
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
4.
Select “Next”.
CAUTION:
Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated con-
figuration of brand new around view monitor control unit is same as the desirable configuration. If
not, configuration which is set automatically by selecting vehicle model can not be memorized.
5.
When "Completed", select "End".
>> GO TO 4.
4.
OPERATION CHECK
Function
Description
"Before Replace ECU"
• Reads the vehicle configuration of current around view monitor control unit.
• Saves the read vehicle configuration.
"After Replace ECU"
Writes the vehicle configuration with manual selection.
"Select Saved Data List"
Writes the vehicle configuration with saved data.
DAS-112
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Confirm that each function controlled by around view monitor control unit operates normally.
>> Work End.
Configuration List
INFOID:0000000010416837
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
⇔
: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
HANDLE POSITION
RHD
⇔
LHD
—
TRANSMISSION
A/T
⇔
M/T
—
TIRE SIZE
TYPE 1
⇔
TYPE 3
• TYPE 1: 17 inch
• TYPE 3: 19 inch
4WD/2WD
4WD
⇔
2WD
—
SONAR
WITH
⇔
WITHOUT
• WITH 1: With sonar
• WITHOUT: Without sonar
LDW FUNCTION
WITH
⇔
WITHOUT
• WITH 1: With LDW function
• WITHOUT: Without LDW function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст