Nissan Juke (2012 year). Service Repair Manual — part 71
FRONT OIL SEAL
DLN-141
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3.
Align the matching mark (A) of drive pinion with the matching
mark (B) of companion flange (1), and then install the compan-
ion flange.
4.
Temporarily tighten drive pinion lock nut to drive pinion, using
the flange wrench (Commercial service tool).
CAUTION:
• Never reuse drive pinion lock nut.
• Apply anti-corrosion oil to the thread and seat of new
drive pinion lock nut.
5.
Tighten drive pinion lock nut within the limits of specified torque
so as to keep the pinion bearing preload within a standard val-
ues, using the preload gauge (A) [SST: ST3127S000 (J-25765-
A)].
CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tight-
ening torque first.
• If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion lock nut to adjust the preload torque.
6.
Check for companion flange runout as follows:
• For companion flange face, fit a dial indicator (1) onto the com-
panion flange face (inner side of the propeller shaft mounting
bolt holes). For inner side of the companion flange, fit a test
indicator (2) to the inner side of companion flange (socket
diameter).
• Rotate companion flange to check for runout.
• If the runout value is outside the runout limit, follow the proce-
dure below to adjust.
- Check for runout while changing the phase between companion flange and drive pinion by 90
°
step, and
search for the position where the runout is the minimum.
- If the runout value is still outside of the limit after the phase has been changed, replace companion
flange.
- If the runout value is still outside of the limit after companion flange has been replaced, possible cause
will be an assembly malfunction of drive pinion.
7.
Make a stamping for identification of front oil seal replacement frequency. Refer to “Identification stamp of
replacement frequency of front oil seal”.
CAUTION:
Make a stamping after replacing front oil seal.
8.
Install electric controlled couplings. Refer to
DLN-145, "Removal and Installation"
.
JSDIA2118ZZ
Total preload torque
: A value that add 0.1 – 0.4
N·m (0.01 – 0.04 kg-m, 1.0 –
3.0 in-lb) to the measured
value before removing.
JSDIA2123ZZ
Companion flange runout
: Refer to
.
JSDIA2539ZZ
Revision: 2011 October
2012 JUKE
DLN-142
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
FRONT OIL SEAL
9.
Install rear drive shaft. Refer to
RAX-17, "Removal and Installation"
.
10. Install propeller shaft. Refer to
DLN-125, "Removal and Installation"
11. Refill gear oil to the final drive and check level. Refer to
12. Check the final drive for oil leakage. Refer to
Revision: 2011 October
2012 JUKE
SIDE OIL SEAL
DLN-143
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
Exploded View
INFOID:0000000007580294
Removal and Installation
INFOID:0000000007580295
REMOVAL
1.
Drain gear oil. Refer to
.
2.
Remove electric controlled couplings. Refer to
DLN-145, "Removal and Installation"
3.
Remove side oil seal with the suitable oil seal remover.
CAUTION:
Never damage gear carrier and rear cover.
INSTALLATION
1.
Electric controlled coupling (right)
2.
Side oil seal (right)
3.
Rear final drive assembly
4.
Side oil seal (left)
5.
Electric controlled coupling (left)
A.
Oil seal lip
: Always replace after every disassembly.
: Apply multi purpose grease
: Apply gear oil.
JSDIA2233GB
JSDIA2234ZZ
Revision: 2011 October
2012 JUKE
DLN-144
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
SIDE OIL SEAL
1.
Install side oil seal (right) until it becomes flush with the gear car-
rier end, using the drift (A) [SST: ST33400001 (J-26082)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lip, and gear oil
onto the circumference of oil seal.
2.
Install side oil seal (left) until it becomes flush with the gear car-
rier end, using the drift (A) [SST: KV38100500 (
—
)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lip, and gear oil
onto the circumference of oil seal.
3.
Install electric controlled couplings. Refer to
4.
Refill gear oil to the final drive and check level. Refer to
5.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
JSDIA2235ZZ
JSDIA2236ZZ
Revision: 2011 October
2012 JUKE
ELECTRIC CONTROLLED COUPLING
DLN-145
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ELECTRIC CONTROLLED COUPLING
Exploded View
INFOID:0000000007580296
Removal and Installation
INFOID:0000000007580297
REMOVAL
1.
Remove rear drive shaft. Refer to
RAX-17, "Removal and Installation"
2.
Disconnect sub-harness connector (1).
3.
Remove propeller shaft assembly. Refer to
4.
Support rear final drive assembly with a suitable jack.
5.
Remove rear final drive mounting bolt (
) at rear suspension
member.
1.
Sub-harness
2.
Band clip
3.
Rear final drive assembly
4.
Connector clip
5.
Electric controlled coupling (right)
6.
Reamer bolt
7.
Electric controlled coupling (left)
A.
Gear carrier mounting face
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply Genuine Liquid Gasket, Three Bond 1217 or equivalent.
JSDIA2237GB
JSDIA2135ZZ
JSDIA2136ZZ
Revision: 2011 October
2012 JUKE
DLN-146
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
6.
Remove final drive mounting bolts and nuts (
) with power tool.
7.
Lower rear final drive assembly to the position where electric
controlled coupling connector can be disconnect.
CAUTION:
Secure final drive assembly to a suitable jack while remov-
ing it.
8.
Disconnect electric controlled coupling connector (1) from sub-
harness (2).
9.
Remove electric controlled coupling connector from final drive
assembly.
10. Remove electric controlled coupling from final drive assembly.
11. Remove sub-harness from final drive assembly.
CAUTION:
• Remove sub-harness only when necessary.
• Never damage side oil seal.
INSTALLATION
1.
If remove sub–harness, replace band clip to sub-harness, and then install sub–harness to rear final drive
assembly.
CAUTION:
• Never reuse band clip.
• Check original mounting dimensions to install clip to the original position.
JSDIA2137ZZ
JSDIA2238ZZ
JSDIA2239ZZ
JSDIA2240ZZ
Revision: 2011 October
2012 JUKE
ELECTRIC CONTROLLED COUPLING
DLN-147
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Pin (A) of sub–harness connector clip must be function-
ing certainly as baffle pin.
• Check the area around the rotating object to see that there
is no interference.
2.
Apply liquid gasket (1) to mating surface of coupling cover.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
CAUTION:
• Remove old gasket adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to the mounting surfaces.
• Overlap both ends of the bead for at least 3 mm (0.12 in).
• Apply liquid gasket to grommet as well.
• The width of sealant bend is approximately 3 mm (0.012
in).
• Never allow liquid gasket to contact the unit characteris-
tics (A) of the coupling cover.
3.
Install electric controlled coupling (1) to spline of center stem
with grommet of harness facing upward, temporarily tighten
reamer bolts (2) to the positions shown in the figure.
CAUTION:
Never damage side oil seal.
4.
Tighten reamer bolts and coupling cover mounting bolts to the
specified torque.
CAUTION:
Never allow harness to get caught in the bolt.
JSDIA2525ZZ
JSDIA2241ZZ
JSDIA2572ZZ
A: Left side
B: Right side
: Vehicle front
JSDIA2242GB
Revision: 2011 October
2012 JUKE
DLN-148
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
5.
Replace connector clip from electric controlled coupling connec-
tor, and then insert it to final drive assembly.
CAUTION:
• Never reuse connector clip.
• When inserting connector clip to final drive assembly,
never tug harness.
6.
Connect electric controlled coupling connector (1) to sub-har-
ness (2).
7.
Install rear drive shaft. Refer to
RAX-17, "Removal and Installa-
CAUTION:
Never damage electric controlled coupling oil seal.
8.
Install propeller shaft assembly. Refer to
9.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
10. When replacing electric controlled coupling, perform writing unit
characteristics after installing rear final drive assembly to the vehicle. Refer to
.
CAUTION:
Always writing unit characteristics of both side electric controlled couplings.
JSDIA2239ZZ
JSDIA2238ZZ
Revision: 2011 October
2012 JUKE
ELECTRIC CONTROLLED COUPLING OIL SEAL
DLN-149
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ELECTRIC CONTROLLED COUPLING OIL SEAL
Exploded View
INFOID:0000000007580298
Removal and Installation
INFOID:0000000007580299
REMOVAL
1.
Remove rear drive shafts. Refer to
RAX-17, "Removal and Installation"
.
2.
Remove electric controlled coupling oil seal from electric con-
trolled coupling, using the suitable oil seal remover.
CAUTION:
Never damage electric controlled coupling.
INSTALLATION
1.
Using the drift (A) [SST: KV38109700 (
—
)], install elec-
tric controlled coupling oil seal to electric controlled coupling to
electric controlled coupling all the way until SST contact the end.
NOTE:
The use of SST satisfies the mounting dimensions.
CAUTION:
• Always use SST [KV38109700 (
—
)].
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
1.
Rear final drive assembly
2.
Electric controlled coupling oil seal
A.
Oil seal lip
: Always replace after every disassembly.
: Apply multi purpose grease
: Apply gear oil.
JSDIA2243ZZ
JSDIA2244ZZ
JSDIA2245ZZ
Revision: 2011 October
2012 JUKE
DLN-150
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING OIL SEAL
2.
Install rear drive shafts. Refer to
RAX-17, "Removal and Installation"
CAUTION:
Never damage electric controlled coupling oil seal.
Revision: 2011 October
2012 JUKE
REAR FINAL DRIVE ASSEMBLY
DLN-151
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000007580300
Removal and Installation
INFOID:0000000007580301
REMOVAL
1.
Remove rear drive shaft. Refer to
RAX-17, "Removal and Installation"
2.
Disconnect sub-harness connector (1).
3.
Remove propeller shaft assembly. Refer to
4.
Support rear final drive assembly with a suitable jack.
1.
Final drive mounting bracket
2.
Washer
3.
Rear final drive assembly
: Vehicle front
: Always replace after every disassembly
: N·m (kg-m, ft-lb)
: Apply multi purpose grease
: Apply gear oil.
JSDIA2134GB
JSDIA2135ZZ
Revision: 2011 October
2012 JUKE
DLN-152
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
REAR FINAL DRIVE ASSEMBLY
5.
Remove rear final drive mounting bolt (
) at rear suspension
member.
6.
Remove final drive mounting bolts and nuts (
) with power tool,
and then remove rear final drive assembly from final drive
mounting bracket.
CAUTION:
Secure final drive assembly to a suitable jack while remov-
ing it.
7.
Remove rear final drive breather hose.
8.
Remove fuel tank. Refer to
FL-22, "AWD : Removal and Installa-
9.
Remove final drive mounting bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• If remove breather hose, install breather hose as following.
- Insert breather hose (1) of final drive side to breather tube (2) until
hose end reaches the tube bent R portion.
- Install the breather to breather hose until hose end reaches the
breather.
- Install hose clamp (1) until dimension (A) shown as follows.
CAUTION:
• Never reuse hose clamps.
• Install the hose clamps, with the tab facing vehicle rear.
JSDIA2136ZZ
JSDIA2137ZZ
(3): Breather
JSDIA2468ZZ
Dimension A
: 5 mm (0.20 in)
JSDIA2531ZZ
Revision: 2011 October
2012 JUKE
REAR FINAL DRIVE ASSEMBLY
DLN-153
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
- Install breather assembly (1) to final drive as shown in the figure.
- Install breather hose with paint mark (A) facing vehicle rear.
• When installing rear drive shaft, never damage electric controlled
coupling oil seal.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
• When replacing rear final drive assembly or electric controlled cou-
pling, perform writing unit characteristics after installing rear final
drive assembly to the vehicle. Refer to
CAUTION:
Always writing unit characteristics of both side electric controlled couplings.
(A): Paint mark
: Vehicle front
JSDIA2138ZZ
Revision: 2011 October
2012 JUKE
DLN-154
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
UNIT DISASSEMBLY AND ASSEMBLY
ELECTRIC CONTROLLED COUPLING
Exploded View
INFOID:0000000007580302
1.
Filler plug
2.
Gasket
3.
Drain plug
4.
Breather tube
5.
Hose clamp
6.
Breather hose
7.
Breather
8.
Band clip
9.
Sub-harness
10. Rear cover
11.
Center stem
12. Side bearing (right)
13. Side bearing adjusting shim (right)
14. Side oil seal (right)
15. Connector clip
16. Electric controlled coupling (right)
17. Electric controlled coupling oil seal
18. Reamer bolt
19. Drive pinion
20. Drive pinion adjusting shim
21. Pinion bearing (rear)
22. Collapsible spacer
23. Breather
24. Gear carrier
25. Carrier bracket (right)
26. Pinion bearing (front)
27. Front oil seal
28. Companion flange
29. Drive pinion lock nut
30. Carrier bracket (left)
31. Drive gear
32. Side bearing (left)
33. Side bearing adjusting shim (left)
34. Side oil seal (left)
35. Electric controlled coupling (left)
A.
Oil seal lip
B.
Gear carrier mounting face
: Always replace after every disassembly.
: Select with proper thickness.
: N·m (kg-m, ft-lb)
: Apply multi purpose grease
: Apply gear oil.
JSDIA2246GB
Revision: 2011 October
2012 JUKE
ELECTRIC CONTROLLED COUPLING
DLN-155
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000007580303
1.
Disconnect electric controlled coupling connector (1) from sub-
harness (2).
2.
Remove electric controlled coupling connector from final drive
assembly.
3.
Remove electric controlled coupling from final drive assembly.
CAUTION:
Never damage side oil seal.
4.
Remove sub-harness from final drive assembly.
CAUTION:
Remove sub-harness only when necessary.
5.
Remove electric controlled coupling oil seal from electric con-
trolled coupling, using the suitable oil seal remover.
CAUTION:
Never damage electric controlled coupling.
: Apply anti-corrosive oil.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
JSDIA2238ZZ
JSDIA2239ZZ
JSDIA2474ZZ
JSDIA2571ZZ
Revision: 2011 October
2012 JUKE
DLN-156
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
Assembly
INFOID:0000000007580304
1.
Using the drift (A) [SST: KV38109700 (
—
)], install elec-
tric controlled coupling oil seal to electric controlled coupling to
electric controlled coupling all the way until SST contact the end.
NOTE:
The use of SST satisfies the mounting dimensions.
CAUTION:
• Always use SST [KV38109700 (
—
)].
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
2.
If remove sub–harness, replace band clip to sub-harness, and
then install sub–harness to rear final drive assembly.
CAUTION:
• Never reuse band clip.
• Check original mounting dimensions to install clip to the original position.
• Pin (A) of sub–harness connector clip must be function-
ing certainly as baffle pin.
• Check the area around the rotating object to see that there
is no interference.
3.
Apply liquid gasket (1) to mating surface of coupling cover.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
CAUTION:
• Remove old gasket adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to the mounting surfaces.
• Overlap both ends of the bead for at least 3 mm (0.12 in).
• Apply liquid gasket to grommet as well.
• The width of sealant bend is approximately 3 mm (0.012
in).
• Never allow liquid gasket to contact the unit characteris-
tics (A or B) of the coupling cover.
JSDIA2301ZZ
JSDIA2525ZZ
JSDIA2241ZZ
JSDIA2572ZZ
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст