Nissan Juke (2012 year). Service Repair Manual — part 122
HEADLAMP
EXL-81
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
HEADLAMP
Exploded View
INFOID:0000000007579225
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000007579226
CAUTION:
Disconnect the battery negative terminal or the fuse.
REMOVAL
1.
Headlamp assembly
: N·m (kg-m, in-lb)
JMLIA1768GB
1.
Headlamp housing assembly
2.
Cap
3.
Halogen bulb
4.
Bulb holder
JMLIA1317ZZ
Revision: 2011 October
2012 JUKE
EXL-82
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HEADLAMP
1.
Remove front bumper fascia. Refer to
EXT-12, "Removal and Installation"
.
2.
Remove headlamp mounting bolts.
3.
Pull out the headlamp assembly forward the vehicle, and then disconnect the connector before removing
the headlamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000007579227
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Disconnect headlamp bulb connector.
2.
Remove bulb holder.
3.
Remove halogen bulb from the headlamp housing assembly.
Disassembly and Assembly
INFOID:0000000007579228
DISASSEMBLY
1.
Remove back cover.
2.
Remove bulb holder.
3.
Remove halogen bulb from the headlamp housing assembly.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2011 October
2012 JUKE
FRONT COMBINATION LAMP
EXL-83
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000007579229
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000007579230
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Front combination lamp
: N·m (kg-m, in-lb)
JMLIA1236ZZ
1.
Parking lamp bulb
2.
Parking lamp bulb socket
3.
Front marker lamp bulb socket
4.
Front marker lamp bulb
5.
Front turn signal lamp bulb socket
6.
Front turn signal lamp bulb
7.
Front combination lamp housing
JMLIA1318ZZ
Revision: 2011 October
2012 JUKE
EXL-84
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
1.
Remove front bumper fascia. Refer to
EXT-12, "Removal and Installation"
.
2.
Remove front combination lamp mounting bolts and nut.
3.
Pull out front combination lamp assembly forward the vehicle, and then disconnect the connector before
removing the headlamp assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
Interference of front combination lamp lens with front fender may cause intrusion of water into front
combination lamp or rusting of fender due to damage of painted surface. Be careful to operate without
allowing parts to interfere with each other.
Replacement
INFOID:0000000007579231
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
PARKING LAMP BULB
1.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
2.
Remove parking lamp bulb from the bulb socket.
FRONT MARKER LAMP BULB
1.
Rotate the front marker lamp bulb socket counterclockwise and unlock it.
2.
Remove the front marker lamp bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000007579232
DISASSEMBLY
1.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
2.
Remove parking lamp bulb from the bulb socket.
3.
Rotate the front marker lamp bulb socket counterclockwise and unlock it.
4.
Remove the front marker lamp bulb from the bulb socket.
5.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6.
Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item and then, install in the reverse order of removal.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2011 October
2012 JUKE
FRONT FOG LAMP
EXL-85
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000007579233
Removal and Installation
INFOID:0000000007579234
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove fender protector. Keep the service area. Refer to
EXT-21, "Removal and Installation"
.
2.
Disconnect front fog lamp harness connector.
3.
Remove front fog lamp bracket.
4.
Remove front fog lamp mounting bolt, and then remove front fog lamp from front fog lamp bracket.
INSTALLATION
Note the following item, and then installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000007579235
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove fender protector. Keep the service area. Refer to
EXT-21, "Removal and Installation"
.
1.
Front fog lamp assembly
2.
Metal clip
3.
Front fog lamp bulb
4.
Front fog lamp bracket
5.
U nut
6.
Front bumper fascia lower
: N·m (kg-m, in-lb)
JMLIA1240GB
Revision: 2011 October
2012 JUKE
EXL-86
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
FRONT FOG LAMP
2.
Remove front fog lamp bulb connector (1).
3.
Rotate the bulb (2) counterclockwise and unlock it.
JPLIA0345ZZ
Revision: 2011 October
2012 JUKE
OPTICAL SENSOR
EXL-87
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Exploded View
INFOID:0000000007579236
Removal and Installation
INFOID:0000000007579237
REMOVAL
1.
Insert an appropriate tool between the switch panel and the instrument upper panel. Pull out the optical
sensor upward.
2.
Disconnect the optical sensor connector.
3.
Remove optical sensor from switch panel.
INSTALLATION
Install in the reverse order of removal.
1.
Optical sensor
2.
Switch panel
: Pawl
JMLIA1245ZZ
Revision: 2011 October
2012 JUKE
EXL-88
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000007579238
REMOVAL
Remove light & turn signal switch. Refer to
BCS-81, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
Revision: 2011 October
2012 JUKE
HAZARD SWITCH
EXL-89
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000007579239
Removal and Installation
INFOID:0000000007579240
REMOVAL
1.
Remove audio unit. Refer to
AV-59, "Removal and Installation"
2.
Disengage fixing pawls, and then remove hazard switch from instrument panel inside to outside.
INSTALLATION
Install in the reverse order of removal.
1.
Instrument panel assembly
2.
Hazard switch
: Pawl
JMLIA1246ZZ
Revision: 2011 October
2012 JUKE
EXL-90
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded View
INFOID:0000000007579241
Removal and Installation
INFOID:0000000007579242
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the side turn signal lamp in numerical order shown in
the figure.
2.
Rotate the bulb socket counterclockwise and unlock it.
NOTE:
Support side turn signal lamp harness with tape so that it won't fall
into the front fender.
INSTALLATION
1.
Rotate the bulb socket clockwise and lock it.
2.
Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side.
Replacement
INFOID:0000000007579243
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1.
Remove side turn signal lamp. Refer to
EXL-90, "Removal and Installation"
2.
Remove bulb from the bulb socket.
1.
Side turn signal lamp bulb
2.
Side turn signal lamp housing
JMLIA1241ZZ
: Vehicle front (side turn signal lamp LH)
: Vehicle rear (side turn signal lamp RH)
JMLIA1302ZZ
Revision: 2011 October
2012 JUKE
HEADLAMP AIMING SWITCH
EXL-91
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000007579244
Removal and Installation
INFOID:0000000007579245
REMOVAL
1.
Remove instrment lower panel assembly LH. Refer to
IP-12, "Removal and Installation"
2.
Remove headlamp aiming switch fixing clips, and then remove headlamp aiming switch from instrument
lower panel assembly LH.
INSTALLATION
Install in the reverse order of removal.
1.
Headlamp aiming switch
2.
Instrument lower panel assembly LH
: Pawl
JMLIA1442ZZ
Revision: 2011 October
2012 JUKE
EXL-92
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000007579246
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000007579247
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Full open back door.
1.
Grommet
2.
Grommet
3.
Rear combination lamp
: Clip
: N·m (kg-m, in-lb)
JMLIA1217GB
1.
Rear combination lamp housing assembly 2.
Back-up lamp bulb
3.
Harness connector
4.
Rear turn signal/tail lamp bulb
5.
Stop lamp bulb
JMLIA1218ZZ
Revision: 2011 October
2012 JUKE
REAR COMBINATION LAMP
EXL-93
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Remove luggage side lower finisher. Refer to
INT-34, "LUGGAGE SIDE LOWER FINISHER : Removal
3.
Remove rear combination lamp mounting bolts.
4.
Insert a remover tool into the rear combination lamp rear fender to disengage the clips.
5.
Pull up rear combination lamp, and then remove rear combination lamp.
6.
Disconnect rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000007579248
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL/TAIL LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-92, "Removal and Installation"
.
2.
Rotate rear turn signal/tail lamp bulb socket counterclockwise, and then remove rear turn signal/tail lamp
bulb socket.
3.
Remove rear turn signal/tail lamp bulb from rear turn signal/tail lamp bulb socket.
STOP LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-92, "Removal and Installation"
.
2.
Rotate stop lamp bulb socket counterclockwise, and then remove stop lamp bulb socket.
3.
Remove stop lamp bulb from stop lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-92, "Removal and Installation"
.
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
Revision: 2011 October
2012 JUKE
EXL-94
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000007579249
Removal and Installation
INFOID:0000000007579250
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove blind seal from back door inside.
CAUTION:
Be careful not to damage the blind seal, so that it can be reused.
2.
Remove high-mounted stop lamp mounting nuts and connector.
3.
Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.
INSTALLATION
Note the following item and then, install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
1.
High-mounted stop lamp
2.
Seal packing
: N·m (kg-m, in-lb)
JMLIA1220GB
Revision: 2011 October
2012 JUKE
LICENSE PLATE LAMP
EXL-95
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP
Exploded View
INFOID:0000000007579251
Removal and Installation
INFOID:0000000007579252
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
While pressing the license plate lamp to direction right side, pull
it to direction outside and then remove it.
2.
Disconnect license plate lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000007579253
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove license plate lamp.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the socket.
1.
License plate lamp housing assembly
2.
Bulb
3.
License plate lamp bulb socket
: Pawl
JMLIA1219ZZ
JPLIA0364ZZ
Revision: 2011 October
2012 JUKE
EXL-96
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HALOGEN TYPE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000007579254
Item
Type
Wattage (W)
Headlamp (HI/LO)
HB5
65/55
Front combination lamp
Front turn signal lamp
PY21W (Amber)
21
Parking lamp
WY5W (Amber)
5
Front marker lamp
12V3.8W
3.8
Front fog lamp
H8
35
Side turn signal lamp
WY5W (Amber)
5
Rear combination lamp
Rear turn signal lamp/Tail lamp
W21/5W
21/5
Stop lamp
W21W
21
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст