Murano Cross Cabriolet Z51 (2013 year). Manual — part 37
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-25
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000008463533
Drive Shaft
INFOID:0000000008463534
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Item
Standard
Left side
Right side
Grease quantity
Wheel side
170 – 190 g (6.00 – 6.70 oz)
Transaxle side
155 – 175 g (5.47 – 6.17 oz)
Boots installed length
Wheel side
158.6 mm (6.24 in)
Transaxle side
163.67 mm (6.44 in)
159.47 mm (6.28 in)
Dimension of dynamic damper
—
202 – 208 mm (7.95 – 8.19 in)
Revision: 2012 October
2013 Murano CrossCabriolet
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precautions . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FUEL SYSTEM . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Quick Connector . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
FUEL TANK . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
EVAP CANISTER . . . . . . . . . . . ..
Hydraulic Layout . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Fuel Tank . . . . . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
General Precautions
INFOID:0000000008462072
WARNING:
When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
CAUTION:
• Use gasoline required by the regulations for octane number. Refer to
.
• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
- Release fuel pressure from the fuel lines. Refer to
.
- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Never kink or twist tubes when they are being installed.
• Never tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check
for fuel leakage at connections.
- Start engine and rev it up and check for fuel leakage at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
“MIL” may come on.
• For servicing “On Board Refueling Vapor Recovery (ORVR)” parts, refer to
Revision: 2012 October
2013 Murano CrossCabriolet
PREPARATION
FL-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000008462073
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000008462074
(Kent-Moore No.)
Tool name
Description
(J-46211)
Fuel tank lock ring wrench
Removing and installing fuel tank retainer
SBIA0388E
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
Revision: 2012 October
2013 Murano CrossCabriolet
FL-4
< PERIODIC MAINTENANCE >
FUEL SYSTEM
PERIODIC MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000008462075
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
Quick Connector
INFOID:0000000008462076
CAUTION:
• After connecting fuel tube quick connectors, check quick con-
nectors are secure.
• Ensure that connector and resin tube never contact any adja-
cent parts.
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
1
: Quick connector
2
: Retainer
A
: Hard tube (or the equivalent)
B
: Connection (cross-section)
C
: Resin tube
D
: To under floor fuel line
E
: To fuel tank
F
: Tab
G
: Disconnection
JPBIA0130ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
REMOVAL AND INSTALLATION
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Exploded View
INFOID:0000000008462077
REMOVAL
DISASSEMBLY
1.
Retainer
2.
Sub fuel level sensor unit
3.
Seal packing
4.
Main fuel level sensor unit, fuel filter
and fuel pump assembly
A.
Right side
B.
Left side
: Vehicle front
: Always replace after every disassembly.
JPBIA1694GB
Revision: 2012 October
2013 Murano CrossCabriolet
FL-6
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Removal and Installation
INFOID:0000000008462078
WARNING:
Read “General Precautions” when working on the fuel system. Refer to
REMOVAL
1.
Check fuel level on a level ground. If the fuel level is 7/8 of the fuel tank (full or nearly full), draw appropri-
ate amount of fuel from the fuel tank.
• In the event of malfunction in fuel pump, insert a hose measuring 25 mm (0.98 in) in diameter into the
filler opening to draw approximately 20 liters fuel.
2.
Release the fuel pressure from the fuel lines. Refer to
.
3.
Open fuel filler lid.
4.
Open filler cap and release the pressure inside fuel tank.
5.
Remove rear seat cushion and reclining device assembly. Refer to
6.
Remove inspection hole cover. Refer to
7.
Peel off floor carpet, then remove inspection hole cover units by
turning clips clockwise by 90 degrees.
1.
Sub fuel level sensor unit
2.
Sub fuel level sensor unit base
3.
Fuel filter and fuel pump assembly
4.
Fuel level sensor unit
: Vehicle front
PBIC4901J
Guideline
: Draw approximately 20 liters from a full-tank condition
Left side
: Main fuel level sensor unit, fuel filter
and fuel pump assembly
Right side
: Sub fuel level sensor unit
SBIA0479E
Revision: 2012 October
2013 Murano CrossCabriolet
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
8.
Disconnect harness connector, fuel feed tube and EVAP hose.
Disconnect quick connector as follows:
• Hold the sides of connector, push in tabs (B) and pull out fuel
feed tube.
• If quick connector sticks to tube of main fuel level sensor unit,
push and pull quick connector several times until they start to
move. Then disconnect them by pulling.
CAUTION:
• Quick connector (1) can be disconnected when the tabs
(F) are completely depressed. Never twist it more than
necessary.
• Never use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Never bend or twist resin tube during installation and dis-
connection.
• Never remove the remaining retainer (2) on hard tube (or
the equivalent) (A) except when resin tube or retainer is
replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
PBIC1807E
A
: Pull
JPBIA0134ZZ
B
: Connection (cross-section)
D
: To under floor fuel line
E
: To fuel tank
G
: Disconnection
Retainer color: Green
JPBIA0130ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FL-8
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
9.
Remove retainer for main fuel level sensor unit, fuel filter and
fuel pump assembly and sub fuel level sensor unit with fuel tank
lock ring wrench (SST) by turning counterclockwise.
10. Remove main fuel level sensor unit, fuel filter and fuel pump assembly, and sub fuel level sensor unit.
• Raise main fuel level sensor unit, fuel filter and fuel pump
assembly, and disconnect fuel hose connector (push in tabs
and pull out) and sub fuel level sensor unit harness connector.
• Raise and release sub fuel level sensor unit to remove.
INSTALLATION
Note to the following, and install in the reverse order of removal.
Main and Sub Fuel Level Sensor Unit
1.
Install new seal packing to fuel tank without any twist.
2.
Connect fuel hose connector (push in until it stops) and sub fuel
level sensor unit harness connector.
NOTE:
When installing fuel hose connector insert them fully until a click
sound of full stopper engagement is heard.
JPBIA0135ZZ
SBIA0411E
SBIA0396E
SBIA0398E
Revision: 2012 October
2013 Murano CrossCabriolet
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
3.
Align the direction mark on main fuel level sensor unit, fuel filter
and fuel pump assembly and sub fuel level sensor unit with that
on fuel tank as shown in the figure, and install them to fuel tank.
CAUTION:
• Never allow seal packing to drop.
• Never bend float arm during installing.
4.
Install retainer for main fuel level sensor unit, fuel filter and fuel
pump assembly and sub fuel level sensor unit with fuel tank lock
ring wrench (SST) by turning clockwise.
CAUTION:
Install retainer horizontally.
Quick Connector
Connect quick connector as follows:
1.
Check the connection for damage or any foreign materials.
2.
Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
3.
After connecting, check that the connection is secure by following method.
• Pull (A) the tube and the connector to check they are securely
connected.
• Visually confirm that the two retainer tabs are connected to the
connector.
Disassembly and Assembly
INFOID:0000000008462079
DISASSEMBLY
Fuel level sensor unit, fuel filter and fuel pump assembly side
1.
Disconnect harness connector.
2.
Remove fuel level sensor unit according to the following procedure.
SBIA0397E
SBIA0411E
JPBIA0140ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FL-10
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
a.
Push the pawl of fuel level sensor unit (1) mounting area with an
L-shaped iron rod or an equivalent to unlock.
CAUTION:
Never damage it.
b.
With the fuel level sensor unit unlocked, slide it in the direction
shown by the arrow (
).
Sub fuel level sensor unit assembly side
1.
Remove sub fuel level sensor unit according to the following procedure.
a.
Push the pawl of sub fuel level sensor unit (1) mounting area
with an L-shaped iron rod or an equivalent to unlock.
CAUTION:
Never damage it.
b.
With the sub fuel level sensor unit unlocked, slide it in the direc-
tion shown by the arrow (
).
ASSEMBLY
Install fuel level sensor unit and sub fuel level sensor unit according to the following procedure.
• Insert fuel level sensor unit and sub fuel level sensor unit all the way to the end until a “click” touch and
sound can be recognized.
• Pull fuel level sensor unit and sub fuel level sensor unit in the removal direction to ensure that they do not
become detached.
Inspection
INFOID:0000000008462080
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1.
Turn ignition switch “ON” (with engine stopped), then check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and let it idle and check there are no fuel leakage at the fuel system connections.
PBIC4900J
PBIC4899J
Revision: 2012 October
2013 Murano CrossCabriolet
FUEL TANK
FL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
FUEL TANK
Exploded View
INFOID:0000000008462081
Removal and Installation
INFOID:0000000008462082
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
REMOVAL
• Drain fuel from fuel tank if necessary. Refer to
FL-6, "Removal and Installation"
.
• Perform work on level place.
1.
Perform steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY” on main and sub fuel level sensor units. Refer to
FL-6, "Removal and Installation"
2.
Remove center muffler. Refer to
3.
Remove propeller shaft. Refer to
.
1.
Clamp
2.
EVAP/Vent line hose
3.
Fuel tank
4.
Fuel tank mounting band (RH)
5.
Fuel tank protector
6.
Fuel tank protector (RH)
7.
Fuel tank protector (LH)
8.
Fuel tank mounting band (LH)
9.
Clamp
10. Clamp
11.
Fuel filler hose
12. EVAP (Recirculation) hose
13. Clamp
14.
Fuel filler tube
15. Grommet
16. Fuel filler cap
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA5442GB
Revision: 2012 October
2013 Murano CrossCabriolet
FL-12
< REMOVAL AND INSTALLATION >
FUEL TANK
4.
Remove parking rear brake cables. Refer to
.
5.
Remove rear suspension member assembly. Refer to
.
NOTE:
For this service, drive shaft, final drive, and rear suspension member are required not to be separate one
another during removal.
6.
Remove fuel tank protectors.
7.
Disconnect fuel filler hose (1), EVAP/Vent line hose (3), and
EVAP (Recirculation) hose (2) from the side other than the fuel
tank side.
8.
Support the lower part of fuel tank (1) with transmission jack (A).
CAUTION:
Support the position that fuel tank mounting bands never
engage.
9.
Remove fuel tank mounting bands.
10. Supporting with hands, descend transmission jack carefully, and remove fuel tank.
CAUTION:
• Check that all connection points have been disconnected.
• Confirm there is no interference with vehicle.
11. Remove fuel filler tube if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Surely clamp fuel hoses and insert hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel tube.
• Tighten the clamp hand with the top mark (A) until the mark is on
the bolt head flange.
• To connect quick connector, refer to
FL-6, "Removal and Installation"
.
: Vehicle front
JPBIA1696ZZ
JPBIA0145ZZ
Fuel filler hose
: 35 mm (1.38 in)
The other hoses
: 25 mm (0.98 in)
JPBIA0146ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FUEL TANK
FL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
Inspection
INFOID:0000000008462083
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
• After removing/installing rear suspension assembly, check to adjust wheel alignment and then, adjust neutral
position of steering angle sensor. Refer to
.
Revision: 2012 October
2013 Murano CrossCabriolet
FL-14
< REMOVAL AND INSTALLATION >
EVAP CANISTER
EVAP CANISTER
Hydraulic Layout
INFOID:0000000008462084
EVAPORATIVE EMISSION LINE DRAWING
1.
Intake manifold collector
2.
EVAP canister purge volume control
solenoid valve
3.
EVAP service port
A.
From EVAP canister
: Vehicle front
ALBIA0106ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EVAP CANISTER
FL-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
1.
EVAP control system pressure sen-
sor
2.
EVAP canister vent control valve
3.
EVAP canister
A.
To previous figure
B.
To/From B in this figure
C.
Refer to previous figure
: Vehicle front
JMBIA1122ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст