Nissan Juke (2012 year). Service Repair Manual — part 211
SRC-86
< DTC/CIRCUIT DIAGNOSIS >
B1089 SEAT BELT PRE-TENSIONER LH
B1089 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000007578303
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578304
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1089
PRE-TEN FRONT LH
[SHORT]
Seat belt pre-tensioner LH circuits are
shorted to each other
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1089 SEAT BELT PRE-TENSIONER LH
SRC-87
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-88
< DTC/CIRCUIT DIAGNOSIS >
B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT
B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007578305
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578306
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1090
B1091
B1092
B1093
B0194
B1095
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT
SRC-89
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007578307
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578308
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1106
B1107
B1108
B1109
B1110
B1111
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-90
< DTC/CIRCUIT DIAGNOSIS >
B1113, B1114 SATELLITE SENSOR RH
B1113, B1114 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000007578309
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578310
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor RH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1113
B1114
SATELLITE SENS RH
[UNIT FAIL]
Satellite sensor RH is malfunctioning
• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1113, B1114 SATELLITE SENSOR RH
SRC-91
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-92
< DTC/CIRCUIT DIAGNOSIS >
B1115 SATELLITE SENSOR RH
B1115 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000007578311
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578312
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor RH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1115
SATELLITE SENS RH
[COMM FAIL]
Satellite sensor RH is malfunctioning or out
of the specified specification
• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1115 SATELLITE SENSOR RH
SRC-93
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-94
< DTC/CIRCUIT DIAGNOSIS >
B1116 SATELLITE SENSOR RH
B1116 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000007578313
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578314
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor RH. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1116
SATELLITE SENS RH
[UNMATCH]
Satellite sensor RH is out of the specified
specification
Diagnosis sensor unit or satellite sensor RH is dif-
ferent from the part specified
Revision: 2011 October
2012 JUKE
B1118, B1119 SATELLITE SENSOR LH
SRC-95
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1118, B1119 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578315
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578316
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor LH. Refer to
SR-24, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1118
B1119
SATELLITE SENS LH
[UNIT FAIL]
Satellite sensor LH is malfunctioning
• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-96
< DTC/CIRCUIT DIAGNOSIS >
B1118, B1119 SATELLITE SENSOR LH
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1120 SATELLITE SENSOR LH
SRC-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1120 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578317
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578318
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor LH. Refer to
SR-24, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1120
SATELLITE SENS LH
[COMM FAIL]
Satellite sensor LH is malfunctioning or out
of the specified specification
• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-98
< DTC/CIRCUIT DIAGNOSIS >
B1120 SATELLITE SENSOR LH
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1121 SATELLITE SENSOR LH
SRC-99
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1121 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007578319
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578320
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor LH. Refer to
SR-24, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1121
SATELLITE SENS LH
[UNMATCH]
Satellite sensor LH is out of the specified
specification
Diagnosis sensor unit or satellite sensor RH is dif-
ferent from the part specified
Revision: 2011 October
2012 JUKE
SRC-100
< DTC/CIRCUIT DIAGNOSIS >
B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT
B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007578321
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-100, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578322
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1122
B1123
B1124
B1125
B1126
B1127
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1129 SIDE AIR BAG MODULE RH
SRC-101
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1129 SIDE AIR BAG MODULE RH
DTC Logic
INFOID:0000000007578323
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status.
SRC-11, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-101, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578324
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE SIDE AIR BAG MODULE
1.
Replace side air bag module RH. Refer to
SE-18, "SEATBACK : Disassembly and Assembly"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1129
SIDE MODULE RH
[OPEN]
Side air bag module RH circuit is open
• Harness or connectors
(The module circuit is open.)
• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст