Nissan Juke (2012 year). Service Repair Manual — part 67
U1010 CONTROL UNIT (CAN)
DLN-77
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
U1010 CONTROL UNIT (CAN)
Description
INFOID:0000000007580223
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicate data but selectively reads required data only.
DTC Logic
INFOID:0000000007580224
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “U1010” detected?
YES >> Proceed
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007580225
1.
CHECK AWD CONTROL MODULE
Check AWD control module harness connector for disconnection and deformation.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
U1010
CONTROL UNIT (CAN)
Detecting error during the initial diagno-
sis of CAN controller of AWD control
module.
Internal malfunction of AWD control
module
Revision: 2011 October
2012 JUKE
DLN-78
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000007580226
1.
CHECK AWD CONTROL MODULE POWER SUPPLY (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control module harness connector.
3.
Check the voltage between AWD control module harness connector and ground.
4.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
5.
Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AWD CONTROL MODULE POWER SUPPLY (2)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#33).
3.
Check the harness for open or short between AWD control module harness connector No.1 terminal and
10A (#33).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY (3)
1.
Turn the ignition switch OFF.
2.
Check the voltage between AWD control module harness connector and ground.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
4.
Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
0 V
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
11 – 13 V
Revision: 2011 October
2012 JUKE
POWER SUPPLY AND GROUND CIRCUIT
DLN-79
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
CHECK AWD CONTROL MODULE POWER SUPPLY (4)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#3).
3.
Check the harness for open or short between AWD control module harness connector No.3 terminal and
10A (#3).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for ignition power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
5.
CHECK AWD SOLENOID POWER SUPPLY (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control module harness connector.
3.
Check the voltage between AWD control module harness connector and ground.
4.
Turn the ignition switch OFF to ON.
CAUTION:
Never start the engine.
5.
Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK AWD SOLENOID POWER SUPPLY (2)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#12).
3.
Check the harness for open or short between AWD control module harness connector No.12 and the 10A
fuse (#12).
Is the inspection result normal?
YES
>> Perform the trouble the diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
7.
CHECK AWD CONTROL MODULE GROUND
1.
Turn the ignition switch OFF.
2.
Check the continuity between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace error-detected parts.
AWD control module
—
Voltage
Connector
Terminal
B47
12
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
12
Ground
11 – 13 V
AWD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
Revision: 2011 October
2012 JUKE
DLN-80
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP
AWD WARNING LAMP
Component Function Check
INFOID:0000000007580227
1.
CHECK AWD WARNING LAMP FUNCTION
Check that AWD warning lamp turns ON when turn the ignition switch ON. Then, AWD warning lamp turns
OFF approx. 1 second after the engine start.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000007580228
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK AWD WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check “WARNING LAMP” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “On”?
YES
>> Perform the trouble diagnosis for combination meter power supply circuit. Refer to
"COMBINATION METER : Diagnosis Procedure"
.
NO
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
Revision: 2011 October
2012 JUKE
AWD MODE INDICATOR LAMP (AWD-V)
DLN-81
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD MODE INDICATOR LAMP (AWD-V)
Component Function Check
INFOID:0000000007580229
1.
AWD MODE INDICATOR LAMP OPERATION CHECK
1.
Turn the ignition switch ON.
2.
Set AWD mode switch to “AWD-V”.
3.
Check that AWD mode indicator lamp (AWD-V) turns on.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000007580230
1.
CHECK AWD WARNING LAMP
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2.
Stop the vehicle.
Does AWD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD MODE INDICATOR LAMP SIGNAL
With CONSULT
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Change AWD mode switch to “AWD-V” from “2WD”.
3.
Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “AWD-V”?
YES
>> GO TO 4.
NO
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
Revision: 2011 October
2012 JUKE
DLN-82
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
AWD MODE INDICATOR LAMP (AWD)
AWD MODE INDICATOR LAMP (AWD)
Component Function Check
INFOID:0000000007580231
1.
AWD MODE INDICATOR LAMP OPERATION CHECK
Check that AWD mode indicator lamp (AWD) turns on for approximately 1 second after the ignition switch is
turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000007580232
1.
CHECK AWD WARNING LAMP
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2.
Stop the vehicle.
Does AWD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD MODE INDICATOR LAMP SIGNAL
With CONSULT
1.
Start the engine.
CAUTION:
Stop the vehicle.
2.
Change AWD mode switch to “AWD” from “AWD-V”.
3.
Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “AWD”?
YES
>> GO TO 4.
NO
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
Revision: 2011 October
2012 JUKE
AWD WARNING LAMP DOES NOT TURN ON
DLN-83
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SYMPTOM DIAGNOSIS
AWD WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000007580233
AWD warning lamp does not turn ON when the ignition switch is turned to ON.
Diagnosis Procedure
INFOID:0000000007580234
1.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis for AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
Revision: 2011 October
2012 JUKE
DLN-84
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP DOES NOT TURN OFF
AWD WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000007580235
AWD warning lamp does not turn OFF approx. 1 second after the engine started.
Diagnosis Procedure
INFOID:0000000007580236
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis of the AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY AND GRAND CIRCUIT
Perform the trouble diagnosis of power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
Revision: 2011 October
2012 JUKE
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
DLN-85
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
Description
INFOID:0000000007580237
Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.
Diagnosis Procedure
INFOID:0000000007580238
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
(Right side).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the error-detected parts.
4.
CHECK ELECTRIC CONTROLLED COUPLING
1.
Turn the ignition switch OFF.
2.
Set the transaxle to neutral. Release the parking brake.
3.
Lift up the vehicle.
4.
Rotate the propeller shaft by hand.
5.
Hold rear wheel of right and left lightly.
Does rear wheel rotate?
YES
>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Revision: 2011 October
2012 JUKE
DLN-86
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
VEHICLE DOES NOT ENTER AWD MODE
VEHICLE DOES NOT ENTER AWD MODE
Description
INFOID:0000000007580239
Vehicle does not enter 4-wheel drive mode even though AWD warning lamp turned to OFF.
Diagnosis Procedure
INFOID:0000000007580240
1.
CHECK AWD WARNING LAMP
Turn the ignition switch ON.
CAUTION:
Never start the engine.
Does AWD warning lamp turn ON?
YES
>> GO TO 2.
NO
>> Proceed to
.
2.
CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT
Check “PKB SW” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Proceed to
BRC-108, "Diagnosis Procedure"
3.
CRUISE TEST
Drive the vehicle for a period of time.
Does any symptom occur?
YES
>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of
clutch is not possible). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Monitor Item
Condition
Status
PKB SW
When the parking brake switch is operation.
On
When the parking brake switch is not operation.
Off
Revision: 2011 October
2012 JUKE
AWD WARNING LAMP BLINKS QUICKLY
DLN-87
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD WARNING LAMP BLINKS QUICKLY
Description
INFOID:0000000007580241
While driving, AWD warning lamp blinks 2 times in 1 second and it turns OFF after 1 minute.
NOTE:
• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and
multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid
before lamp blinks quickly. Both cases are not malfunction. Refer to
• When this symptom occurs, stop vehicle and allow it to idle for some times. Blinking will stop and system will
be restored.
Revision: 2011 October
2012 JUKE
DLN-88
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP BLINKS SLOWLY
AWD WARNING LAMP BLINKS SLOWLY
Description
INFOID:0000000007580242
AWD warning lamp blinks at approximately 2 seconds intervals while driving.
Diagnosis Procedure
INFOID:0000000007580243
1.
CHECK VEHICLE SPEED SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
2.
Check that each value of “WHEEL SPD SEN FR”, “WHEEL SPD SEN FL”, “WHEEL SPD SEN RR”, and
“WHEEL SPD SEN RL” in “DATA MONITOR” for “ALL MODE AWD/4WD” is almost equal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to
.
2.
CHECK TIRE
Check the following.
• Tire pressure
• Tire wear condition
• Front and rear tire size (There is no difference between front and rear tires.)
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
TERMINAL INSPECTION
Check AWD control module harness connector for disconnection.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-92, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
Revision: 2011 October
2012 JUKE
DECREASE IN TURNING PERFORMANCE
DLN-89
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DECREASE IN TURNING PERFORMANCE
Description
INFOID:0000000007580244
Turning performance decreases when driving in AWD-V mode or AWD mode.
Diagnosis Procedure
INFOID:0000000007580245
1.
PERFORM EPS CONTROL UNIT SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “EPS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
(Right side).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the error-detected parts.
4.
CHECK ELECTRIC CONTROLLED COUPLING
1.
Turn the ignition switch OFF.
2.
Set the transaxle to neutral. Release the parking brake.
3.
Lift up the vehicle.
4.
Rotate the propeller shaft.
5.
Hold the rear wheel of right and left lightly.
Does the rear wheel rotate?
YES
>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Revision: 2011 October
2012 JUKE
DLN-90
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000007580246
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these
parts.
Reference
SUSPECTED PARTS
(Possible cause)
T
R
ANSFER OIL (Level
low
)
T
R
ANSFER OIL (W
rong)
T
R
ANSFER OIL (Level
too high)
LI
QUI
D
GASKET
(Dam
ag
ed
)
OIL
SEAL
(W
orn
or da
ma
ge
d
)
GEAR
(W
orn
o
r
da
ma
ge
d)
B
EARING (W
orn
or
da
ma
ge
d)
Symptom
Noise
1
2
3
3
3
Transfer oil leakage
3
1
2
2
Revision: 2011 October
2012 JUKE
TRANSFER OIL
DLN-91
< PERIODIC MAINTENANCE >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PERIODIC MAINTENANCE
TRANSFER OIL
Inspection
INFOID:0000000007580247
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug (1) and gasket. Then check that oil is filled up
from mounting hole for the filler plug.
CAUTION:
Never start engine while checking oil level.
2.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000007580248
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the engine and remove the drain plug (1) and gasket to
drain the transfer oil.
3.
Before installing drain plug, set a new gasket. Install drain plug
on the transfer and tighten to the specified torque. Refer to
.
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000007580249
1.
Remove filler plug (1) and gasket. Then fill oil up to mounting
hole for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified
torque. Refer to
CAUTION:
Never reuse gasket.
: Vehicle front
JSDIA2080ZZ
: Vehicle front
JSDIA2081ZZ
: Vehicle front
Oil and viscosity
: Refer to
.
Oil capacity
: Refer to
.
JSDIA2080ZZ
Revision: 2011 October
2012 JUKE
DLN-92
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
AWD CONTROL MODULE
REMOVAL AND INSTALLATION
AWD CONTROL MODULE
Exploded View
INFOID:0000000007580250
Removal and Installation
INFOID:0000000007580251
REMOVAL
1.
Turn the ignition switch OFF.
2.
Remove front seat (left side). Refer to
SE-18, "Removal and Installation"
.
3.
Remove dush side finisher (left side). Refer to
INT-20, "DASH SIDE FINISHER : Removal and Installa-
4.
Remove front and rear kicking plate inner. Refer to
INT-18, "KICKING PLATE INNER : Removal and
.
5.
Remove rear seat cushion. Refer to
SE-26, "SEAT CUSHION : Removal and Installation"
.
6.
Remove outer anchor of front seat belt (passenger side). Refer to
.
7.
Remove harness clip.
8.
Turn floor carpet. Refer to
INT-23, "Removal and Installation"
.
9.
Disconnect AWD control module harness connector.
10. Remove AWD control module mounting nuts.
11. Remove AWD control module.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing AWD control module, install it following procedure.
1.
AWD control module
2.
AWD control module harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA2374GB
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст