Freightliner Cargo Maintenance Manual — part 5
IMPORTANT: After performing all operations in this
table, perform all daily and weekly maintenance op-
erations listed in the "Pretrip Inspection and Daily
Maintenance" chapter of the
Cargo Driver’s Manual
.
Also, perform all M1, M2, and M3 Maintenance Inter-
val Operations at the M4 Maintenance Interval.
NOTE: Maintenance operations appearing in italics in
this table are for noise emission control components.
Numbers in this table are maintenance operation ref-
erence numbers matching those in the text of this
manual. The M4 Maintenance consists of all M1, M2,
and M3 Interval Operations plus the other operations
listed below.
M4 Maintenance Interval Operations
Maint.
Oper. No.
M4 Maintenance Interval Operations
Perform All M1 Operations
Perform All M2 Operations
Perform All M3 Operations
Engine-Support Fasteners Checking
Radiator Pressure Flushing and Coolant Changing
Manual Transmission Oil Changing and Magnetic Plug Cleaning
Frame Fastener Torque Checking
All-Axle Alignment Checking
Axle Lubricant Changing and Magnetic Plug Cleaning
Power Steering Reservoir Fluid and Filter Changing
General Information
00
M4 Maintenance Interval Operations Table: 00–13
00/17
IMPORTANT: After performing all operations in this
table, perform all daily and weekly maintenance op-
erations listed in the "Pretrip Inspection and Daily
Maintenance" chapter of the
Cargo Driver’s Manual
.
Also, perform all M1, M2, M3, and M4 Maintenance
Interval Operations at the M5 Maintenance Interval.
NOTE: Numbers in this table are maintenance opera-
tion reference numbers matching those in the text of
this manual. The M5 Maintenance consists of all M1,
M2, M3, and M4 Interval Operations plus the other
operations listed below.
M5 Maintenance Interval Operations
Maint.
Oper. No.
M5 Maintenance Interval Operations
Perform All M1 Operations
Perform All M2 Operations
Perform All M3 Operations
Perform All M4 Operations
Air Dryer Desiccant Replacing, Bendix AD–9
Air Brake Valve Disassembly, Cleaning, and Inspecting, Bendix E–6, QR–1,
and ST–3
General Information
00
M5 Maintenance Interval Operations Table: 00–14
00/18
Maintenance Operation 00–15 (
), summarizes
all Lubrication and Fluid Level Check operations that
must be performed at the M1 Maintenance Interval
for Schedules I, II, and III.
Maintenance operation numbers given in the table
are reference numbers used to help you find detailed
instructions in the manual on the lubrication or fluid
check. Lubrication and Fluid Level Check Locations
can be used as a guide by those who do not
need to consult the detailed lubrication and fluid
check instructions given elsewhere in the manual.
Maintenance Operation 00–15
M1 Lubrication and Fluid Level Check for Schedules I, II, and III
Maint.
Operation
Number
Operation Description
Clutch Release Bearing and Cross-Shaft Lubricating
Clutch Master Cylinder Fluid Level Checking
Manual Transmission Oil Level Checking
Suspension Lubricating
Knuckle Pin Lubricating
Tie-Rod End Lubricating
Axle Lubricant Level Checking
Driveline Lubricating
Foot Brake Valve Actuator Lubricating
Automatic Slack Adjuster Lubricating
Drag Link Lubricating
Power Steering Reservoir Fluid Level Checking
Steering Gear Lubricating (Ross TAS Series)
Cab Mounts Lubricating
Cab Roof Vent Lubricating
Weatherstrip, Door Hinge, and Door Latch Lubricating
Table 7, Maintenance Operation 00-15, M1 Lubrication and Fluid Level Check for
Schedules I, II, and III
General Information
00
Lubrication and Fluid Level Check (M1, schedules I,
II, and III): 00–15
00/19
Maintenance Operation 00–16 (
), summarizes
all Lubrication and Fluid Level Check operations that
must be performed at the M2 Maintenance Interval
for Schedules I, II, and III.
Maintenance operation numbers given in the table
are reference numbers used to help you find detailed
instructions in the manual on the lubrication or fluid
check. Lubrication and Fluid Level Check Locations
can be used as a guide by those who do not
need to consult the detailed lubrication and fluid
check instructions given elsewhere in the manual.
Maintenance Operation 00–16
M2 Lubrication and Fluid Level Check for Schedules I, II, and III
Maint.
Operation
Number
Operation Description
Camshaft Bracket Bushing Lubricating
Air Reservoir Automatic Drain Valve Disassembly, Cleaning, Inspecting,
and Lubricating, Bendix AD–9
Steering Driveline Lubricating
Table 8, Maintenance Operation 00-16, M2 Lubrication and Fluid Level Check for
Schedules I, II, and III
General Information
00
Lubrication and Fluid Level Check (M2, schedules I,
II, and III: 00–16
00/20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст