Nissan Juke (2012 year). Service Repair Manual — part 199
B210E STARTER RELAY
SEC-101
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DTC confirmation procedure 2>>GO TO 5.
2.
CHECK STARTER RELAY OUTPUT SIGNAL
1.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Disconnect IPDM E/R connector.
4.
Check continuity between BCM harness connector and IPDM E/R harness connector.
5.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK STARTER RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Check harness for open or short between IPDM E/R and battery. Refer to
(M/T models), or
STR-10, "CVT : Wiring Diagram"
(CVT models).
5.
CHECK IGNITION POWER SUPLLY NO.2 SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
97
Ground
Selector lever
(CVT models)
P or N position
12
Other than above
0
Clutch pedal
(M/T models)
Depressed
12
Not depressed
0
BCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M70
97
E13
30
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
97
Not existed
(+)
(–)
Voltage (V)
IPDM E/R
Connector
Terminal
E10
4
Ground
9 - 16
Revision: 2011 October
2012 JUKE
SEC-102
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> GO TO 6.
6.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between IPDM E/R harness connector and BCM harness connector.
3.
Check continuity between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform DTC CONFIRMATION PROCEDURE for DTC B210E. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
(+)
(–)
Condition
Voltage (V)
IPDM E/R
Connector
Terminal
E17
69
Ground
Power supply position
OFF
0 - 1
ON
6 - 16
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E17
69
M70
101
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E17
69
Not existed
Revision: 2011 October
2012 JUKE
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-103
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000007579749
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-103, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579750
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect transmission range switch connector.
4.
Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
There is a difference between P/N position
signal from transmission range switch and
P/N position signal from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
E15
48
F27
2
Existed
Revision: 2011 October
2012 JUKE
SEC-104
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
E15
48
Ground
Not existed
Revision: 2011 October
2012 JUKE
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-105
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000007579751
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-105, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579752
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect transmission range switch connector.
4.
Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2110
INTRLCK/PNP SW OFF
There is a difference between P/N position
signal from transmission range switch and
P/N position signal from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
E15
48
F27 2
Existed
Revision: 2011 October
2012 JUKE
SEC-106
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
E15
48
Ground
Not existed
Revision: 2011 October
2012 JUKE
HEADLAMP FUNCTION
SEC-107
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HEADLAMP FUNCTION
Component Function Check
INFOID:0000000007579753
1.
CHECK FUNCTION
1.
Perform “HEAD LAMP(HI)” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
2.
Check headlamps operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
SEC-107, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000007579754
1.
CHECK HEADLAMP FUNCTION
EXL-41, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
.
>> INSPECTION END
Test item
Description
HEAD LAMP (HI)
ON
Headlamps (Hi)
Light
OFF
Do not light
Revision: 2011 October
2012 JUKE
SEC-108
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Component Function Check
INFOID:0000000007579755
1.
CHECK FUNCTION
1.
Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT.
2.
Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-108, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000007579756
1.
CHECK HORN FUNCTION
Check that horn functions properly using horn switch.
Do horns sound?
YES
>> GO TO 2.
NO
>> Check horn circuit. Refer to
2.
CHECK HORN CONTROL CIRCUIT
1.
Disconnect horn relay.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and horn relay harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
>> INSPECTION END
Test item
Description
VEHICLE SECURITY HORN
ON
Horn
Sounds (for 0.5 sec)
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E13
34
E5
1
Existed
Revision: 2011 October
2012 JUKE
SECURITY INDICATOR LAMP
SEC-109
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000007579757
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-109, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000007579758
1.
CHECK FUSE
1.
Turn power switch OFF.
2.
Check that the following fuse in the fuse block (J/B) is not blown.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the cause of blowing.
2.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Disconnect combination meter connector.
2.
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect combination meter connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
REPLACE BCM
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminates
OFF
Does not illuminate
Signal name
Fuse No.
Battery power supply
11 (10 A)
(+)
(–)
Voltage (V)
(Approx.)
Combination meter
Connector
Terminal
M34
27
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M68
23
Ground
Battery voltage
Revision: 2011 October
2012 JUKE
SEC-110
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
5.
CHECK SECURITY INDICATOR LAMP CIRCUIT
1.
Disconnect combination meter connector.
2.
Check continuity between combination meter harness connector and BCM harness connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
NO
>> Repair or replace harness.
Combination meter
BCM
Continuity
Connector
Terminal
Connector
Terminal
M34
18
M68
23
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
18
Not existed
Revision: 2011 October
2012 JUKE
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE
SEC-111
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
Description
INFOID:0000000007579759
Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.
NOTE:
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regarding control. The vehicle security function can oper-
ate only when the door lock and power distribution systems are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY”: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
• One or more of Intelligent Keys with registered Intelligent Key ID are in the vehicle.
Diagnosis Procedure
INFOID:0000000007579760
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of BCM using CON-
SULT.
Refer to
DLK-30, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-93, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
SEC-112
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000007579761
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Power supply position is not the ON position.
Diagnosis Procedure
INFOID:0000000007579762
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-109, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-113
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000007579763
Armed phase is not activated when all doors are locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000007579764
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000007579765
Armed phase is not activated when all doors are locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000007579766
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to
DLK-16, "DOOR LOCK FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
SWITCHES : Diagnosis Procedure"
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
Revision: 2011 October
2012 JUKE
SEC-114
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000007579767
ARMED phase is not activated when all doors are locked using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000007579768
1.
CHECK POWER DOOR LOCK SYSTEM
Lock or unlock doors using mechanical key.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000007579769
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000007579770
1.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
SEC-115
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000007579771
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000007579772
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-71, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the malfunctioning door switch
2.
CHECK HEADLAMPS FUNCTION
Check head lamps function.
Refer to
SEC-107, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-108, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
SEC-116
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
NATS ANTENNA AMP.
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000007579773
REMOVAL
1.
Remove the cluster lid A. Refer to
IP-12, "Removal and Installation"
.
2.
Remove the NATS antenna amp.
1.
Disengage the NATS antenna amp. (1) fixing pawls using
remover tool.
2.
Pull NATS antenna amp. to remove it from push-button igni-
tion switch (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6573ZZ
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст