Nissan Murano Z50 (2004 year). Manual — part 129
GI-54
TERMINOLOGY
Revision: 2004 November
2004 Murano
***: Not applicable
Transmission control module
TCM
A/T control unit
Turbocharger
TC
Turbocharger
Vehicle speed sensor
VSS
Vehicle speed sensor
Volume air flow sensor
VAFS
Air flow meter
Warm up oxidation catalyst
WU-OC
Catalyst
Warm up oxidation catalytic converter sys-
tem
WU-OC system
***
Warm up three way catalyst
WU-TWC
Catalyst
Warm up three way catalytic converter sys-
tem
WU-TWC system
***
Wide open throttle position switch
WOTP switch
Full switch
NEW TERM
NEW ACRONYM /
ABBREVIATION
OLD TERM
GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
GW
A
B
GW
Revision: 2004 November
2004 Murano
GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS . . . . . . . . . . . . . . .. 3
PREPARATION . . . . . . . . . . . . . . ... 4
Special Service Tools . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 5
Work Flow . . . . . . . . . . . . . . . . 5
Generic Squeak and Rattle Troubleshooting . . ... 7
Diagnostic Worksheet . . . . . . . . . . . .. 9
WINDSHIELD GLASS . . . . . . . . . . . ...11
Removal and Installation . . . . . . . . . . .11
REMOVAL . . . . . . . . . . . . . . . 11
INSTALLATION . . . . . . . . . . . . ... 12
BACK DOOR WINDOW GLASS . . . . . . . .. 13
Removal and Installation . . . . . . . . . . 13
REMOVAL . . . . . . . . . . . . . . ... 13
INSTALLATION . . . . . . . . . . . . ... 14
SIDE WINDOW GLASS . . . . . . . . . . . 15
Removal and Installation . . . . . . . . . . 15
REMOVAL . . . . . . . . . . . . . . ... 15
INSTALLATION . . . . . . . . . . . . ... 16
POWER WINDOW SYSTEM . . . . . . . . . 17
Component Parts and Harness Connector Location
GW-2
Revision: 2004 November
2004 Murano
FRONT DOOR GLASS AND REGULATOR . . . . 58
Removal and Installation . . . . . . . . . . 58
REAR DOOR GLASS AND REGULATOR . . . ... 61
Removal and Installation . . . . . . . . . . 61
INSIDE MIRROR . . . . . . . . . . . . . ... 63
Wiring Diagram –I/MIRR– . . . . . . . . . .. 63
Removal and Installation . . . . . . . . . . 64
REMOVAL . . . . . . . . . . . . . . ... 64
INSTALLATION . . . . . . . . . . . . . 64
REAR WINDOW DEFOGGER . . . . . . . . .. 65
DATA MONITOR . . . . . . . . . . . . ..75
ACTIVE TEST . . . . . . . . . . . . . ..75
REPAIR EQUIPMENT . . . . . . . . . . .86
REPAIRING PROCEDURE . . . . . . . . .87
DOOR MIRROR . . . . . . . . . . . . . . .88
WIRING DIAGRAM –MIRROR– . . . . . . .89
Removal and Installation . . . . . . . . . . .90
REMOVAL . . . . . . . . . . . . . . . 90
INSTALLATION . . . . . . . . . . . . . 90
Disassembly and Assembly . . . . . . . . . 90
DISASSEMBLY . . . . . . . . . . . . . 90
ASSEMBLY . . . . . . . . . . . . . . ..91
PRECAUTIONS
GW-3
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AIS001RL
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Handling for Adhesive and Primer
AIS001RM
●
Do not use an adhesive which is past its usable date. Shelf life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Open the seal of the primer and adhesive just before application. Discard the remainder.
●
Before application, be sure to shake the primer container to stir the contents. If any floating material is
found, do not use it.
●
If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with
soap.
●
When using primer and adhesive, always observe the precautions in the instruction manual.
Wiring Diagrams and Trouble Diagnosis
AIS001RN
When you read wiring diagrams, refer to the following:
●
GI-14, "How to Read Wiring Diagrams"
●
PG-3, "POWER SUPPLY ROUTING CIRCUIT"
When you perform trouble diagnosis, refer to the following:
●
GI-10, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES"
●
GI-26, "How to Perform Efficient Diagnosis for an Electrical Incident"
Check for any service bulletins before servicing the vehicle.
GW-4
PREPARATION
Revision: 2004 November
2004 Murano
PREPARATION
PFP:00002
Special Service Tools
AIS001RO
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
AIS001RP
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and
Rattle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
SIIA0995E
SQUEAK AND RATTLE TROUBLE DIAGNOSES
GW-5
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PFP:00000
Work Flow
AIS0038M
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
●
The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
●
If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
●
After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
●
Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces=higher pitch noise/softer surfaces=lower pitch noises/edge to surface=chirping
●
Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.
●
Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
●
Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
●
Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
●
Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
●
Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
●
Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.
●
Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842
GW-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2004 November
2004 Murano
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T models, drive position on A/T models).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
●
Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
●
If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1.
Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear and mechanics stethoscope).
2.
Narrow down the noise to a more specific area and identify the cause of the noise by:
●
removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fastener can be broken
or lost during the repair, resulting in the creation of new noise.
●
tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.
●
feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.
●
placing a piece of paper between components that you suspect are causing the noise.
●
looking for loose components and contact marks.
Refer to
GW-7, "Generic Squeak and Rattle Troubleshooting"
REPAIR THE CAUSE
●
If the cause is a loose component, tighten the component securely.
●
If the cause is insufficient clearance between components:
–
separate components by repositioning or loosening and retightening the component, if possible.
–
insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A Nissan Squeak and Rattle Kit (J-43980) is available through your authorized Nissan Parts
Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the Nissan Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100
×
135 mm (3.94
×
5.31 in)/76884-71L01: 60
×
85 mm (2.36
×
3.35 in)/76884-
71L02: 15
×
25 mm (0.59
×
0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50
×
50 mm (1.97
×
1.97 in)/73982-
50Y00: 10 mm (0.39 in) thick, 50
×
50 mm (1.97
×
1.97 in)
SQUEAK AND RATTLE TROUBLE DIAGNOSES
GW-7
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30
×
50 mm (1.18
×
1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15
×
25 mm (0.59
×
0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle Troubleshooting
AIS0038N
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1.
The cluster lid A and instrument panel
2.
Acrylic lens and combination meter housing
3.
Instrument panel to front pillar garnish
4.
Instrument panel to windshield
5.
Instrument panel mounting pins
6.
Wiring harnesses behind the combination meter
7.
A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1.
Shifter assembly cover to finisher
2.
A/C control unit and cluster lid C
3.
Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1.
Finisher and inner panel making a slapping noise
2.
Inside handle escutcheon to door finisher
3.
Wiring harnesses tapping
4.
Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.
GW-8
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2004 November
2004 Murano
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1.
Trunk lid dumpers out of adjustment
2.
Trunk lid striker out of adjustment
3.
The trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2.
Sunvisor shaft shaking in the holder
3.
Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
SQUEAK AND RATTLE TROUBLE DIAGNOSES
GW-9
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
Diagnostic Worksheet
AIS0038O
PIIB0723E
GW-10
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2004 November
2004 Murano
SBT844
WINDSHIELD GLASS
GW-11
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
WINDSHIELD GLASS
PFP:72712
Removal and Installation
AIS001RT
REMOVAL
1.
Remove the front pillar garnish. Refer to
2.
Partially remove the headlining (front edge). Refer to
.
3.
Remove the front wiper arms. Refer to
WW-31, "Removal and Installation of Front Wiper Arms, Adjust-
ment of Wiper Arms Stop Location"
.
4.
Remove roof side molding. Refer to
5.
Apply a protective tape around the windshield glass to protect the painted surface from damage.
After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag.
●
If a windshield glass is to be reused, mark the body and the glass with mating marks.
PIIA3784E
1.
Clip (C103)
2.
Fastener
3.
Molding
4.
Windshield glass
5.
Spacer
6.
Mirror base
7.
Bond
8.
Insulator
9.
Panel
10. Body side (outer)
11.
Cowl top cover
GW-12
WINDSHIELD GLASS
Revision: 2004 November
2004 Murano
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.
●
The molding must be installed securely so that it is in position and leaves no gap.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the windshield in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks for Windshield
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
PIIA0186E
BACK DOOR WINDOW GLASS
GW-13
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
BACK DOOR WINDOW GLASS
PFP:90300
Removal and Installation
AIS001RV
REMOVAL
1.
Remove the back door finisher. Refer to
2.
Remove the rear wiper arm. Refer to
WW-49, "Removal and Installation of Rear Wiper Arm, Adjustment of
3.
Remove the connectors and grounds for the rear window defogger and printed antenna.
4.
Remove glass using cutting knife or power cutting tool and an inflatable pump bag.
●
If a back door window glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
Be careful not to scratch the glass when removing.
1.
Dam rubber
2.
Back door window glass
3.
Bond
4.
Back door outer panel
PIIA3785E
GW-14
BACK DOOR WINDOW GLASS
Revision: 2004 November
2004 Murano
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the back door window glass in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
PIIB0908E
SIDE WINDOW GLASS
GW-15
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
AIS002H9
REMOVAL
1.
Remove the luggage side finisher upper. Refer to
2.
Remove the headlining. Refer to
.
3.
Apply protective tape around the side window to protect the painted surface from damage.
4.
Remove the side window glass using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIA3793E
1.
Side window glass molding (Upper)
2.
Side window glass
3.
Clip
4.
Side window glass molding (Lower)
5.
Bond
6.
Body side outer panel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст