Nissan Juke (2012 year). Service Repair Manual — part 31
ABS WARNING LAMP
BRC-115
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS WARNING LAMP
Component Function Check
INFOID:0000000007576867
1.
CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
BRC-115, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000007576868
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to
BRC-108, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK ABS WARNING LAMP SIGNAL
With CONSULT
1.
Select “ABS”, “DATA MONITOR” and “ABS WARN LAMP” according to this order.
2.
Turn the ignition switch OFF.
3.
Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
NO
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-132, "Removal and Installa-
.
Revision: 2011 October
2012 JUKE
BRC-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
BRAKE WARNING LAMP
BRAKE WARNING LAMP
Component Function Check
INFOID:0000000007576869
1.
CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to
BRC-116, "Diagnosis Procedure"
2.
CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
NOTE:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the parking brake switch system. Refer to
BRC-111, "Diagnosis Procedure"
.
3.
CHECK BRAKE WARNING LAMP FUNCTION (3)
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated
while brake fluid level in reservoir tank is with the specified level.
NOTE:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is
ON).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check the brake fluid level switch system. Refer to
Diagnosis Procedure
INFOID:0000000007576870
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to
BRC-108, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK COMBINATION METER
Check the combination meter. Refer to
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-132, "Removal and Installa-
.
NO
>> Repair or replace combination meter. Refer to
MWI-53, "Removal and Installation"
Revision: 2011 October
2012 JUKE
VDC WARNING LAMP
BRC-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC WARNING LAMP
Component Function Check
INFOID:0000000007576871
1.
CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
BRC-117, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000007576872
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to
BRC-108, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK VDC WARNING LAMP SIGNAL
With CONSULT
1.
Select “ABS”, “DATA MONITOR” and “SLIP/VDC LAMP” according to this order.
2.
Turn the ignition switch OFF.
3.
Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
NO
>> Replace ABS actuator and electric unit (control unit). Refer to
MWI-53, "Removal and Installa-
.
Revision: 2011 October
2012 JUKE
BRC-118
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function Check
INFOID:0000000007576873
1.
CHECK VDC OFF INDICATOR LAMP FUNCTION (1)
Check that VDC OFF indicator lamp in combination meter turns ON for approx. 1 second after ignition switch
is turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to diagnosis procedure. Refer to
BRC-118, "Diagnosis Procedure"
2.
CHECK VDC OFF INDICATOR LAMP FUNCTION (2)
Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check the VDC OFF switch system. Refer to
BRC-113, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000007576874
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to
BRC-108, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK VDC OFF INDICATOR LAMP SIGNAL (1)
With CONSULT
1.
Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.
2.
Turn the ignition switch OFF.
3.
Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-132, "Removal and Installa-
.
3.
CHECK VDC OFF INDICATOR LAMP SIGNAL (2)
With CONSULT
1.
Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.
2.
Check that data monitor displays “On” or “Off” each time when VDC OFF switch is operated.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
NO
>> Check the VDC OFF switch system. Refer to
MWI-53, "Removal and Installation"
Revision: 2011 October
2012 JUKE
EXCESSIVE OPERATION FREQUENCY
BRC-119
< SYMPTOM DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SYMPTOM DIAGNOSIS
EXCESSIVE OPERATION FREQUENCY
Description
INFOID:0000000007576875
VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function
operates in excessive operation frequency.
Diagnosis Procedure
INFOID:0000000007576876
1.
CHECK BRAKING FORCE
Check the brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check the brake system.
2.
CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
• Front axle: Refer to
• Rear axle
- 2WD: Refer to
.
- AWD: Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK WHEEL SENSOR
Check the wheel sensor.
• Check installation and damage of wheel sensor.
• Check connection of wheel sensor harness connector.
• Check terminal of wheel sensor harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>>
Repair or replace wheel sensor.
• Front wheel sensor: Refer to
BRC-126, "FRONT WHEEL SENSOR : Removal and Installation"
• Rear wheel sensor: Refer to
BRC-129, "REAR WHEEL SENSOR : Removal and Installation"
4.
CHECK SENSOR ROTOR
Check that there is no looseness, damage or foreign material on sensor rotor.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>>
Repair installation or replace sensor rotor.
• Front sensor rotor: Refer to
BRC-131, "FRONT SENSOR ROTOR : Removal and Installation"
.
• Rear sensor rotor. Refer to
BRC-131, "REAR SENSOR ROTOR : Removal and Installation"
5.
CHECK WARNING LAMP TURNS OFF
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after
key switch is turned ON and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES
>> Normal
NO
>> Perform self-diagnosis for “ABS” with CONSULT.
Revision: 2011 October
2012 JUKE
BRC-120
< SYMPTOM DIAGNOSIS >
[WITH VDC]
UNEXPECTED BRAKE PEDAL REACTION
UNEXPECTED BRAKE PEDAL REACTION
Description
INFOID:0000000007576877
A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed.
Diagnosis Procedure
INFOID:0000000007576878
1.
CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
• Front axle: Refer to
• Rear axle
- 2WD: Refer to
.
- AWD: Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK DISC ROTOR
Check the disc rotor runout.
• Front: Refer to
BR-14, "DISC ROTOR : Inspection and Adjustment"
.
• Rear: Refer to
BR-16, "DISC ROTOR : Inspection and Adjustment"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>>
Refinish disc rotor.
• Front: Refer to
BR-14, "DISC ROTOR : Inspection and Adjustment"
.
• Rear: Refer to
BR-16, "DISC ROTOR : Inspection and Adjustment"
3.
CHECK BRAKE FLUID LEAKAGE
Check the fluid leakage.
• Front: Refer to
• Rear: Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK BRAKE PEDAL
Check the each item of brake pedal. Refer to
BR-7, "Inspection and Adjustment"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Adjust each item of brake pedal. Refer to
BR-7, "Inspection and Adjustment"
5.
CHECK BRAKING FORCE
Check the brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Check the each components of brake system.
6.
CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) harness connector so that ABS does not operate.
Check that brake force is normal in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES
>> Normal
NO
>> Check the each components of brake system.
Revision: 2011 October
2012 JUKE
THE BRAKING DISTANCE IS LONG
BRC-121
< SYMPTOM DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
THE BRAKING DISTANCE IS LONG
Description
INFOID:0000000007576879
Brake stopping distance is long when ABS function is operated.
Diagnosis Procedure
INFOID:0000000007576880
CAUTION:
Brake stopping distance on slippery road like rough road, gravel road or snowy road may become
longer when ABS is operated than when ABS is not operated.
1.
CHECK BRAKING FORCE
Check the brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check the each components of brake system.
2.
CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) harness connector so that ABS does not operate.
Check the brake stopping distance in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES
>> Normal
NO
>> Check the each components of brake system.
Revision: 2011 October
2012 JUKE
BRC-122
< SYMPTOM DIAGNOSIS >
[WITH VDC]
DOES NOT OPERATE
DOES NOT OPERATE
Description
INFOID:0000000007576881
VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function
does not operate.
Diagnosis Procedure
INFOID:0000000007576882
CAUTION:
• VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD)
function never operate when the vehicle speed is 10 km/h (6.2 MPH) or less.
• VDC function and TCS function never operate when VDC OFF switch is operated (when VDC OFF
indicator lamp turns ON).
1.
CHECK WARNING LAMP
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning
lamp and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES
>> Normal
NO
>> Perform self-diagnosis for “ABS” with CONSULT.
Revision: 2011 October
2012 JUKE
BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS
BRC-123
< SYMPTOM DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS
Description
INFOID:0000000007576883
• Brake pedal vibrates and motor sound from ABS actuator and electric unit (control unit) occurs, when the
engine starts.
• Brake pedal vibrates during braking.
CAUTION:
Vibration may be felt during brake pedal is lightly depressed (just placing a foot on it) in the following
conditions. This is normal.
• When shifting gears
• When driving on slippery road
• During cornering at high speed
• When passing over bumps or grooves [Approx. 50 mm (1.97 in) or more]
• When pulling away just after starting engine [at approx. 10 km/h (6.2 MPH) or higher]
Diagnosis Procedure
INFOID:0000000007576884
1.
SYMPTOM CHECK 1
Check that there are pedal vibrations when the engine is started.
Do vibrations occur?
YES
>> GO TO 2.
NO
>> Check brake pedal. Refer to
BR-19, "Inspection and Adjustment"
.
2.
SYMPTOM CHECK 2
Check that motor noise from ABS actuator and electric unit (control unit) occurs when the engine starts.
Does the operation sound occur?
YES
>> GO TO 3.
NO
>> Perform self-diagnosis for “ABS” with CONSULT.
3.
SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Does the symptom occur?
YES
>> Check that radio (including wiring), antenna and antenna lead-in wires are not located near ABS
actuator and electric unit (control unit). Move them if they are located near ABS actuator and elec-
tric unit (control unit).
NO
>> Normal
Revision: 2011 October
2012 JUKE
BRC-124
< SYMPTOM DIAGNOSIS >
[WITH VDC]
VEHICLE JERKS DURING
VEHICLE JERKS DURING
Description
INFOID:0000000007576885
The vehicle jerks when VDC function, TCS function, ABS function, EBD function or brake limited slip differen-
tial (BLSD) function operates.
Diagnosis Procedure
INFOID:0000000007576886
1.
CHECK SYMPTOM
Check that the vehicle jerks when VDC function, TCS function, ABS function, EBD function or brake limited
slip differential (BLSD) function operates.
Is the inspection result normal?
YES
>> Normal
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK CONNECTOR
With CONSULT
1.
Turn the ignition switch OFF.
2.
Disconnect ABS actuator and electric unit (control unit) harness connector.
3.
Check connector terminal for deformation, disconnection and looseness.
4.
Connect harness connector and perform self-diagnosis for “ABS” again.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Poor connection of connector terminal. Repair or replace connector terminal.
4.
CHECK ECM AND TCM SELF-DIAGNOSIS RESULTS
With CONSULT
Perform self-diagnosis for “ENGINE” and “TRANSMISSION” (for CVT models).
Is any DTC detected?
YES
>> Check the DTC.
NO
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-132, "Removal and Installa-
.
Revision: 2011 October
2012 JUKE
NORMAL OPERATING CONDITION
BRC-125
< SYMPTOM DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000007576887
Symptom
Result
Brake pedal slightly vibrates and operation sound (motor sound and sound from suspen-
sion) occurs when VDC function, TCS function, ABS function, EBD function or brake limited
differential (BLSD) function operates.
This is not a malfunction, The symptom
occurs VDC function, TCS function, ABS
function, EBD function and brake limited
differential (BLSD) function that are nor-
mally operated.
Brake stopping distance may become longer than models without ABS function depending
on the road conditions, when ABS function is operated on slippery road like rough road,
gravel road or snowy road.
Brake pedal vibrates and operation sound occurs during sudden acceleration and corner-
ing, when VDC function, TCS function or brake limited slip differential (BLSD) function is
operated.
Brake pedal vibrates and motor sound from the engine room occurs, when the engine starts
or the vehicle starts just after starting the engine.
This is not a malfunction, because it is
caused by operation check of ABS actua-
tor and electric unit (control unit).
Acceleration may be felt insufficient depending on the road conditions.
This is not a malfunction, because it is
caused by TCS function that puts the
highest priority to obtain the optimum
traction (stability).
TCS function may operate momentarily, while driving on a road where friction coefficient
varies, or when downshifting, or fully depressing accelerator pedal.
ABS warning lamp and VDC OFF indicator lamp may turn ON, when the vehicle is on a ro-
tating turntable or is given a strong shaking or large vibrations on a ship while the engine is
running.
In this case, restart the engine on a nor-
mal road. If the normal condition is re-
stored, there is no malfunction. In that
case, erase “ABS” self-diagnosis result
memory with CONSULT.
VDC warning lamp may turn ON and VDC function, TCS function and brake limited slip dif-
ferential (BLSD) function may not normally operate, when driving on a special road the is
extremely slanted (bank in a circuit course).
A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle
sharply turns during a spin turn, acceleration turn or drift driving while VDC function, TCS
function and brake limited slip differential (BLSD) function are OFF (VDC OFF switch is
pressed and VDC OFF indicator lamp is in ON status).
The vehicle speed does not increase, when the accelerator pedal is depressed while the
vehicle is on a 2-wheel chassis dynamometer for speedometer check.
This is not a malfunction. (When checking
the vehicle on a chassis dynamometer,
operate VDC OFF switch so that TCS
function is OFF.)
Revision: 2011 October
2012 JUKE
BRC-126
< REMOVAL AND INSTALLATION >
[WITH VDC]
WHEEL SENSOR
REMOVAL AND INSTALLATION
WHEEL SENSOR
FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View
INFOID:0000000007576888
NOTE:
Front RH wheel sensor is symmetrically opposite of LH.
FRONT WHEEL SENSOR : Removal and Installation
INFOID:0000000007576889
REMOVAL
1.
Remove tires.
2.
Remove the fender protector (front). Refer to
EXT-21, "Removal and Installation"
3.
Remove front wheel sensor from steering knuckle.
CAUTION:
Never rotate and never pull front wheel sensor as much as possible, when pulling out.
4.
Remove front wheel sensor harness from the vehicle.
CAUTION:
Never twist or pull front wheel sensor harness, when removing.
INSTALLATION
Note the following, and install in the reverse order of the removal.
1.
Front LH wheel sensor
2.
Front LH wheel sensor harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
JPFIC0191GB
Revision: 2011 October
2012 JUKE
WHEEL SENSOR
BRC-127
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Check that there is no foreign material like iron powder or damage on inner surface of front wheel sensor
mounting hole of steering knuckle and sensor rotor. Install after cleaning when there are foreign material like
iron powder, or replace when there is a malfunction.
• Never twist front wheel sensor harness when installing front wheel
sensor. Check that grommet (2) is fully inserted to bracket (1).
Check that front wheel sensor harness is not twisted after installa-
tion.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000007576890
2WD
Left side
JPFIC0209ZZ
JPFIC0192GB
1.
Rear LH wheel sensor
2.
Rear LH wheel sensor harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
Revision: 2011 October
2012 JUKE
BRC-128
< REMOVAL AND INSTALLATION >
[WITH VDC]
WHEEL SENSOR
Right side
AWD
JPFIC0218GB
1.
Rear RH wheel sensor
2.
Rear RH wheel sensor harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
Revision: 2011 October
2012 JUKE
WHEEL SENSOR
BRC-129
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
NOTE:
Rear RH wheel sensor is symmetrically opposite of LH.
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000007576891
REMOVAL
1.
Remove rear wheel sensor from wheel hub and bearing assembly (2WD).
CAUTION:
Never rotate or pull rear wheel sensor as much as possible, when pulling out.
2.
Remove rear wheel sensor from axle housing (AWD).
CAUTION:
Never rotate or pull rear wheel sensor as much as possible, when pulling out.
3.
Remove rear wheel sensor harness from the vehicle.
CAUTION:
Never twist and never pull rear wheel sensor harness, when removing.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Check that there is no foreign material like iron powder or damage on inner surface of rear wheel sensor
mounting hole of wheel hub and bearing assembly and sensor rotor. Install after cleaning when there are for-
eign material like iron powder, or replace when there is a malfunction.
1.
Rear LH wheel sensor
2.
Rear LH wheel sensor harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
JSFIA0525GB
Revision: 2011 October
2012 JUKE
BRC-130
< REMOVAL AND INSTALLATION >
[WITH VDC]
WHEEL SENSOR
• Never twist rear wheel sensor harness when installing rear wheel
sensor. Check that grommet (2) is fully inserted to bracket (1).
Check that rear wheel sensor harness is not twisted after installa-
tion.
CAUTION:
Check that the identification line (A) of the rear wheel sensor
is faced upward.
JPFIC0209ZZ
JPFIC0198ZZ
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст