Nissan Murano Z50 (2004 year). Manual — part 36
BODY REPAIR
BL-169
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
Read the Following Precautions When Repairing HSS:
1.
Additional points to consider
●
The repair of reinforcements (such as side members) by heat-
ing is not recommended since it may weaken the component.
When heating is unavoidable, do not heat HSS parts above
550
°
C (1,022
°
F).
Verify heating temperature with a thermometer.
(Crayon-type and other similar type thermometer are appro-
priate.)
●
When straightening body panels, use caution in pulling any
HSS panel. Because HSS is very strong, pulling may cause
deformation in adjacent portions of the body. In this case,
increase the number of measuring points, and carefully pull
the HSS panel.
●
When cutting HSS panels, avoid gas (torch) cutting if possi-
ble. Instead, use a saw to avoid weakening surrounding areas
due to heat. If gas (torch) cutting is unavoidable, allow a mini-
mum margin of 50 mm (1.97in).
●
When welding HSS panels, use spot welding whenever possi-
ble in order to minimize weakening surrounding areas due to
heat.
If spot welding is impossible, use M.I.G. welding. Do not use
gas (torch) welding because it is inferior in welding strength.
PIIA0115E
PIIA0116E
PIIA0117E
PIIA0144E
BL-170
BODY REPAIR
Revision: 2004 November
2004 Murano
●
The spot weld on HSS panels is harder than that of an ordi-
nary steel panel.
Therefore, when cutting spot welds on a HSS panel, use a
low speed high torque drill (1,000 to 1,200 rpm) to increase
drill bit durability and facilitate the operation.
2.
Precautions in spot welding HSS
This work should be performed under standard working condi-
tions. Always note the following when spot welding HSS:
●
The electrode tip diameter must be sized properly according
to the metal thickness.
●
The panel surfaces must fit flush to each other, leaving no
gaps.
●
Follow the specifications for the proper welding pitch.
Unit: mm
PIIA0145E
PIIA0146E
PIIA0147E
Thickness (t)
Minimum pitch (l)
0.6 (0.024)
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.6 (0.063)
1.8 (0.071)
10 (0.39) or over
12 (0.47) or over
18 (0.71) or over
20 (0.79) or over
27 (1.06) or over
31 (1.22) or over
PIIA0148E
BODY REPAIR
BL-171
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
Replacement Operations
AIS001Y1
DESCRIPTION
This section is prepared for technicians who have attained a high level of skill and experience in repairing col-
lision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
Technicians are also encouraged to read Body Repair Manual (Fundamentals) in order to ensure that the orig-
inal functions and quality of the vehicle can be maintained. The Body Repair Manual (Fundamentals) contains
additional information, including cautions and warning, that are not including in this manual. Technicians
should refer to both manuals to ensure proper repairs.
Please note that these information are prepared for worldwide usage, and as such, certain procedures might
not apply in some regions or countries.
BL-172
BODY REPAIR
Revision: 2004 November
2004 Murano
The symbols used in this section for cutting and welding / brazing operations are shown below.
PIIA0149E
BODY REPAIR
BL-173
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
●
Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is
at position A due to the construction of the vehicle. Refer to the
front pillar section.
●
Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm above inner front pillar cut position.
●
Prepare a cutting jig to make outer pillar easier to cut. Also, this
will permit service part to be accurately cut at joint position.
●
An example of cutting operation using a cutting jig is as follows.
1.
Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2.
Align cutting line with notch on jig. Clamp jig to pillar.
3.
Cut outer pillar along groove of jig. (At position A)
4.
Remove jig and cut remaining portions.
5.
Cut inner pillar at position B in same manner.
PIIA0150E
PIIA0151E
PIIA0152E
PIIA0153E
BL-174
BODY REPAIR
Revision: 2004 November
2004 Murano
HOODLEDGE
Change parts
●
Hoodledge assembly (LH)
●
Hoodledge reinforcement (LH)
SIIA2180E
BODY REPAIR
BL-175
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
HOODLEDGE (PARTIAL REPLACEMENT)
Change parts
●
Upper hoodledge (RH)
●
Lower front hoodledge (RH)
●
Hoodledge reinforcement (RH)
SIIA2181E
BL-176
BODY REPAIR
Revision: 2004 November
2004 Murano
FRONT SIDE MEMBER
●
Work after hoodledge has been removed.
SIIA2182E
BODY REPAIR
BL-177
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
Change parts
●
Front side member (LH)
●
Front side member closing plate assembly (LH)
BL-178
BODY REPAIR
Revision: 2004 November
2004 Murano
FRONT SIDE MEMBER (PARTIAL REPLACEMENT)
Change parts
●
Front side member (RH)
●
Front side member front closing plate (RH)
SIIA2183E
BODY REPAIR
BL-179
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
FRONT PILLAR
●
Work after hoodledge reinforcement has been removed.
SIIA2184E
BL-180
BODY REPAIR
Revision: 2004 November
2004 Murano
Change parts
●
Side body assembly (LH)
●
Inner side roof rail (LH)
●
Side dash (LH)
SIIA2185E
BODY REPAIR
BL-181
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
CENTER PILLAR
Change parts
●
Side body assembly (LH)
●
Inner center pillar (LH)
SIIA2186E
BL-182
BODY REPAIR
Revision: 2004 November
2004 Murano
SIIA2187E
BODY REPAIR
BL-183
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
OUTER SILL
Change parts
SIIA2188E
BL-184
BODY REPAIR
Revision: 2004 November
2004 Murano
●
Outer sill (LH)
●
Outer sill reinforcement assembly (LH)
●
Lower front pillar reinforcement (LH)
●
Rear outer sill reinforcement (LH)
SIIA2189E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст