Suzuki Grand Vitara JB416 / JB420. Manual — part 416

10B-30 Body Electrical Control System:

BCM connector “G31”

G30-7

Rear wiper INT switch

0 – 1 V

↑↓

10 – 14 V

Refer to “Reference waveform No. 3: ”

0 V

Ignition switch is at ON position and rear wiper
switch is at INT position

G30-8

—

—

—

G30-9

Front fog light switch

10 – 14 V

Lighting switch is at CLEARANCE position and
front fog light switch is at ON position

0 V

Lighting switch is at CLEARANCE position and
front fog light switch is at OFF position

G30-10 Lighting switch (HEAD)

10 – 14 V

Lighting switch is at any position other than HEAD
position

0 V

Lighting switch is at HEAD position

G30-11 Lighting switch (CLEARANCE)

10 – 14 V

Lighting switch is at OFF position

0 V

Lighting switch is at any position other than OFF
position

G30-12

Ground for body electrical
controller

0 V

Ignition switch is at each position

G30-13

—

—

—

G30-14

—

—

—

G30-15

—

—

—

G30-16 Theft deterrent light

10 – 14 V

Theft deterrent light is not lit up

0 V

Theft deterrent light is lit up

G30-17

—

—

—

G30-18

—

—

—

G30-19 Serial communication line of SDM

*0 – 1 V

↑↓

4 – 6 V

Refer to “Reference waveform No. 4: ”

G30-20

—

—

—

G30-21 Lighting switch (AUTO)

10 – 14 V

Lighting switch is at other than AUTO position

0 V

Lighting switch is at AUTO position

G30-22 Vehicle speed signal output

*0 – 1 V

↑↓

10 – 14 V

Refer to “Reference waveform No. 5: ”

G30-23

—

—

—

G30-24

—

—

—

Terminal

Circuit

Normal voltage

Condition

Terminal

Circuit

Normal voltage

Condition

G31-1

CAN communication line (high) for
DLC

*2.5 – 3.6 V

Refer to “Reference waveform No. 6: ”

G31-2

CAN communication line (high) for
each control module

*2.5 – 3.6 V

G31-3

CAN communication line (low) for
DLC

*1.6 – 2.5 V

G31-4

CAN communication line (low) for
each control module

*1.6 – 2.5 V

G31-5

—

—

—

G31-6

—

—

—

G31-7

Brake fluid level switch

*5 – 12 V

Refer to “Reference waveform No. 7: ”

0 V

Ignition switch is at ON position and brake fluid
level is lower than MIN level

G31-8

Parking brake switch

*5 – 12 V

Refer to “Reference waveform No. 7: ”

0 V

Ignition switch is at ON position and parking brake
lever is pulled up

G31-9

Oil pressure switch

*6 – 14 V

Refer to “Reference waveform No. 8: ”

0 V

Ignition switch is at ON position and engine is at
stop

Body Electrical Control System: 10B-31

G31-10 Generator “L” terminal

10 – 14 V

Engine is running

0 V

Ignition switch is at ON position

G31-11

—

—

—

G31-12 Tail light relay control

10 – 14 V

Lighting switch is at OFF position

0 V

Lighting switch is at any position other than OFF
position

G31-13 Rear wiper control

10 – 14 V

Ignition switch is at ON position and rear wiper is
not in operation

0 V

Ignition switch is at ON position and rear wiper is in
operation

G31-14

Rear end door window defogger
control

10 – 14 V

Engine is running and rear end door window
defogger is not in operation

0 V

Engine is running and rear end door window
defogger is in operation

G31-15 Horn control

10 – 14 V

Horn is not in operation

0 V

Horn is in operation

G31-16 DRL control

10 – 14 V

Engine is running and lighting switch is at
CLEARANCE or OFF position

0 V

Engine is running and lighting switch is at HEAD
position

G31-17 Front fog light control

10 – 14 V

Lighting switch is at CLEARANCE position and
front fog light switch is at OFF position

0 V

Lighting switch is at CLEARANCE position and
front fog light switch is at ON position

G31-18 Power supply for keyless receiver

4 – 6 V

Ignition switch is at ON position

G31-19 Signal for keyless receiver

*0 – 1 V

↑↓

10 – 14 V

Refer to “Reference waveform No. 9: ”

G31-20 Ground for keyless receiver

0 V

Ignition switch is at each position

G31-21

Sensor ground for outside air
temperature sensor

0 V

Ignition switch is at each position

G31-22

Sensor ground for auto light
sensor

0 V

Ignition switch is at each position

G31-23 Auto-on headlight sensor

0.2 V

Ignition switch is at ON position and cover auto-on
headlight sensor lens by hand

3 – 4 V

Ignition switch is at ON position and light auto-on
headlight sensor lens by 100 W lights

G31-24 Outside air temperature sensor

About 1.5 V

Ignition switch is at ON position and outside air
temperature approx. 20

°C (68 °F)

G31-25 Power supply for auto light sensor

4 – 6 V

Ignition switch is at ON position

G31-26 Manual door lock switch (Unlock)

4 – 6 V

Manual door lock switch is at any position other
than unlock position

0 V

Manual door lock switch is at unlock position

G31-27 Manual door lock switch (Lock)

4 – 6 V

Manual door lock switch is at any position other
than lock position

0 V

Manual door lock switch is at lock position.

G31-28 Power/Normal mode switch

4 – 6 V

Ignition switch is at ON position and Power/Normal
mode switch is at ON position

0 V

Ignition switch is at ON position and Power/Normal
mode switch is at OFF position

G31-29

—

—

—

G31-30

—

—

—

G31-31

—

—

—

G31-32

—

—

—

G31-33

—

—

—

G31-34

Turn signal / hazard warning relay
control

0 V

Hazard warning switch is at ON position

10 – 14 V

Hazard warning switch is at OFF position

G31-35

Serial communication line of data
link connector

10 – 14 V

Ignition switch is at ON position

Terminal

Circuit

Normal voltage

Condition

10B-32 Body Electrical Control System:

BCM connector “G32”

G31-36

Driver side door key cylinder
switch (Unlock)

10 – 14 V

Driver side key cylinder switch is at any position
other than unlock position

0 V

Driver side key cylinder switch is at unlock position

G31-37

Driver side door key cylinder
switch (lock)

10 – 14 V

Driver side key cylinder switch is at any position
other than lock position

0 V

Driver side key cylinder switch is at lock position

G31-38

Door switch (rear end door and
other than driver side door)

10 – 14 V

Rear right and left side door, passenger side door,
rear end door and rear end door are closed

0 V

Any one of the door is opened (except driver side
door)

G31-39 Driver side door switch

10 – 14 V

Driver side door is closed

0 V

Driver side door is opened

G31-40 Driver seat belt switch

*5 – 12 V

Refer to “Reference waveform No. 7: ”

0 V

Ignition switch is at ON position and driver seat
belt is unfastened

Terminal

Circuit

Normal voltage

Condition

Terminal

Circuit

Normal voltage

Condition

G32-1

Ground for door lock motor

0 V

Ignition switch is at each position

G32-2

Rear door lock actuator motor
control (Unlock)

10 – 14 V

Unlock signal is output for rear door lock actuators

0 V

Unlock signal is not output for rear door lock
actuators

G32-3

Door lock actuator motor control
(Lock)

10 – 14 V

Lock signal is output for all door lock actuators

0 V

Lock signal is not output for all door lock actuators

G32-4

—

—

—

G32-5

Power supply for door lock
actuator motor

10 – 14 V

Ignition switch is at each position

G32-6

—

—

—

G32-7

Rear end door lock actuator motor
control (Unlock)

10 – 14 V

Unlock signal is output for rear end door lock
actuator

0 V

Unlock signal is not output for rear end door lock
actuator

G32-8

Driver side door lock actuator
motor control (Unlock)

10 – 14 V

Unlock signal is output for driver side door lock
actuator

0 V

Unlock signal is not output for driver side door lock
actuator

G32-9

Passenger side door lock actuator
motor control (Unlock)

10 – 14 V

Unlock signal is output for passenger side door
lock actuator

0 V

Unlock signal is not output for passenger side door
lock actuator

G32-10

Door lock actuator motor control
(Dead lock cancel)

10 – 14 V

Driver side key cylinder is turned to unlock position

0 V

Driver side key cylinder is at any position other
than unlock position

G32-11

Door lock actuator motor control
(Dead lock set)

10 – 14 V

Driver side key cylinder is turned to lock twice
within 3 seconds

0 V

Driver side key cylinder is at any position other
than lock position

G32-12

Headlight high beam monitor
signal

10 – 14 V

Lighting switch is at HEAD position and dimmer
switch is at low beam position

0 V

Lighting switch is at HEAD position and dimmer
switch is at high beam position

G32-13 Power supply for interior light

10 – 14 V

Ignition switch is at each position

G32-14

—

—

—

G32-15 Interior light control

10 – 14 V

Interior light switch is at DOOR position and
interior light is not lit up

0 V

Interior light switch is at DOOR position and
interior light is lit up

Body Electrical Control System: 10B-33

Reference waveform No. 1
HVAC control module serial communication signal (1)

Reference waveform No. 2
HVAC control module and information display serial
communication signal (1)

Reference waveform No. 3
Rear wiper LOW or INT signal (1)

Reference waveform No. 4
SDM communication signal (1)

Measurement terminal CH1: “G30-4” to “G30-12”
Oscilloscope setting

CH1: 5 V / DIV
TIME: 2 ms / DIV

Measurement
condition

Ignition switch is at ON position

Measurement terminal CH2: “G30-5” to “G30-12”
Oscilloscope setting

CH1: 5 V/DIV
TIME: 10 ms/DIV

Measurement
condition

Ignition switch is at ON position

I5JB0AA20013-01

I5JB0AA20014-01

Measurement terminal Rear wiper LOW signal:

CH1: “G30-6” to “G30-12”
Rear wiper INT signal:
CH1: “G30-7” to “G30-12”

Oscilloscope setting

CH2: 5 V/DIV
TIME: 10 ms/DIV

Measurement
condition

Rear wiper LOW signal:
• Ignition switch is at ON

position, rear wiper switch is
at any position other than
LOW position

Rear wiper INT signal:
• Ignition switch is at ON

position, rear wiper switch is
at any position other than
INT position

Measurement terminal CH1: “G30-19” to “G30-12”
Oscilloscope setting

CH1: 2 V/DIV
TIME: 400 ms/ DIV

Measurement
condition

Ignition switch is at ON position

I5JB0AA20015-01

I5JB0AA20016-01