Murano Cross Cabriolet Z51 (2013 year). Manual — part 39
FSU-14
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000008461661
Removal and Installation
INFOID:0000000008461662
REMOVAL
1.
Remove tires power tool.
2.
Remove front exhaust tube. Refer to
3.
Remove rear propeller shaft from transfer. Refer to
.
4.
Remove lock plate. Refer to
BR-20, "FRONT : Exploded View"
.
5.
Remove wheel sensor harness from strut assembly. Refer to
.
6.
Disconnect power steering solenoid valve harness connector. Refer to
ST-38, "Removal and Installation"
7.
Remove steering outer socket from steering knuckle. Refer to
.
8.
Remove stabilizer connecting rod.
9.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
10. Remove stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Stabilizer clamp
2.
Stabilizer bushing
3.
Stabilizer bar
4.
Front suspension member
5.
Stabilizer connecting rod
Refer to
for symbols in the figure.
JPEIA0092GB
WEIA0182E
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT STABILIZER
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Install stabilizer clamp that notch (A) becomes vehicle front side
(
).
• Install stabilizer bushing that slit (B) becomes vehicle front side
(
).
Inspection
INFOID:0000000008461663
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
JPEIA0058ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-16
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000008461664
Removal and Installation
INFOID:0000000008461665
REMOVAL
1.
Remove tires with power tool.
2.
Remove air guide mounting nuts (
) and air guide (1).
3.
At first, remove the engine and the transaxle assembly with front
suspension member downward. Then separate the engine, tran-
saxle and drive shaft. Refer to
.
4.
Remove the following parts.
• Steering knuckle and wheel hub and bearing assembly: refer
to
• Steering gear assembly and hydraulic line: refer to
• Stabilizer bar: refer to
• Transverse link: refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-
ber bushing) under unladen condition with tires on level ground.
Inspection
INFOID:0000000008461666
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
.
1.
Front suspension member
2.
Rebound stopper
3.
Front suspension member stay
Refer to
for symbols in the figure.
JPEIA0093GB
JPEIA0097ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000008461667
Measure value under unladen*
2
conditions.
*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000008461668
Wheelarch Height
INFOID:0000000008461669
Item
Standard
Measurement wheel
Left side
Right side
Camber
Degree minute (Decimal degree)
Minimum
–1
°
00
′
(–1.00
°
)
–1
°
15
′
(–1.25
°
)
Nominal
–0
°
15
′
(–0.25
°
)
–0
°
30
′
(–0.50
°
)
Maximum
0
°
30
′
(0.50
°
)
0
°
15
′
(0.25
°
)
Left and right difference*
1
–0
°
18
′
(–0.30
°
) - 0
°
48
′
(0.80
°
)
Caster
Degree minute (Decimal degree)
Minimum
4
°
00
′
(4.00
°
)
4
°
10
′
(4.17
°
)
Nominal
4
°
45
′
(4.75
°
)
4
°
55
′
(4.92
°
)
Maximum
5
°
30
′
(5.50
°
)
5
°
40
′
(5.66
°
)
Left and right difference*
1
–0
°
18
′
(–0.30
°
) - 0
°
48
′
(0.80
°
)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
12
°
00
′
(12.00
°
)
Nominal
12
°
45
′
(12.75
°
)
Maximum
13
°
30
′
(13.50
°
)
Toe-in
Total toe-in
Distance
Minimum
Out 0.5 mm (Out 0.019 in)
Nominal
In 1.5 mm (In 0.059 in)
Maximum
In 3.5 mm (In 0.137 in)
Total toe-angle
Degree minute (Decimal
degree)
Minimum
Out 0
°
02
′
(Out 0.03
°
)
Nominal
In 0
°
06
′
(In 0.1
°
)
Maximum
In 0
°
14
′
(In 0.23
°
)
Item
Standard
Swing torque
Transverse link
0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)
Measurement on spring balance
Transverse link
11.1 – 108.9 N (1.2 – 11.1 kg, 3 – 24 lb)
Axial end play
0 mm (0 in)
Item
Standard
Front (Hr)
843 mm (33.19 in)
Revision: 2012 October
2013 Murano CrossCabriolet
FSU-18
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Rear (Hr)
854 mm (33.62 in)
Item
Standard
SFA746B
Revision: 2012 October
2013 Murano CrossCabriolet
A
B
D
E
F
G
H
I
J
K
L
M
N
P
O
C
QUICK REFERENCE INDEX
A GENERAL INFORMATION
B ENGINE
C ELECTRIC POWER TRAIN
HBC
Hybrid Control System
HBB
Hybrid Battery System
HBR
Hybrid Brake System
EVC
EV Control System
TMS
Traction Motor System
EVB
EV Battery System
VC
Vehicle Charging System
HCO
High Voltage Cooling System
D TRANSMISSION & DRIVELINE
CL
Clutch
E SUSPENSION
SCS
Suspension Control System
F BRAKES
G STEERING
H RESTRAINTS
SBC
Seat Belt Control System
I
VENTILATION, HEATER & AIR
CONDITIONER
Heater & Air Conditioning System
Heater & Air Conditioning Control System
J BODY INTERIOR
K BODY EXTERIOR, DOORS,
ROOF & VEHICLE SECURITY
HD
Hood
L DRIVER CONTROLS
VSP
Approaching Vehicle Sound for Pedestrians (VSP)
M ELECTRICAL & POWER CON-
TROL
Power Supply, Ground & Circuit Elements
N DRIVER INFORMATION &
MULTIMEDIA
Meter, Warning Lamp & Indicator
SN
Sonar System
Audio, Visual & Navigation System
O CRUISE CONTROL &
DRIVER ASSISTANCE
DAS
Driver Assistance System
DMS
Drive Mode System
P MAINTENANCE
All Rights Reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, recording or otherwise,
without the prior written per-
mission of NISSAN MOTOR
CO., LTD.
Edition: October 2012
Publication No. SM3E-1Z51U1
FOREWORD
This manual contains maintenance and repair procedure for the 2013
NISSAN Murano CrossCabriolet.
In order to assure your safety and the efficient functioning of the vehicle,
this manual should be read thoroughly. It is especially important that the
PRECAUTIONS in the GI section be completely understood before starting
any repair task.
All information in this manual is based on the latest product information
at the time of publication. The right is reserved to make changes in specifi-
cations and methods at any time without notice.
IMPORTANT SAFETY NOTICE
The proper performance of service is essential for both the safety of
the technician and the efficient functioning of the vehicle.
The service methods in this Service Manual are described in such a
manner that the service may be performed safely and accurately.
Service varies with the procedures used, the skills of the technician
and the tools and parts available. Accordingly, anyone using service
procedures, tools or parts which are not specifically recommended
by NISSAN must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the service
method selected.
PLEASE HELP MAKE THIS SERVICE MANUAL BETTER!
Your comments are important to NISSAN and will help us to improve our Service Manuals.
Use this form to report any issues or comments you may have regarding our Service Manuals.
Please print this form and type or write your comments below. Mail or fax to:
Nissan North America, Inc.
Technical Service Information
39001 Sunrise Drive, P.O. Box 9200
Farmington Hills, MI USA 48331
FAX: (248) 488-3
88
0
SERVICE MANUAL: Model:
Year:
PUBLICATION NO. (Refer to Quick Reference Index ):
Please describe any Service Manual issues or problems in detail:
Page number(s)
Note: Please include a copy of each page, marked with your comments.
Are the trouble diagnosis procedures logical and easy to use? (circle your answer)
YES
NO
If no, what page number(s)?
Note: Please include a copy of each page, marked with your comments.
Please describe the issue or problem in detail:
Is the organization of the manual clear and easy to follow? (circle your answer)
YES
NO
Please comment:
What information should be included in NISSAN Service Manuals to better support you in servicing or
repairing customer vehicles?
DATE:
YOUR NAME:
POSITION:
DEALER:
DEALER NO.:
ADDRESS:
CITY:
STATE/PROV./COUNTRY:
ZIP/POSTAL CODE:
QUICK REFERENCE CHART MURANO
QUICK REFERENCE CHART MURANO
PFP:00000
ENGINE TUNE-UP DATA (VQ35DE)
ELS0003W
Engine model
VQ35DE
Firing order
1-2-3-4-5-6
Idle speed
CVT (In “P” or “N” position)
rpm
600 ± 50
Ignition timing (BTDC at idle speed)
CVT (In “P” or “N” position)
12
°
± 5
°
Tensions of drive belt
Belt tension is not necessary, as it is automatically adjusted by
drive belt auto-tensioner.
Radiator cap relief pressure
kPa (kg/cm
2
, psi)
Standard
122.3 - 151.7 (1.2 - 1.5, 17.7 - 22.0)
Limit
108 (1.1, 15.6)
Cooling system leakage testing pres-
sure
kPa (kg/cm
2
, psi)
156 (1.59, 22.6)
Compression pressure
kPa (kg/cm
2
, psi)/rpm
Standard
1,275 (13.0, 185)/300
Minimum
981 (10.0, 142)/300
Spark plug
Make
DENSO
Standard type
FXE22HR11
Gap
Standard
1.1 mm (0.043 in)
Limit
1.4 mm (0.055 in)
2013
QUICK REFERENCE CHART MURANO
FRONT WHEEL ALIGNMENT
ELS0003X
FOR USA AND MEXICO MODELS
Measure value under unladen*
2
conditions.
*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
Measure value under unladen*
2
conditions.
*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.
Item
Standard
Measurement wheel
Left side
Right side
Camber
Degree minute (Decimal degree)
Minimum
–1
°
00
′
(–1.00
°
)
–1
°
15
′
(–1.25
°
)
Nominal
–0
°
15
′
(–0.25
°
)
–0
°
30
′
(–0.50
°
)
Maximum
0
°
30
′
(0.50
°
)
0
°
15
′
(0.25
°
)
Left and right difference*
1
–0
°
18
′
(–0
°
30
′
) - 0
°
48
′
(0.80
°
)
Caster
Degree minute (Decimal degree)
Minimum
3
°
55
′
(3.92
°
)
4
°
15
′
(4.25
°
)
Nominal
4
°
40
′
(4.67
°
)
5
°
00
′
(5.00
°
)
Maximum
5
°
25
′
(5.41
°
)
5
°
45
′
(5.75
°
)
Left and right difference*
1
–0
°
18
′
(–0
°
30
′
) - 0
°
48
′
(0.80
°
)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
12
°
00
′
(12.00
°
)
Nominal
12
°
45
′
(12.75
°
)
Maximum
13
°
30
′
(13.50
°
)
Toe-in
Total toe-in
Distance
Minimum
Out 0.5 mm (Out 0.019 in)
Nominal
In 1.5 mm (In 0.059 in)
Maximum
In 3.5 mm (In 0.137 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
Out 0
°
02
′
(Out 0.03
°
)
Nominal
In 0
°
06
′
(In 0.1
°
)
Maximum
In 0
°
14
′
(In 0.23
°
)
Item
Standard
Measurement wheel
Left side
Right side
Camber
Degree minute (Decimal degree)
Minimum
–1
°
00
′
(–1.00
°
)
–1
°
15
′
(–1.25
°
)
Nominal
–0
°
15
′
(–0.25
°
)
–0
°
30
′
(–0.50
°
)
Maximum
0
°
30
′
(0.50
°
)
0
°
15
′
(0.25
°
)
Left and right difference*
1
–0
°
18
′
(–0
°
30
′
) - 0
°
48
′
(0.80
°
)
Caster
Degree minute (Decimal degree)
Minimum
3
°
55
′
(3.92
°
)
4
°
10
′
(4.17
°
)
Nominal
4
°
40
′
(4.67
°
)
4
°
55
′
(4.92
°
)
Maximum
5
°
25
′
(5.41
°
)
5
°
40
′
(5.66
°
)
Left and right difference*
1
–0
°
18
′
(–0.30
°
) - 0
°
48
′
(0.80
°
)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
11
°
55
′
(11.92
°
)
Nominal
12
°
40
′
(12.67
°
)
Maximum
13
°
25
′
(13.41
°
)
Toe-in
Total toe-in
Distance
Minimum
Out 0.5 mm (Out 0.019 in)
Nominal
In 1.5 mm (In 0.059 in)
Maximum
In 3.5 mm (In 0.137 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
Out 0
°
02
′
(Out 0.03
°
)
Nominal
In 0
°
06
′
(In 0.1
°
)
Maximum
In 0
°
14
′
(In 0.23
°
)
2013
QUICK REFERENCE CHART MURANO
REAR WHEEL ALIGNMENT
ELS0003Y
FOR USA AND MEXICO MODELS
Measure value under unladen* conditions.
* : Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
Measure value under unladen* conditions.
* : Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
BRAKE PEDAL
ELS0003Z
Unit: mm (in)
BRAKE BOOSTER
Vacuum type
Unit: mm (in)
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
13
′
(–1.21
°
)
Nominal
–0
°
43
′
(–0.72
°
)
Maximum
–0
°
13
′
(–0.21
°
)
Toe-in
Total toe-in
Distance
Minimum
In 0.9 mm (0.035 in)
Nominal
In 2.7 mm (0.106 in)
Maximum
In 4.5 mm (0.177 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(In 0.07
°
)
Nominal
In 0
°
12
′
(In 0.20
°
)
Maximum
In 0
°
20
′
(In 0.33
°
)
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
11
′
(–1.18
°
)
Nominal
–0
°
41
′
(–0.68
°
)
Maximum
–0
°
11
′
(–0.18
°
)
Toe-in
Total toe-in
Distance
Minimum
In 0.9 mm (0.035 in)
Nominal
In 2.7 mm (0.106 in)
Maximum
In 4.5 mm (0.177 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(In 0.07
°
)
Nominal
In 0
°
12
′
(In 0.20
°
)
Maximum
In 0
°
20
′
(In 0.33
°
)
Item
Standard
Brake pedal height
197.1 - 207.1 (7.76 - 8.15)
Clearance between the stop lamp switch and ASCD brake switch
threaded end
0.20 - 1.96 (0.0079 - 0.0772)
Brake pedal play
3.0 - 11.0 (0.118 - 0.433)
Depressed brake pedal height
[Depressing 490 N (50 kg, 110 lb) while turning the engine ON]
128 (5.04) or more
Item
Standard
Input rod length
127 (5.00)
2013
QUICK REFERENCE CHART MURANO
FRONT DISC BRAKE
Unit: mm (in)
REAR DISC BRAKE
Unit: mm (in)
REFILL CAPACITIES
ELS00040
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
26.0 (1.024)
Thickness variation (measured at 8 positions)
0.008 (0.0003)
Runout (with it attached to the vehicle)
0.040 (0.0016) or less
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.050 (0.0020) or less
UNIT
Liter
US measure
Fuel tank
82
21-5/8 gal
Coolant ( With reservoir tank at “MAX” level )
9.0
9-1/2 qt
Engine
Drain and refill
With oil filter change
4.6
4-7/8 qt
Without oil filter change
4.3
4-1/2 qt
Dry engine (Overhaul)
5.3
5-5/8 qt
Transmission
CVT
10.2
10-3/4 qt
Transfer
0.31
5/8 pt
Final drive
0.55
1-1/8 pt
Power steering system
1.0
1-1/8 qt
Air conditioning system
Compressor oil
0.15
5.07 fl oz
Refrigerant
0.60 kg
1.32 lb
2013
GI-1
GENERAL INFORMATION
C
D
E
F
G
H
I
J
K
L
M
B
GI
SECTION
GI
N
O
P
CONTENTS
GENERAL INFORMATION
HOW TO USE THIS MANUAL . . . . . ..
HOW TO USE THIS MANUAL . . . . . . .
Description . . . . . . . . . . . . . . . ....
Terms . . . . . . . . . . . . . . . . . ....
Units . . . . . . . . . . . . . . . . . . ..
Contents . . . . . . . . . . . . . . . . ....
Relation between Illustrations and Descriptions . ...
Components . . . . . . . . . . . . . . . ..
HOW TO FOLLOW TROUBLE DIAGNOSES . .
Description . . . . . . . . . . . . . . . ....
How to Follow Test Groups in Trouble Diagnosis . ..
Key to Symbols Signifying Measurements or Pro-
cedures . . . . . . . . . . . . . . . . .....
HOW TO READ WIRING DIAGRAMS . . . .
Connector Symbols . . . . . . . . . . . . ...
Sample/Wiring Diagram -Example- . . . . . . .
Connector Information . . . . . . . . . . . .
ABBREVIATIONS . . . . . . . . . . . ..
Abbreviation List . . . . . . . . . . . . . ..
TIGHTENING TORQUE OF STANDARD
BOLTS . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Tightening Torque Table (New Standard Includ-
ed) . . . . . . . . . . . . . . . . . . ...
RECOMMENDED CHEMICAL PRODUCTS
AND SEALANTS . . . . . . . . . . . .
Recommended Chemical Products and Sealants
VEHICLE INFORMATION . . . . . . .
IDENTIFICATION INFORMATION . . . . . .
Model Variation . . . . . . . . . . . . . ...
Information About Identification or Model Code . ..
Dimensions . . . . . . . . . . . . . . . .
Wheels & Tires . . . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Precautions For Xenon Headlamp Service . . . .
Precaution for Procedure without Cowl Top Cover .
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . .
Cautions in Removing Battery Terminal and AV
Control Unit (Models with AV Control Unit) . . . .
General Precautions . . . . . . . . . . . .
Three Way Catalyst . . . . . . . . . . . . .
Multiport Fuel Injection System or Engine Control
System . . . . . . . . . . . . . . . . . .
Hoses . . . . . . . . . . . . . . . . . ..
Engine Oils . . . . . . . . . . . . . . . ..
Air Conditioning . . . . . . . . . . . . . ...
Fuel . . . . . . . . . . . . . . . . . . ..
LIFTING POINT . . . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . ...
Garage Jack and Safety Stand and 2-Pole Lift . ...
Board-On Lift . . . . . . . . . . . . . . ...
TOW TRUCK TOWING . . . . . . . . . .
Tow Truck Towing . . . . . . . . . . . . ...
Vehicle Recovery (Freeing a Stuck Vehicle) . . ...
BASIC INSPECTION . . . . . . . . ...
SERVICE INFORMATION FOR ELECTRICAL
INCIDENT . . . . . . . . . . . . . . ..
Work Flow . . . . . . . . . . . . . . . .
Control Units and Electrical Parts . . . . . . .
How to Check Terminal . . . . . . . . . . ...
Intermittent Incident . . . . . . . . . . . . .
Circuit Inspection . . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
GI-2
CONSULT/GST CHECKING SYSTEM . . . ..
Description . . . . . . . . . . . . . . . ..
CONSULT Function and System Application*1 . ..
CONSULT/GST Data Link Connector (DLC) Cir-
cuit . . . . . . . . . . . . . . . . . . ..
Wiring Diagram - CONSULT/GST CHECKING
SYSTEM - . . . . . . . . . . . . . . . ...
INSPECTION AND ADJUSTMENT . . . . ...
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL . . . . . . . . ..
Revision: 2012 October
2013 Murano CrossCabriolet
HOW TO USE THIS MANUAL
GI-3
< HOW TO USE THIS MANUAL >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
HOW TO USE THIS MANUAL
HOW TO USE THIS MANUAL
Description
INFOID:0000000008461554
This volume explains “Removal, Disassembly, Installation, Inspection and Adjustment” and “Trouble Diag-
noses”.
Terms
INFOID:0000000008461555
• The captions WARNING and CAUTION warn you of steps that must be followed to prevent personal injury
and/or damage to some part of the vehicle.
WARNING indicates the possibility of personal injury if instructions are not followed.
CAUTION indicates the possibility of component damage if instructions are not followed.
BOLD TYPED STATEMENTS except WARNING and CAUTION give you helpful information.
Standard value: Tolerance at inspection and adjustment.
Limit value: The maximum or minimum limit value that should not be exceeded at inspection and adjust-
ment.
Units
INFOID:0000000008461556
• The UNITS given in this manual are primarily expressed as the SI UNIT (International System of Unit), and
alternatively expressed in the metric system and in the yard/pound system.
Also with regard to tightening torque of bolts and nuts, there are descriptions both about range and about the
standard tightening torque.
“Example”
Range
Standard
Contents
INFOID:0000000008461557
• A QUICK REFERENCE INDEX, a black tab (e.g.
) is provided on the first page. You can quickly find the
first page of each section by matching it to the section's black tab.
• THE CONTENTS are listed on the first page of each section.
• THE TITLE is indicated on the upper portion of each page and shows the part or system.
• THE PAGE NUMBER of each section consists of two or three letters which designate the particular section
and a number (e.g. “BR-5”).
• THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks of
work and hidden or tricky steps which are not shown in the previous large illustrations.
Assembly, inspection and adjustment procedures for the complicated units such as the automatic transaxle
or transmission, etc. are presented in a step-by-step format where necessary.
Outer Socket Lock Nut
: 59 - 78 N·m (6.0 - 8.0 kg-m, 43 - 58 ft-lb)
Drive Shaft Installation Bolt
: 44.3 N·m (4.5 kg-m, 33 ft-lb)
Revision: 2012 October
2013 Murano CrossCabriolet
GI-4
< HOW TO USE THIS MANUAL >
HOW TO USE THIS MANUAL
Relation between Illustrations and Descriptions
INFOID:0000000008461558
The following sample explains the relationship between the part description in an illustration, the part name in
the text and the service procedures.
Components
INFOID:0000000008461559
• THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques, lubri-
cation points, section number of the PARTS CATALOG (e.g. SEC. 440) and other information necessary to
perform repairs.
The illustrations should be used in reference to service matters only. When ordering parts, refer to the appro-
priate PARTS CATALOG.
Components shown in an illustration may be identified by a circled number. When this style of illustration is
used, the text description of the components will follow the illustration.
SAIA0519E
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст