Murano Cross Cabriolet Z51 (2013 year). Manual — part 35
EXL-78
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HEADLAMP AIMING SWITCH
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000008460343
Removal and Installation
INFOID:0000000008460344
REMOVAL
1.
Remove the instrument driver lower panel. Refer to
.
2.
Disengage the pawls. And remove the headlamp aiming switch.
INSTALLATION
Install in the reverse order of removal.
1.
Headlamp aiming switch
A.
Pawls
JPLIA0820ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
REAR COMBINATION LAMP
EXL-79
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000008460345
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000008460346
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Grommet
2.
Rear combination lamp
3.
Rear combination lamp finisher
: Pawl
Refer to
JMLIA2257GB
1.
Rear combination lamp housing
2.
Rear combination lamp harness
3.
Rear side marker lamp bulb
4.
Rear turn signal lamp bulb
JMLIA2280ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-80
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR COMBINATION LAMP
1.
Disengage rear combination lamp finisher fixing pawls as shown
by the arrow in the figure, and then remove the rear combination
lamp finisher.
2.
Remove the rear combination lamp mounting bolts.
3.
Pull the rear combination lamp toward outside of the vehicle, and then remove the rear combination lamp.
4.
Disconnect the rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000008460347
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
REAR SIDE MARKER LAMP BULB
1.
Remove the rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
2.
Rotate the rear side marker lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear side marker lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1.
Remove the rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
2.
Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear turn signal lamp bulb socket.
JMKIA8577ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HIGH-MOUNTED STOP LAMP
EXL-81
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000008460348
Removal and Installation
INFOID:0000000008460349
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove trunk lid trim. Refer to
INT-37, "Removal and Installation"
2.
Disconnect high-mounted stop lamp (1) harness connector (A).
3.
Remove high-mounted stop lamp mounting nuts (B).
4.
Remove high-mounted stop lamp bracket.
5.
Disengage high-mounted stop lamp fixing pawls, and then
remove high-mounted stop lamp.
1.
High-mounted stop lamp bracket
2.
Trunk lid
3.
High-mounted stop lamp
: Pawl
Refer to
JMLIA2259GB
JMLIA2281ZZ
: Pawl
JMLIA2282ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-82
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HIGH-MOUNTED STOP LAMP
INSTALLATION
Install in the reverse order of removal.
Revision: 2012 October
2013 Murano CrossCabriolet
BACK-UP LAMP
EXL-83
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BACK-UP LAMP
Exploded View
INFOID:0000000008460350
Removal and Installation
INFOID:0000000008460351
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the trunk lid trim. Refer to
INT-37, "Removal and Installation"
.
2.
Remove the back-up lamp mounting nuts.
3.
Disconnect the back-up lamp connector, and then remove the back-up lamp.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Replacement
INFOID:0000000008460352
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
1.
Remove the trunk lid trim. Refer to
INT-37, "Removal and Installation"
.
2.
Rotate the back-up lamp bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the back-up lamp bulb socket.
1.
Trunk lid
2.
Seal packing
3.
Back-up lamp housing
4.
Back-up lamp bulb
5.
Back-up lamp bulb socket
Refer to
JMLIA2258GB
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-84
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000008460353
Removal and Installation
INFOID:0000000008460354
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the trunk lid trim. Refer to
INT-37, "Removal and Installation"
.
2.
Remove the trunk lid finisher. Refer to
EXT-44, "Removal and Installation"
3.
Disconnect the license plate lamp connector.
4.
Disengage the license plate lamp fixing pawl, and then remove the license plate lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000008460355
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove the trunk lid finisher. Refer to
INT-37, "Removal and Installation"
2.
Turn the license plate lamp bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the license plate lamp bulb socket.
1.
License plate lamp harness
2.
License plate lamp
: Pawl
JMLIA2260ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-85
< SERVICE DATA AND SPECIFICATIONS (SDS)
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000008460356
Item
Type
Wattage (W)
Front combination lamp
Headlamp (HI/LO)
D2S (Xenon)
35
Front turn signal lamp
WY21W (Amber)
21
Parking lamp
W5W
5
Front side marker lamp
WY5W (Amber)
5
Front fog lamp
H8
35
Rear combination lamp
Stop lamp
LED
—
Tail lamp
LED
—
Rear turn signal lamp
W21W
21
Rear side marker lamp
W5W
5
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Revision: 2012 October
2013 Murano CrossCabriolet
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT WHEEL HUB AND KNUCKLE . . . ..
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT WHEEL HUB AND KNUCKLE . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT BOOT . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Removal and Installation . . . .
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Removal and Installation . ...
Inspection . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
LEFT SIDE . . . . . . . . . . . . . . . . .
LEFT SIDE : Removal and Installation . . . . .
RIGHT SIDE . . . . . . . . . . . . . . . ...
RIGHT SIDE : Removal and Installation . . . . ..
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Disassembly and Assembly
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2012 October
2013 Murano CrossCabriolet
FAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008463512
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000008463513
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Drive Shaft
INFOID:0000000008463514
• Observe the following precautions when disassembling and assembling drive shaft.
• Never disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2012 October
2013 Murano CrossCabriolet
PREPARATION
FAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000008463515
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Tool number
(Kent-More No.)
Tool name
Description
KV40107300
(
—
)
Boot band crimping tool
Installing boot band
KV40107500
(
—
)
Drive shaft attachment
Removing drive shaft
KV38107900
(
—
)
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ST35271000
(J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
• Installing oil seal
• Installing support bearing
ST17130000
(
—
)
Drift
a: 32 mm (1.26 in) dia.
b: 60 mm (2.36 in) dia.
Removing support bearing
ZZA1229D
ZZA1230D
PDIA1183J
ZZA0701D
ZZA0836D
Revision: 2012 October
2013 Murano CrossCabriolet
FAX-4
< PREPARATION >
PREPARATION
Commercial Service Tool
INFOID:0000000008463516
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 October
2013 Murano CrossCabriolet
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
FAX-5
< SYMPTOM DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000008463517
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
—
—
NV
H in
F
A
X
an
d
FSU s
e
c
tio
ns
Re
fe
r to
FRONT AXL
E i
n
t
h
is cha
rt
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
NVH in S
T
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e joi
nt an
gl
e
Jo
in
t sl
id
in
g
re
si
st
a
n
c
e
Im
ba
la
nc
e
Imp
rop
er i
ns
ta
lla
ti
o
n,
lo
os
en
es
s
Part
s interf
erence
Whe
e
l be
ari
n
g
da
ma
ge
FRONT A
X
LE
AND FRONT SUSP
ENSION
FRONT A
XLE
TI
RE
ROAD WHEE
L
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
FRONT
AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2012 October
2013 Murano CrossCabriolet
FAX-6
< PERIODIC MAINTENANCE >
FRONT WHEEL HUB AND KNUCKLE
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000008463518
MOUNTING INSPECTION
Make sure that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT DRIVE SHAFT
FAX-7
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Inspection
INFOID:0000000008463519
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
Revision: 2012 October
2013 Murano CrossCabriolet
FAX-8
< REMOVAL AND INSTALLATION >
FRONT WHEEL HUB AND KNUCKLE
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000008463520
Removal and Installation
INFOID:0000000008463521
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-98, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-20, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 piston type) or
ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 piston type).
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-41, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and
.
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove strut assembly from steering knuckle. Refer to
.
1.
Steering knuckle
2.
Splash guard
3.
Wheel hub and bearing assembly
4.
Wheel hub lock nut
5.
Cotter pin
Refer to
for symbols in the figure.
JPDIF0274GB
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст