Murano Cross Cabriolet Z51 (2013 year). Manual — part 38
FL-16
< REMOVAL AND INSTALLATION >
EVAP CANISTER
Exploded View
INFOID:0000000008462085
Removal and Installation
INFOID:0000000008462086
REMOVAL
1.
Lift up the vehicle.
2.
Remove EVAP canister fixing bolt.
3.
Remove EVAP canister.
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
DISASSEMBLY
1.
Turn EVAP canister vent control valve counterclockwise.
2.
Remove the EVAP canister vent control valve.
ASSEMBLY
CAUTION:
Always replace O-ring with a new one.
Assemble in the reverse order of disassembly.
PBIB1383E
PBIB1384E
Revision: 2012 October
2013 Murano CrossCabriolet
EVAP CANISTER
FL-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
Inspection
INFOID:0000000008462087
Check EVAP canister as per the following:
1.
Block port (B).
2.
Blow air into port (A) and check that it flows freely out of port (C).
3.
Release blocked port (B).
4.
Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5.
Block port (A) and (B).
6.
Apply pressure to port (C) and check that there is no leakage.
JMBIA1133ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FL-18
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Tank
INFOID:0000000008462088
Standard and Limit
Fuel tank capacity
Approx. 82 (21-5/8 US gal, 18 Imp gal)
Fuel recommendation
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Precaution for Procedure without Cowl Top Cover
. ..
Precautions for Suspension . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
FRONT COIL SPRING AND STRUT . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
TRANSVERSE LINK . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT STABILIZER . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT SUSPENSION MEMBER . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
Wheelarch Height . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008461643
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000008461644
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000008461645
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Suspension
INFOID:0000000008461646
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
PIIB3706J
Revision: 2012 October
2013 Murano CrossCabriolet
PRECAUTIONS
FSU-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000008461647
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000008461648
Tool number
(Kent-More No.)
Tool name
Description
ST35652000
(
—
)
Strut attachment
Disassembling and assembling strut
ZZA0807D
Tool name
Description
Spring compressor
Removing and installing coil spring
Power tool
Loosening bolts and nuts
S-NT717
PBIC0190E
Revision: 2012 October
2013 Murano CrossCabriolet
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
FSU-5
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000008461649
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
,
,
,
—
—
—
,
,
,
—
NVH in DLN
section
NVH in DLN
section
NVH in
F
AX
and FS
U sections
NVH in
WT section
NVH in
WT section
NVH in F
A
X section
NVH in BR
section
NVH in ST
section
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
tal
la
tio
n
,
loo
s
ene
s
s
S
hoc
k
ab
so
rbe
r d
e
fo
rma
tio
n,
da
ma
ge
o
r de
fle
c
tion
B
u
s
h
in
g
or m
o
u
n
ting
d
e
te
rio
rati
o
n
P
a
rt
s interference
S
p
ri
ng
fat
ig
u
e
S
us
pe
ns
ion
lo
os
en
es
s
In
co
rrec
t wh
ee
l a
lig
nm
en
t
S
ta
b
iliz
er b
a
r f
a
ti
gu
e
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
F
R
ONT
AXLE AND FRONT S
U
SPENSION
TI
RE
ROAD
WHEEL
DRIV
E SHAFT
BR
AK
E
S
T
EERING
Symptom
FRONT SUSPENSION
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-6
< PERIODIC MAINTENANCE >
FRONT SUSPENSION ASSEMBLY
PERIODIC MAINTENANCE
FRONT SUSPENSION ASSEMBLY
Inspection
INFOID:0000000008461650
COMPONENT PART
Check the mounting conditions (looseness, backlash) of each component and component conditions (wear,
damage) are normal.
Ball Joint Axial End Play
1.
Set front wheels in a straight-ahead position.
2.
Move axle side of transverse link in the axial direction by hand.
Check there is no end play.
CAUTION:
• Never depress brake pedal when measuring.
• Never perform with tires on level ground.
• Be careful not to damage ball joint boot. Never damage
the installation position by applying excessive force.
STRUT ASSEMBLY
Check for oil leakage and damage. Replace if necessary.
Axial end play
: Refer to
JSEIA0444ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
WHEEL ALIGNMENT
FSU-7
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
WHEEL ALIGNMENT
Inspection
INFOID:0000000008461651
DESCRIPTION
CAUTION:
• Camber, caster, kingpin inclination angles cannot be adjusted.
• If camber, caster, or kingpin inclination angle is outside the standard, check front suspension parts
for wear and damage. Replace suspect parts if a malfunction is detected.
• Kingpin inclination angle is reference value, no inspection is required.
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
Check the following:
• Tires for improper air pressure and wear. Refer to
• Road wheels for runout.
• Wheel bearing axial end play. Refer to
.
• Transverse link ball joint axial end play. Refer to
• Strut operation.
• Each mounting part of axle and suspension for looseness and deformation.
• Each of suspension member, shock absorber, upper link and transverse link for cracks, deformation and
other damage.
• Vehicle height (posture).
GENERAL INFORMATION AND RECOMMENDATIONS
• A four-wheel thrust alignment should be performed.
- This type of alignment is recommended for any NISSAN/INFINITI vehicle.
- The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel is
centered.
- The alignment rack itself should be capable of accepting any NISSAN/INFINITI vehicle.
- The rack should be checked to ensure that it is level.
• Make sure the machine is properly calibrated.
- Your alignment equipment should be regularly calibrated in order to give correct information.
- Check with the manufacturer of your specific equipment for their recommended Service/Calibration Sched-
ule.
ALIGNMENT PROCESS
IMPORTANT:
Use only the alignment specifications listed in this Service Manual.
• When displaying the alignment settings, many alignment machines use “indicators”: (Green/red, plus or
minus, Go/No Go). Never use these indicators.
- The alignment specifications programmed into your machine that operate these indicators may not be cor-
rect.
- This may result in an ERROR.
• Most camera-type alignment machines are equipped with both “Rolling Compensation” method and optional
“Jacking Compensation” method to “compensate” the alignment targets or head units. “Rolling Compensa-
tion” is the preferred method.
- If using the “Rolling Compensation” method, after installing the alignment targets or head units, push or pull
on the rear wheel to move the vehicle. Do not push or pull on the vehicle body.
- If using the “Jacking Compensation” method, after installing the alignment targets or head units, raise the
vehicle and rotate the wheels 1/2 turn both ways.
NOTE:
Do not use the “Rolling Compensation” method if you are using sensor-type alignment equipment.
- Follow all instructions for the alignment machine you're using for more information.
Adjustment
INFOID:0000000008461652
TOE-IN
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-8
< PERIODIC MAINTENANCE >
WHEEL ALIGNMENT
• Loosen the steering outer socket, and then adjust the length using steering inner socket.
CAUTION:
• Always evenly adjust both toe-in alternately and adjust the difference between the left and right to
the standard.
• Always fix the steering inner socket when tightening the steering outer socket.
• After toe-in adjustment, adjust neutral position of steering angle sensor. Refer to
.
Toe-in
: Refer to
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT COIL SPRING AND STRUT
FSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
REMOVAL AND INSTALLATION
FRONT COIL SPRING AND STRUT
Exploded View
INFOID:0000000008461653
Removal and Installation
INFOID:0000000008461654
REMOVAL
1.
Remove tires with power tool.
2.
Remove lock plate. Refer to
BR-20, "FRONT : Exploded View"
.
3.
Remove wheel sensor. Refer to
BRC-98, "FRONT WHEEL SENSOR : Exploded View"
4.
Remove stabilizer connecting rod from strut assembly. Refer to
.
5.
Remove strut assembly from steering knuckle.
6.
Remove cowl top cover. Refer to
7.
Remove mounting bolts of strut mounting insulator with power tool, and then remove strut assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Become it in projection (A) an illustration to the body outside.
• Perform final tightening of bolts and nuts, under unladen conditions
with tires on level ground.
1.
Piston rod lock nut
2.
Strut mounting insulator
3.
Strut mounting bearing
4.
Coil spring
5.
Bound bumper
6.
Lower rubber seat
7.
Strut
Refer to
JPEIA0136GB
: Vehicle front
JPEIA0094ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-10
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
Disassembly and Assembly
INFOID:0000000008461655
DISASSEMBLY
CAUTION:
Never damage strut assembly piston rod when removing components from strut assembly.
1.
Install strut attachment (A) [SST: ST35652000 (
—
)] to strut
assembly and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly,
wrap a shop cloth around strut to protect from damage.
2.
Using a spring compressor (A) (commercial service tool), com-
press coil spring between strut mounting bearing and lower rub-
ber seat (on strut assembly) until coil spring with a spring
compressor is free.
CAUTION:
Be sure a spring compressor is securely attached to coil
spring. Compress coil spring.
3.
Make sure coil spring with a spring compressor between strut
mounting bearing and lower rubber seat (strut assembly) is free.
And then remove piston rod lock nut while securing the piston
rod tip so that piston rod does not turn.
4.
Remove strut mounting insulator and strut mounting bearing,
and bound bumper from strut.
5.
After removing coil spring with a spring compressor (commercial service tool), then gradually release a
spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6.
Remove lower rubber seat from strut.
7.
Remove the strut attachment [SST: ST35652000 (
—
)] from strut.
ASSEMBLY
1.
Install strut attachment [SST: ST35652000 (
—
)] to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect
from damage.
2.
Install lower rubber seat.
3.
Install bound bumper onto strut mounting insulator.
4.
Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assem-
bly.
CAUTION:
• Face tube side of coil spring (1) downward. Align the
lower end (A) to lower rubber seat (2).
• Be sure a compressor is securely attached to coil spring.
Compress coil spring.
• Set coil spring so that its paint marks are aligned with the
positions of 1.25 turns and 2.25 turns from the bottom end
of the coil spring.
JPEIA0006ZZ
JPEIA0168ZZ
JPEIA0095ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT COIL SPRING AND STRUT
FSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
5.
Install strut mounting bearing and strut mounting insulator with bound bumper to strut.
• Installation position of strut mounting insulator is shown in the
figure.
6.
Secure piston rod tip so that piston rod does not turn, then
tighten piston rod lock nut with specified torque.
CAUTION:
Never reuse piston rod lock nut.
7.
Gradually release a spring compressor (commercial service
tool), and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
8.
Remove the strut attachment [SST: ST35652000 (
—
)] from strut assembly.
Inspection
INFOID:0000000008461656
INSPECTION AFTER DISASSEMBLY
Strut
Check the following items, and replace the parts if necessary.
• Strut for deformation, cracks or damage
• Piston rod for damage, uneven wear or distortion
• Oil leakage
Strut Mounting Insulator and Rubber Parts Inspection
Check strut mounting insulator for cracks and rubber parts for wear. Replace it if necessary.
Coil Spring
Check coil spring for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
.
2.
Check wheel alignment. Refer to
Disposal
INFOID:0000000008461657
1.
Set strut assembly horizontally with the piston rod fully extended.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: Projection
: Vehicle front
JPEIA0094ZZ
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0160ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-12
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000008461658
Removal and Installation
INFOID:0000000008461659
REMOVAL
1.
Remove tires with power tool.
2.
Remove drive shaft of wheel side from wheel hub and bearing assembly. Refer to
.
3.
Remove transverse link from steering knuckle.
4.
Remove transverse link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the front suspension member, under unladen conditions with
tires on level ground.
Inspection
INFOID:0000000008461660
INSPECTION AFTER REMOVAL
Appearance
Check the following items, and replace the part it necessary.
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
1.
Move ball stud at least ten times by hand to check for smooth movement.
1.
Transverse link
2.
Front suspension member
Refer to
for symbols in the figure.
JPEIA0091GB
Revision: 2012 October
2013 Murano CrossCabriolet
TRANSVERSE LINK
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
2.
Hook a spring balance (A) at cutout on ball stud (B). Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
-
If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play Inspection
1.
Move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
-
If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
.
Swing torque
Spring balance
measurement
JPEIA0138ZZ
Axial end play
:Refer to
.
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст