Nissan Juke (2012 year). Service Repair Manual — part 65
P1813 AWD MODE SWITCH
DLN-45
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD MODE SWITCH CIRCUIT (2)
Check the continuity between AWD mode switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK TERMINALS AND HARNESS CONNECTORS
• Check AWD control module pin terminals for damage or loose connection with harness connector.
• Check AWD mode switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
Component Inspection
INFOID:0000000007580173
1.
CHECK AWD MODE SWITCH
1.
Turn the ignition switch OFF.
2.
Remove AWD mode switch. Refer to
DLN-94, "Removal and Installation"
.
3.
Check the continuity between AWD mode switch harness connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
AWD control module
AWD mode switch
Continuity
Connector
Terminal
Connector
Terminal
B47
9
M48
1
Existed
5
Not existed
6
Not existed
13
1
Not existed
5
Existed
6
Not existed
21
1
Not existed
5
Not existed
6
Existed
AWD mode switch
—
Continuity
Connector
Terminal
M48
3
Ground
Not existed
AWD switch assembly
Condition
Continuity
Terminal
1
3
AWD mode switch: 2WD
Not existed
AWD mode switch: AWD-V or AWD
Existed
5
3
AWD mode switch: 2WD
Existed
AWD mode switch: AWD-V or AWD
Not existed
6
3
AWD mode switch: 2WD or AWD-V
Not existed
AWD mode switch: AWD
Existed
Revision: 2011 October
2012 JUKE
DLN-46
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1813 AWD MODE SWITCH
NO
>> Replace AWD mode switch. Refer to
DLN-94, "Removal and Installation"
Revision: 2011 October
2012 JUKE
P181B INCOMPLETE SELFSHUT
DLN-47
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P181B INCOMPLETE SELFSHUT
DTC Logic
INFOID:0000000007580174
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch OFF, and wait for several seconds.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181B” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580175
1.
CHECK AWD CONTROL MODULE POWER SUPPLY (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control module harness connector.
3.
Check the voltage between AWD control module harness connector and ground.
4.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
5.
Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AWD CONTROL MODULE POWER SUPPLY (2)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#33).
3.
Check the harness for open or short between AWD control module harness connector No.1 terminal and
10A (#33).
Is the inspection result normal?
DTC
Display item
Malfunction detected condition
Possible cause
P181B
INCOMP SELF SHUT
When ignition switch is OFF and AWD
control module power supply is lower or
higher than normal
Self-shut of AWD control module is in-
complete.
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
Revision: 2011 October
2012 JUKE
DLN-48
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181B INCOMPLETE SELFSHUT
YES
>> Perform the trouble diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD CONTROL MODULE GROUND
1.
Turn the ignition switch OFF.
2.
Check the continuity between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181B”
is detected, Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
AWD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
Revision: 2011 October
2012 JUKE
P181D ENGINE TORQUE SIGNAL
DLN-49
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P181D ENGINE TORQUE SIGNAL
DTC Logic
INFOID:0000000007580176
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181D” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580177
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch OFF.
3.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
4.
Stop the vehicle.
5.
Check that malfunction indicator lamp (MIL) turns OFF.
Does malfunction indicator lamp (MIL) turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
EC-70, "DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL)"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181D”
is detected, Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181D
ENGINE SYSTEM
Malfunction is detected in engine torque
signal that is output from ECM through
CAN communication.
• ECM
• AWD control module
• CAN communication line
Revision: 2011 October
2012 JUKE
DLN-50
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181E STEERING ANGLE SENSOR
P181E STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000007580178
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580179
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC “C1143” detected?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181E”
is detected, Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181E
STR ANGLE SEN
Malfunction is detected in steering angle
sensor signal through CAN communica-
tion.
• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor
circuit
• Malfunction of AWD control module
• CAN communication line
Revision: 2011 October
2012 JUKE
P181F INCOMPLETE CALIBRATION
DLN-51
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P181F INCOMPLETE CALIBRATION
DTC Logic
INFOID:0000000007580180
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181F” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580181
1.
PERFORM WRITING UNIT CHARACTERISTICS
1.
Erase self-diagnostic result for “ALL MODE AWD/4WD”.
2.
Perform writing unit characteristics. Refer to
3.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC except “P181F” detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS AGAIN
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
Is DTC “P181F” detected?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Check AWD control module pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181F
INCOMP CALIBRATION
When incomplete writing unit character-
istics of rear final drive is detected.
Writing unit characteristics is incom-
plete.
Revision: 2011 October
2012 JUKE
DLN-52
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1820 ENGINE SPEED SIGNAL
P1820 ENGINE SPEED SIGNAL
DTC Logic
INFOID:0000000007580182
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1820” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580183
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch OFF.
3.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
4.
Stop the vehicle.
5.
Check that malfunction indicator lamp (MIL) turns OFF.
Does malfunction indicator lamp (MIL) turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
EC-70, "DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL)"
.
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1820”
is detected, Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1820
ENGINE SPEED SIG
Malfunction is detected in engine speed
signal that is output from ECM through
CAN communication.
• ECM
• AWD control module
• CAN communication line
Revision: 2011 October
2012 JUKE
P1829 ACCELERATOR PEDAL POSITION SENSOR
DLN-53
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1829 ACCELERATOR PEDAL POSITION SENSOR
DTC Logic
INFOID:0000000007580184
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1829” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580185
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch OFF.
3.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
4.
Stop the vehicle.
5.
Check that malfunction indicator lamp (MIL) turns OFF.
Does malfunction indicator lamp (MIL) turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
EC-70, "DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL)"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1829”
is detected, Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1829
THROTTLE POSI SEN
Malfunction is detected in accelerator
pedal position signal that is output from
ECM through CAN communication.
• ECM
• AWD control module
• CAN communication line
Revision: 2011 October
2012 JUKE
DLN-54
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182D AWD SOLENOID (LEFT)
P182D AWD SOLENOID (LEFT)
DTC Logic
INFOID:0000000007580186
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION (1)
With CONSULT
1.
Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and then wait for 5 seconds or more.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION (2)
With CONSULT
1.
Lift up the vehicle.
2.
Start the engine, and run at idle for 1 second.
3.
Stop the engine.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION (3)
With CONSULT
1.
Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.
2.
Stop the vehicle.
3.
Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.
4.
Stop the vehicle.
5.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580187
1.
CHECK AWD SOLENOID CIRCUIT (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control module harness connector.
3.
Check the resistance between AWD control module harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
P182D
SOLENOID LEFT
Malfunction related to AWD solenoid
(left) has been detected.
• Internal malfunction of electric con-
trolled coupling (left)
• Malfunction of AWD solenoid (left)
power supply circuit (open or short)
• Malfunction of AWD control module
Revision: 2011 October
2012 JUKE
P182D AWD SOLENOID (LEFT)
DLN-55
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK AWD SOLENOID CIRCUIT (2)
1.
Disconnect rear final drive assembly harness connector.
2.
Check the continuity between AWD control module harness connector and rear final drive assembly har-
ness connector.
3.
Check the continuity between AWD control module harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD SOLENOID
Check AWD solenoid. Refer to
DLN-55, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to
145, "Removal and Installation"
4.
CHECK TERMINALS AND HARNESS CONNECTORS
1.
Check AWD control module pin terminals for damage or loose connection with harness connector.
2.
Check rear final drive assembly pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
Component Inspection
INFOID:0000000007580188
1.
CHECK AWD SOLENOID
1.
Turn the ignition switch OFF.
2.
Disconnect rear final drive assembly harness connector.
3.
Check the resistance between rear final drive assembly connector terminals.
AWD control module
Condition
Resistance (Approx.)
Connector
Terminal
B47
23
24
10
°
C (50
°
F)
2.55
Ω
20
°
C (68
°
F)
2.65
Ω
30
°
C (86
°
F)
2.76
Ω
AWD control module
Rear final drive assembly
Continuity
Connector
Terminal
Connector
Terminal
B47
23
B64
4
Existed
24
8
AWD control module
—
Continuity
Connector
Terminal
B47
23
Ground
Not existed
24
Revision: 2011 October
2012 JUKE
DLN-56
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182D AWD SOLENOID (LEFT)
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to
145, "Removal and Installation"
.
Rear final drive assembly
Condition
Resistance (Approx.)
Terminal
4
8
10
°
C (50
°
F)
2.55
Ω
20
°
C (68
°
F)
2.65
Ω
30
°
C (86
°
F)
2.76
Ω
Revision: 2011 October
2012 JUKE
P182E AWD SOLENOID (RIGHT)
DLN-57
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P182E AWD SOLENOID (RIGHT)
DTC Logic
INFOID:0000000007580189
DTC DETECTION LOGIC
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION (1)
With CONSULT
1.
Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and then wait for 5 seconds or more.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION (2)
With CONSULT
1.
Lift up the vehicle.
2.
Start the engine, and run at idle for 1 second.
3.
Stop the engine.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION (3)
With CONSULT
1.
Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.
2.
Stop the vehicle.
3.
Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.
4.
Stop the vehicle.
5.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580190
1.
CHECK AWD SOLENOID CIRCUIT (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control module harness connector.
3.
Check the resistance between AWD control module harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
P182E
SOLENOID RIGHT
Malfunction related to AWD solenoid
(right) has been detected.
• Internal malfunction of electric con-
trolled coupling (right)
• Malfunction of AWD solenoid (right)
power supply circuit (open or short)
• Malfunction of AWD control module
Revision: 2011 October
2012 JUKE
DLN-58
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182E AWD SOLENOID (RIGHT)
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK AWD SOLENOID CIRCUIT (2)
1.
Disconnect rear final drive assembly harness connector.
2.
Check the continuity between AWD control module harness connector and rear final drive assembly har-
ness connector.
3.
Check the continuity between AWD control module harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD SOLENOID
Check AWD solenoid. Refer to
DLN-58, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to
145, "Removal and Installation"
.
4.
CHECK TERMINALS AND HARNESS CONNECTORS
1.
Check AWD control module pin terminals for damage or loose connection with harness connector.
2.
Check rear final drive assembly pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
Component Inspection
INFOID:0000000007580191
1.
CHECK AWD SOLENOID
1.
Turn the ignition switch OFF.
2.
Disconnect rear final drive assembly harness connector.
3.
Check the resistance between rear final drive assembly connector terminals.
AWD control module
Condition
Resistance (Approx.)
Connector
Terminal
B47
25
26
10
°
C (50
°
F)
2.55
Ω
20
°
C (68
°
F)
2.65
Ω
30
°
C (86
°
F)
2.76
Ω
AWD control module
Rear final drive assembly
Continuity
Connector
Terminal
Connector
Terminal
B47
25
B64
2
Existed
26
6
AWD control module
—
Continuity
Connector
Terminal
B47
25
Ground
Not existed
26
Revision: 2011 October
2012 JUKE
P182E AWD SOLENOID (RIGHT)
DLN-59
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to
145, "Removal and Installation"
Rear final drive assembly
Condition
Resistance (Approx.)
Terminal
2
6
10
°
C (50
°
F)
2.55
Ω
20
°
C (68
°
F)
2.65
Ω
30
°
C (86
°
F)
2.75
Ω
Revision: 2011 October
2012 JUKE
DLN-60
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182F COUPLING TEMPERATURE SENSOR (LEFT)
P182F COUPLING TEMPERATURE SENSOR (LEFT)
DTC Logic
INFOID:0000000007580192
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182F” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580193
1.
CHECK ELECTRIC CONTROLLED COUPLING (LEFT) TEMPERATURE SENSOR POWER SUPPLY
1.
Turn the ignition switch OFF.
2.
Disconnect rear final drive assembly harness connector.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
4.
Check the voltage between rear final drive assembly harness connector terminals.
Is the inspection result normal?
DTC
Display item
Malfunction detected condition
Possible cause
P182F
TEMP SENSOR LEFT
When electric controlled coupling (left)
temperature is lower than normal
• Electric controlled coupling (left) tem-
perature sensor
- Internal malfunction of electric con-
trolled coupling (left) temperature sen-
sor
- Malfunction of electric controlled cou-
pling (left) temperature sensor circuit
(open)
• Malfunction of AWD control module
When electric controlled coupling (left)
temperature is higher than normal
• Electric controlled coupling (left) tem-
perature sensor
- Internal malfunction of electric con-
trolled coupling (left) temperature sen-
sor
- Malfunction of electric controlled cou-
pling (left) temperature sensor circuit
(short)
• Malfunction of AWD control module
+
−
Voltage
Rear final drive assembly
Connector
Terminal
B64
3
7
Approx. 5 V
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст