Nissan Juke (2012 year). Service Repair Manual — part 204
SR-4
< BASIC INSPECTION >
COLLISION DIAGNOSIS
BASIC INSPECTION
COLLISION DIAGNOSIS
FOR FRONTAL COLLISION
FOR FRONTAL COLLISION : When SRS is activated in a collision
INFOID:0000000007578195
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Replace the diagnosis sensor unit.
3.
Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies.
4.
Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
5.
Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner
assemblies.
6.
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to
SRC-11, "On Board Diagnosis Function"
for details. Ensure entire SRS operates properly.
7.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
.
SRS INSPECTION (FOR FRONTAL COLLISION)
Part
Inspection
Driver air bag module
If the driver air bag has deployed:
REPLACE
Install with new fasteners.
Passenger air bag module (if
equipped)
If the passenger air bag has deployed:
REPLACE
Install with new fasteners.
Crash zone sensor
If any of the front air bags or seat belt pre-tensioners* have been activated:
REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Diagnosis sensor unit
If any of the SRS components have been activated:
REPLACE the diagnosis sensor unit.
Install with new fasteners.
Steering wheel
1.
Visually check steering wheel for deformities.
2.
Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
3.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4.
Check steering wheel for excessive free play.
5.
If no damage is found, reinstall.
6.
If damaged
−
REPLACE.
Spiral cable
If the driver front air bag has deployed:
REPLACE the spiral cable.
Occupant classification system
(Passenger seat)
1.
Remove passenger seat assembly.
2.
Check control unit case for dents, cracks of deformities.
3.
Check connectors and pressure sensor tube for damage, and terminals for deformities.
4.
Check seat frame and cushion pan for dents or deformities.
5.
If no damage is found, reinstall seat with new fasteners.
6.
If damaged
−
REPLACE seat cushion assembly with new fasteners.
Revision: 2011 October
2012 JUKE
COLLISION DIAGNOSIS
SR-5
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FOR FRONTAL COLLISION : When SRS is not activated in a collision
INFOID:0000000007578196
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
3.
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to
SRC-11, "On Board Diagnosis Function"
for details. Ensure entire SRS operates properly.
4.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS INSPECTION (FOR FRONTAL COLLISION)
Harness and connectors
1.
Check connectors for poor connection, damage, and terminals for deformities.
2.
Check harness for binding, chafing, cuts, or deformities.
3.
If no damage is found, reinstall the harness and connectors.
4.
If damaged
−
REPLACE the damaged harness. Do not attempt to repair, splice or modify any
SRS harness.
Instrument panel assembly
If the passenger air bag has deployed:
REPLACE the instrument panel assembly. (integrated type)
Part
Inspection
Part
Inspection
Driver air bag module
If the driver air bag has NOT been deployed:
1.
Remove driver air bag module. Check harness cover and connectors for damage, terminals for
deformities, and harness for binding.
2.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install driver air bag module with new fasteners.
Passenger air bag module (if
equipped)
If the passenger air bag has NOT been deployed:
1.
Remove passenger air bag module. Check harness cover and connectors for damage, termi-
nals for deformities, and harness for binding.
2.
Install passenger air bag module into the instrument panel to check fit with the instrument panel.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install passenger air bag modules with new fasteners.
Crash zone sensor
If the front air bags or seat belt pre-tensioners have NOT been activated:
1.
Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.
2.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor
and bracket.
3.
Install the crash zone sensor to check fit.
4.
If no damage is found, reinstall with new fasteners.
5.
If damaged
−
REPLACE the crash zone sensor and bracket with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If the pre-tensioners have NOT been activated:
1.
Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
2.
Check belts for damage and anchors for loose mounting.
3.
Check retractor for smooth operation.
4.
Check seat belt adjuster for damage.
5.
Check for deformities of the center pillar inner.
6.
If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7.
If no damage is found, reinstall seat belt pre-tensioner assembly.
8.
If damaged
−
REPLACE. Install the seat belt pre-tensioners with new fasteners.
Revision: 2011 October
2012 JUKE
SR-6
< BASIC INSPECTION >
COLLISION DIAGNOSIS
FOR SIDE AND ROLLOVER COLLISION
FOR SIDE AND ROLLOVER COLLISION : When SRS is activated in a collision
INFOID:0000000007578197
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated)
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Satellite sensor LH/RH (on the side on which side air bag is activated)
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies
3.
Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)
4.
Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to
SRC-11, "On Board Diagnosis Function"
for details. Make sure entire SRS operates properly.
5.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
.
Diagnosis sensor unit
If none of the SRS components have been activated:
1.
Check case for dents, cracks or deformities.
2.
Check connectors for damage, and terminals for deformities.
3.
If no damage is found, reinstall with new fasteners.
4.
If damaged
−
REPLACE. Install diagnosis sensor unit with new fasteners.
Steering wheel
1.
Visually check steering wheel for deformities.
2.
Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
3.
Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4.
Check steering wheel for excessive free play.
5.
If no damage is found, reinstall.
6.
If damaged
−
REPLACE.
Spiral cable
If the driver front air bag has not deployed:
1.
Visually check spiral cable and combination switch for damage.
2.
Check connectors and protective tape for damage.
3.
Check steering wheel for noise, binding or heavy operation.
4.
If no damage is found, reinstall.
5.
If damaged
−
REPLACE.
Occupant classification system
(Passenger seat)
1.
Remove passenger seat assembly.
2.
Check control unit case for dents, cracks of deformities.
3.
Check connectors and pressure sensor tube for damage, and terminals for deformities.
4.
Check seat frame and cushion pan for dents or deformities.
5.
If no damage is found, reinstall seat with new fasteners.
6.
If damaged
−
REPLACE seat cushion assembly with new fasteners.
Harness and connectors
1.
Check connectors for poor connection, damage, and terminals for deformities.
2.
Check harness for binding, chafing, cuts, or deformities.
3.
If no damage is found, reinstall the harness and connectors.
4.
If damaged
−
REPLACE the damaged harness. Do not attempt to repair, splice or modify any
SRS harness.
Instrument panel assembly
If the passenger air bag has NOT deployed:
1.
Visually check instrument panel assembly for damage.
2.
If no damage is found, reinstall the instrument panel assembly.
3.
If damaged
−
REPLACE the instrument panel assembly.
Part
Inspection
Revision: 2011 October
2012 JUKE
COLLISION DIAGNOSIS
SR-7
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision
INFOID:0000000007578198
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1.
Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2.
Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag
module must be replaced.
3.
Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to
SRC-11, "On Board Diagnosis Function"
for details. Make sure entire SRS operates properly.
4.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
Part
Inspection
Curtain air bag module LH
If the curtain air bag LH has deployed:
REPLACE the curtain air bag module LH.
Install with new fasteners.
Curtain air bag module RH
If the curtain air bag RH has deployed:
REPLACE the curtain air bag module RH.
Install with new fasteners.
Side air bag module LH
If the side air bag LH has deployed:
REPLACE front seatback assembly LH.
Side air bag module RH
If the side air bag RH has deployed:
REPLACE front seatback assembly RH.
Satellite sensor (LH or RH)
If any of the SRS components have deployed:
REPLACE the satellite sensor on the collision side with new fasteners.
Diagnosis sensor unit
If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.
Center inner pillar
1.
Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
2.
If damaged
−
REPAIR the center inner pillar.
Trim/headlining
1.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.
2.
If damaged
−
REPLACE the damaged trim parts.
Door-mounted curtain air bag
module LH
If the door-mounted curtain air bag module LH has deployed:
REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.
Door-mounted curtain air bag
module RH
If the door-mounted curtain air bag module RH has deployed:
REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.
Pop-up roll bar assemblies
If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.
Revision: 2011 October
2012 JUKE
SR-8
< BASIC INSPECTION >
COLLISION DIAGNOSIS
Part
Inspection
Curtain air bag module LH
If the curtain air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.
2.
If damaged
−
Remove the curtain air bag module LH.
3.
Check for visible signs of damage (tears etc.) of the curtain air bag module LH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall the curtain air bag module LH with new fasteners.
6.
If damaged
−
REPLACE the curtain air bag module LH with new fasteners.
Curtain air bag module RH
If the curtain air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.
2.
If damaged
−
Remove the curtain air bag module RH.
3.
Check for visible signs of damage (tears etc.) of the curtain air bag module RH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall the curtain air bag module RH with new fasteners.
6.
If damaged
−
REPLACE the curtain air bag module RH with new fasteners.
Side air bag module LH
If the side air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.
2.
Check harness and connectors for damage, and terminals for deformities.
3.
If damaged
−
REPLACE the front seatback assembly LH.
Side air bag module RH
If the side air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.
2.
Check harness and connectors for damage, and terminals for deformities.
3.
If damaged
−
REPLACE the front seatback assembly RH.
Satellite sensor (LH or RH)
If none of the SRS components have been activated:
1.
Remove the satellite sensor (LH or RH) on the collision side. Check harness connectors for
damage, terminals for deformities, and harness for binding.
2.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the satellite sensor (LH
or RH).
3.
Install the satellite sensor (LH or RH) to check fit.
4.
If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasteners.
5.
If damaged
−
REPLACE the satellite sensor (LH or RH) with new fasteners.
Diagnosis sensor unit
If none of the SRS components have been activated:
1.
Check case and bracket for dents, cracks or deformities.
2.
Check connectors for damage, and terminals for deformities.
3.
If no damage is found, reinstall the diagnosis sensor unit with new fasteners.
4.
If damaged
−
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)
If the pre-tensioners have NOT been activated:
1.
Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
2.
Check belts for damage and anchors for loose mounting.
3.
Check retractor for smooth operation.
4.
Check seat belt adjuster for damage.
5.
Check for deformities of the center pillar inner.
6.
If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7.
If no damage is found, reinstall seat belt pre-tensioner assembly.
8.
If damaged
−
REPLACE. Install the seat belt pre-tensioners with new fasteners.
Seat (with side air bag)
If the front LH or front RH side air bag modules have NOT deployed:
1.
Visually check the seat on the collision side.
2.
Remove the seat on the collision side and check the following for damage and deformities.
-
Harness, connectors and terminals
-
Frame and recliner (for front and rear seat), and also adjuster and slides (for front seat)
3.
If no damage is found, reinstall the seat.
4.
If damaged
−
REPLACE the damaged seat parts using new fasteners. If the front seat back is
damaged, the front seat back assembly must be replaced.
Center inner pillar
1.
Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
2.
If damaged
−
REPAIR the center inner pillar.
Revision: 2011 October
2012 JUKE
COLLISION DIAGNOSIS
SR-9
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Trim/headlining
1.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.
2.
If damaged
−
REPLACE the damaged trim parts.
Door-mounted curtain air bag
module LH
If the door-mounted curtain air bag LH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.
2.
If damaged
−
REPLACE the door finisher LH with new fasteners.
3.
Check for visible signs of damaged (tears etc.) of the door-mounted curtain air bag module LH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall door finisher.
CAUTION:
When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.
6.
If damaged
−
REPLACE the door finisher LH and door-mounted curtain air bag module LH with
new fasteners.
Door-mounted curtain air bag
module RH
If the door-mounted curtain air bag RH has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.
2.
If damaged
−
REPLACE the door finisher RH with new fasteners.
3.
Check for visible signs of damage (tears etc.) of the door-mounted curtain air bag module RH.
4.
Check harness and connectors for damage, and terminals for deformities.
5.
If no damage is found, reinstall door finisher.
CAUTION:
When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.
6.
If damaged
−
REPLACE the door finisher RH and door-mounted curtain air bag module RH with
new fasteners.
Pop-up roll bar
If the pop-up roll bar has NOT deployed:
1.
Check for visible signs of damage (dents, tears, deformation, etc.) of the pop-up roll bar.
2.
If damaged
−
REPLACE the pop-up roll bar with new fasteners.
3.
Check harness and connectors for damage, and terminals for deformities.
4.
If no damage is found, reinstall the pop-up roll bar with new fasteners.
5.
Check for visible signs of damage (dents, cracks, deformation, etc.) of the seatback support
brace assembly.
6.
If damaged
−
REPAIR the seatback support brace assembly.
Part
Inspection
Revision: 2011 October
2012 JUKE
SR-10
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Exploded View
INFOID:0000000007578199
Removal and Installation
INFOID:0000000007578200
WARNING:
1.
Steering column upper cover
2.
Steering column assembly
3.
Steering column lower cover
4.
Side lid LH
5.
TORX bolt
6.
Driver air bag module
7.
TORX bolt
8.
Side lid RH
9.
Steering wheel
10.
Spiral cable
11. Steering angle sensor
12. Combination switch
13.
Steering switch
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMHIA1655GB
Revision: 2011 October
2012 JUKE
DRIVER AIR BAG MODULE
SR-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove side lid (LH and RH).
Insert flat-bladed screwdriver between side lid and steering
wheel to disengage pawls as shown in the figure.
2.
Remove TORX bolts (LH and RH) from the steering wheel lower side.
3.
Pull out driver air bag module.
4.
Disconnect spiral cable harness connector (A).
5.
Disconnect driver air bag harness connector (B).
CAUTION:
• For installing/removing the driver air bag module harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
6.
Remove driver air bag module.
CAUTION:
• Always place the driver air bag module with pad side facing
upward.
: Pawl
JMHIA1605ZZ
JMHIA1606ZZ
PHIA0953J
: Upward
JMHIA1607ZZ
Revision: 2011 October
2012 JUKE
SR-12
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
• Never impact the driver air bag module.
• Replace the driver air bag module if it has been dropped or
sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old TORX bolts after removal, replace with the new TORX bolts.
• Fix the driver air bag module harnesses to the harness fixing
hook (A).
• Never damage the harness while installing.
• Tighten the TORX bolts after completely adjusting the centers of fixing holes on the driver air bag
module side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged
and the module is not installed securely.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is complete, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
JMHIA1608ZZ
Revision: 2011 October
2012 JUKE
SPIRAL CABLE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000007578201
Removal and Installation
INFOID:0000000007578202
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
1.
Steering column upper cover
2.
Steering column assembly
3.
Steering column lower cover
4.
Side lid LH
5.
TORX bolt
6.
Driver air bag module
7.
TORX bolt
8.
Side lid RH
9.
Steering wheel
10.
Spiral cable
11. Steering angle sensor
12. Combination switch
13.
Steering switch
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMHIA1655GB
Revision: 2011 October
2012 JUKE
SR-14
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
REMOVAL
1.
Remove driver air bag module. Refer to
SR-10, "Removal and Installation"
.
2.
Remove steering wheel. Refer to
ST-8, "Removal and Installation"
3.
Remove steering column upper cover and steering column lower cover. Refer to
.
4.
Disconnect the spiral cable body side harness connectors (A),
(B) and steering angle sensor harness connectors (C).
NOTE:
Disconnect the spiral cable body side harness connector (B)
after removing the spiral cable (A).
5.
6.
Remove the spiral cable fixing screws.
7.
Remove the spiral cable fixing pawls with remover tool (A).
CAUTION:
Remove pawls slowly so that they are not damaged.
8.
Remove the steering angle sensor. Refer to
BRC-135, "Removal and Installation"
.
CAUTION:
• Never impact the spiral cable.
• Replace the spiral cable if it is dropped or sustains an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
JMHIA1656ZZ
: Pawl
JMHIA1610ZZ
JMHIA0009ZZ
Revision: 2011 October
2012 JUKE
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as per the following.
• Carefully turn the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) when the stopper insertion holes
are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond the number of
turns required. (This causes the cable to snap)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
• Fix the driver air bag module harnesses to the harness fixing
hook (A).
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0879ZZ
JMHIA1608ZZ
Revision: 2011 October
2012 JUKE
SR-16
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG MODULE
PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000007578203
Removal and Installation
INFOID:0000000007578204
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1.
Remove instrument side finisher RH, glove box lid, and glove box assembly. Refer to
.
1.
Passenger air bag module
2.
Instrument panel assembly
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA1657GB
Revision: 2011 October
2012 JUKE
PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Disconnect passenger air bag module harness connector (A)
from passenger air bag module.
3.
Remove passenger air bag module fixing bolts (B).
4.
Put a hand to back of instrument panel (glove box opening), dis-
engage connections of the passenger air bag module pawls
from the inside of the vehicle toward the outside, and remove.
CAUTION:
• Never insert a remover tool between passenger air bag
module and instrument panel assembly. Doing so may
cause damage.
• Wear gloves.
CAUTION:
• Always place the passenger air bag module with pad side fac-
ing upward.
• Never impact the passenger air bag module.
• Replace the passenger air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Never disassemble the passenger air bag module.
• Never expose the passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the passenger air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
JMHIA1658ZZ
: Pawl
JMHIA1659ZZ
: Upward
JMHIA1613ZZ
JMHIA0009ZZ
Revision: 2011 October
2012 JUKE
SR-18
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG MODULE
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2011 October
2012 JUKE
CURTAIN AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000007578205
Removal and Installation
INFOID:0000000007578206
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of curtain air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove headlining assembly.
• Normal roof models: Refer to
INT-26, "NORMAL ROOF : Removal and Installation"
.
• Sunroof models: Refer to
INT-29, "SUNROOF : Removal and Installation"
2.
Remove the curtain air bag module mounting bolt that is located on the front pillar.
1.
Curtain air bag module
: Metal clip
: N·m (kg-m, ft-lb)
JMHIA1614GB
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст