Murano Cross Cabriolet Z51 (2013 year). Manual — part 34
EXL-62
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000008460320
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000008460321
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to
EXL-39, "Component Function Check"
.
Is the headlamp (LO) circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
Revision: 2012 October
2013 Murano CrossCabriolet
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
EXL-63
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000008460322
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000008460323
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
On
OFF
Off
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-64
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000008460324
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000008460325
1.
CHECK FRONT FOG LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP SHORT CIRCUIT
1.
Disconnect front fog connector and IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 5.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
5.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-50, "Component Function Check"
.
Is the inspection result normal?
YES
>> Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#58
15 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
86
Not existed
LH
87
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
On
OFF
Off
Revision: 2012 October
2013 Murano CrossCabriolet
HEADLAMP AIMING ADJUSTMENT
EXL-65
< PERIODIC MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000008460326
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the front combination lamp assembly has
been replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
• Headlamp aiming switch sets to “0”.
AIMING ADJUSTMENT SCREW
JPLIA0810ZZ
A.
Headlamp RH (UP/DOWN) adjust-
ment screw
B.
Headlamp LH (UP/DOWN) adjust-
ment screw
: Vehicle center
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-66
< PERIODIC MAINTENANCE >
[XENON TYPE]
HEADLAMP AIMING ADJUSTMENT
Aiming Adjustment Procedure
INFOID:0000000008460327
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp bulb center and the
screen.
3.
Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5.
Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp RH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
B
Headlamp LH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Light axis measurement range (R)
: 350
±
175 mm (13.78
±
6.89 in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HEADLAMP AIMING ADJUSTMENT
EXL-67
< PERIODIC MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Distance between the headlamp
center and the screen (L)
: 10 m (32.8 ft)
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-68
< PERIODIC MAINTENANCE >
[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000008460328
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000008460329
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA0811ZZ
JPLIA0008ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-69
< PERIODIC MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-70
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000008460330
REMOVAL
DISASSEMBLY
1.
Front combination lamp
2.
Headlamp extension panel
JPLIA0812ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Resin cap
4.
Seal packing
5.
Xenon bulb socket (Starter)
6.
Xenon bulb
7.
Retaining spring
8.
Seal packing
9.
HID control unit (Inverter)
10.
Parking lamp bulb socket
11. Parking lamp bulb
12. Front turn signal lamp bulb socket
13.
Front turn signal lamp bulb
14. Headlamp housing assembly
JPLIA0813ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT COMBINATION LAMP
EXL-71
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000008460331
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front grille. Refer to
2.
Remove the headlamp extension panel.
3.
Remove the front bumper fascia. Refer to
.
4.
Remove the headlamp mounting bolts.
5.
Remove the harness clips from headlamp housing assembly.
6.
Pull out the headlamp assembly forward the vehicle.
7.
Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000008460332
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Unlock the retaining spring. And then remove the bulb from the
headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the front grille.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
JPLIA0814ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-72
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
Disassembly and Assembly
INFOID:0000000008460333
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Unlock the retaining spring. And then remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the screw. And then disconnect the connector from HID control unit.
6.
Remove the xenon bulb socket from headlamp housing assembly.
7.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
8.
Remove the bulb from parking lamp bulb socket.
9.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from front turn signal lamp bulb socket.
11. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from front side marker lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT FOG LAMP
EXL-73
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000008460334
Removal and Installation
INFOID:0000000008460335
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the front fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp connector.
3.
Remove the screw.
4.
Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000008460336
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove the front fender protector. Keep the service area. Refer to
.
1.
Front fog lamp
: Pawl
JPLIA1592ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-74
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT FOG LAMP
2.
Remove the front fog lamp bulb connector (1).
3.
Rotate the bulb (2) counterclockwise and unlock it.
JPLIA0816ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
OPTICAL SENSOR
EXL-75
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Exploded View
INFOID:0000000008460337
Removal and Installation
INFOID:0000000008460338
REMOVAL
1.
Insert an appropriate tool between the optical sensor and the instrument upper panel. Pull out the optical
sensor upward.
2.
Disconnect the optical sensor connector. And then remove the optical sensor.
INSTALLATION
Install in the reverse order of removal.
1.
Optical sensor
JPLIA0818ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-76
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded View
INFOID:0000000008460339
Removal and Installation
INFOID:0000000008460340
Lighting & turn signal switch is integrated in the combination switch. Refer to
Revision: 2012 October
2013 Murano CrossCabriolet
HAZARD SWITCH
EXL-77
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000008460341
Removal and Installation
INFOID:0000000008460342
REMOVAL
1.
Remove the instrument stay cover (RH). Refer to
.
2.
Remove the screws. And then remove the switch bracket from the instrument stay cover.
3.
Remove the hazard switch.
INSTALLATION
Install in the reverse order of removal.
1.
Hazard switch
2.
Switch bracket
A.
Pawls
JPLIA0819ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст