Nissan Juke (2012 year). Service Repair Manual — part 124
FRONT GRILLE
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Exploded View
INFOID:0000000007578079
Removal and Installation
INFOID:0000000007578080
REMOVAL
CAUTION:
When remove front grilles (1) apply protective tape (A) on the
bumper fascia (2) to protect the painted surface from damage.
1.
Fully open hood assembly.
1.
Bumper fascia assembly
2.
Front side grille RH
3.
Front center grille
4.
Emblem
5.
Front side grille LH
: Pawl
JMKIA5563ZZ
JMKIA5622ZZ
Revision: 2011 October
2012 JUKE
EXT-18
< REMOVAL AND INSTALLATION >
FRONT GRILLE
2.
Remove front center grille upper fixing clips (A).
CAUTION:
Apply protective tape (B) around bumper fascia.
3.
Disengage fixing pawls from back side while pulling front center
grille to wade vehicle front, and then remove front center grille.
4.
Remove front side grille (LH and RH) upper fixing clips (A).
5.
Disengage fixing pawls from back side of front side grille (LH
and RH).
CAUTION:
Apply protective tape (B) around bumper fascia.
6.
Remove front side grille (LH and RH) to ward vehicle front.
7.
Remove emblem after removing front grille.
INSTALLATION
Install in the reverse order of removal.
JMKIA5623ZZ
: Pawl
JMKIA5756ZZ
: Pawl
JMKIA5624ZZ
Revision: 2011 October
2012 JUKE
COWL TOP
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Exploded View
INFOID:0000000007578081
1.
Front fender cover RH
2.
Cowl top cover seal
3.
Cowl top insulator
4.
Blind plug RH
5.
Cowl top cover cap
6.
Cowl top extension
7.
EPT seal [t: 3.0 mm (0.118 in)]
8.
Air intake cover
9.
Cowl top cover
10. Front fender cover LH
11. Washer nozzle
: Clip
JMKIA5940ZZ
Revision: 2011 October
2012 JUKE
EXT-20
< REMOVAL AND INSTALLATION >
COWL TOP
Removal and Installation
INFOID:0000000007578082
REMOVAL
1.
Fully open hood assembly.
2.
Remove front wiper arm (LH and RH). Refer to
WW-54, "Removal and Installation"
3.
Disconnect washer tube joint on cowl top cover RH.
4.
Remove cowl top seal fixing clips, and then remove cowl top seal.
5.
Remove cowl top insulator fixing clips, and then remove cowl top insulator.
6.
Remove front fender cover (LH and RH).
7.
Remove cowl top cover fixing clips.
8.
Pull forward to release cowl top cover from windshield glass.
CAUTION:
When performing the procedure after removing cowl top
cover, cover the lower end of windshield glass with ure-
thane etc.
9.
Remove cowl top cover.
10. Remove the following parts after removing cowl top cover.
• EPT sealer
• Washer tube
• Washer nozzle (LH and RH). Refer to
WW-51, "Removal and Installation"
.
11. Remove front wiper drive assembly. Refer to
WW-59, "Removal and Installation"
12. Remove cowl top extension mounting bolts, and then remove cowl top extension.
INSTALLATION
Note the following items and then, install in the reverse order of removal.
CAUTION:
• Clean the joint between the cowl top cover and the windshield, and then install them.
• Replace the EPT sealer on the back surface with new EPT sealer when reusing the cowl top cover.
• Remove the EPT sealer remaining on the cowl top cover using a double-faced adhesive tape remove.
• To maintain adhesion, never wash the vehicle within 24 hours after installation.
• Perform the stop position adjustment at the installation of the front wiper arms. Refer to
.
: Pawl
: Do not reuse
JMKIA5621ZZ
Revision: 2011 October
2012 JUKE
FENDER PROTECTOR
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
Exploded View
INFOID:0000000007578083
Removal and Installation
INFOID:0000000007578084
REMOVAL
1.
Remove front fillet molding. Refer to
EXT-25, "FRONT FILLET MOLDING : Removal and Installation"
.
2.
Remove air guide fixing bolts, and then remove air guide.
3.
Remove front fender protector mounting screws and clips.
4.
Remove front fender protector from wheel house.
INSTALLATION
Install in the reverse order of removal.
1.
Hoodledge insurator
2.
Fender protector
3.
U nut
4.
Air guide
5.
Screw grommet
A.
To hoodledge panel
: Vehicle front
JMKIA5651ZZ
Revision: 2011 October
2012 JUKE
EXT-22
< REMOVAL AND INSTALLATION >
SILL COVER
SILL COVER
Exploded View
INFOID:0000000007578085
Removal and Installation
INFOID:0000000007578086
REMOVAL
1.
Remove sill cover front end fixing screw (A).
1.
Screw grommet
2.
Screw grommet
3.
Sill cover
4.
Wind deflector
JMKIA5581ZZ
JMKIA5565ZZ
Revision: 2011 October
2012 JUKE
SILL COVER
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Remove sill cover rear end fixing screw (A).
3.
Remove sill cover lower side fixing screws.
4.
Fully open front door and rear door.
5.
Remove clips from sill cover back side with a remover tool (A).
CAUTION:
Apply protective tape (B) on the body to protect the painted
surface from damage.
6.
Remove sill cover form body side.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing sill cover, check that clips are securely fitted in body panel holes, and then press clips
in.
JMKIA5566ZZ
: Clip
JMKIA5567ZZ
Revision: 2011 October
2012 JUKE
EXT-24
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
FLOOR SIDE FAIRING
Exploded View
INFOID:0000000007578087
Removal and Installation
INFOID:0000000007578088
REMOVAL
FLOOR UNDER COVER
Remove floor under cover mounting nut and push spring nuts, and then remove floor under cover.
INSTALLATION
Install in the reverse order of removal.
1.
Push spring nut
2.
Floor under cover RH
3.
Floor under cover LH
JMKIA5648ZZ
Revision: 2011 October
2012 JUKE
FILLET MOLDING
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FILLET MOLDING
Exploded View
INFOID:0000000007578089
FRONT FILLET MOLDING
FRONT FILLET MOLDING : Removal and Installation
INFOID:0000000007578090
REMOVAL
1.
Remove front fillet molding fixing clips.
2.
Remove front fillet molding front side fixing pawls.
1.
Grommet
2.
Clip
3.
Clip
4.
Front fillet molding
5.
Rear fillet molding
: Pawl
: Do not reuse
JMKIA5582ZZ
: Pawl
JMKIA5583ZZ
Revision: 2011 October
2012 JUKE
EXT-26
< REMOVAL AND INSTALLATION >
FILLET MOLDING
3.
Using remover tool (A), disengage the clips from front fillet mold-
ing by starting from front side.
CAUTION:
• Apply a protective tape (B) on the body to protect the
painted surface from damage.
• Never pull fillet molding strongly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always replace fillet molding fixing clips.
• When installing front fillet molding, check that blind clips and pawls are securely fitted in panel holes
on body, and then press them in.
REAR FILLET MOLDING
REAR FILLET MOLDING : Removal and Installation
INFOID:0000000007578091
REMOVAL
1.
Remove filet molding fixing clip from end of sill cover.
2.
Remove rear fillet molding rear side fixing pawls.
CAUTION:
Never pull the rear fillet molding strongly.
3.
Using remover tool (A), disengage the clips from rear fillet mold-
ing by starting from rear side.
CAUTION:
• Apply a protective tape (B) on the body to protect the
painted surface from damage.
• Never pull the rear fillet molding strongly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always replace fillet molding fixing clips.
• When installing rear fillet molding, check that blind clips and pawls are securely fitted in panel holes
on body, and then press them in.
: Clip
JMKIA5584ZZ
: Pawl
JMKIA5585ZZ
: Clip
JMKIA5586ZZ
Revision: 2011 October
2012 JUKE
ROOF SIDE MOLDING
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000007578092
Removal and Installation
INFOID:0000000007578093
REMOVAL
ROOF SIDE MODLDING
1.
Disengage roof side molding rear side fixing clip, using a
remover tool (A).
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
1.
Roof side molding
2.
Roof side molding clip
3.
Double-sided tape [t: 2.5 mm (0.098 in)]
4.
Body side outer panel
5.
Roof panel
: Vehicle front
: Do not reuse
JMKIA5649ZZ
: Clip
: Vehicle front
JMKIA5770ZZ
Revision: 2011 October
2012 JUKE
EXT-28
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
2.
Pull up roof side molding from rear end to front end.
CAUTION:
Never pull the roof side molding strongly.
3.
Disengage windshield molding and clip at the front end of roof
side molding, and then remove while pulling out toward vehicle
rear.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
REMOVAL
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
INSTALLATION
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape roof side molding clips after press fit, and temporarily hold it for specified time based on the follow-
ing.
CAUTION:
• Use double-sided tape after hardening for roof side molding clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield glass portion, check that body side molding fas-
tener is securely inserted and then press in.
: Vehicle front
JMKIA3884ZZ
: Clip
JMKIA5650ZZ
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Revision: 2011 October
2012 JUKE
ROOF SIDE MOLDING
EXT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Never wash the vehicle within 24 hours so as to keep adhesive.
Revision: 2011 October
2012 JUKE
EXT-30
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000007578094
FRONT DOOR OUTSIDE MOLDING
FRONT DOOR OUTSIDE MOLDING : Removal and Installation
INFOID:0000000007578095
REMOVAL
1.
Fully open front door glass.
2.
Twist door outside molding toward the outside of the vehicle,
and then lift up and remove it while disengaging the pawls.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
1.
Front door panel
2.
Front door outside molding
3.
Rear door panel
4.
Rear door outside molding
5.
Door glass
: Pawl
JMKIA5664GB
JMKIA5801ZZ
Revision: 2011 October
2012 JUKE
DOOR OUTSIDE MOLDING
EXT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
When installing front door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
REAR DOOR OUTSIDE MOLDING
REAR DOOR OUTSIDE MOLDING : Removal and Installation
INFOID:0000000007578096
REMOVAL
1.
Fully open rear door glass.
2.
Twist rear door outside molding toward vehicle outside and
remove molding while disengaging it from door panel.
3.
Slide rear door outside molding (1) toward vehicle front, and
then pull molding out from rear door handle (2).
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing rear door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
JMKIA5669ZZ
: Pawl
JMKIA5696ZZ
JMKIA5697ZZ
JMKIA5698ZZ
Revision: 2011 October
2012 JUKE
EXT-32
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
DOOR SASH TAPE
Exploded View
INFOID:0000000007578097
FRONT DOOR SASH TAPE
FRONT DOOR SASH TAPE : Removal and Installation
INFOID:0000000007578098
REMOVAL
Heat door sash tape surface using a dryer, and then peel door sash tape.
CAUTION:
Never damage painted surface of door panel.
INSTALLATION
NOTE:
For installation position of door sash tape, refer to the position as shown in the figure.
1.
Front door panel
2.
Front door sash tape
3.
Rear door sash tape
4.
Rear door panel
: Do not reuse
JMKIA5665ZZ
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст