Suzuki Grand Vitara JB416 / JB420. Manual — part 393

9H-3 Interior Trim:

5 door model

• For equipped with sliding roof, hook on bracket (1) of

roof lining to sliding roof housing (2).

• For equipped with sliding roof, adhere fasteners (1) on

roof lining to fasteners of sliding roof frame securely.

• For tightening torque of seat belt anchor bolt, refer to

“Front Seat Belt Components in Section 8A” and
“Rear Seat Belt Components in Section 8A”.

[C]: Left-hand steering vehicle with sliding roof
[D]: Right-hand steering vehicle with sliding roof

[E]: Left-hand steering vehicle without sliding roof

[F]: Right-hand steering vehicle without sliding roof

1

4

2

1

2

3

4

[C]

1

2

3

3

4

[D]

[E]

1

4

2

3

[F]

I5JB0A980009-01

1

2

I5JB0A980007-01

1

1

I5JB0A980010-01

Interior Trim: 9H-4

Console Box Components

S5JB0A9806003

A

A

A

A

A

A

A

1

2

3

4

I5JB0A980008-02

1. Front console box

3. Gear shift panel

2. Rear console box

4. Console rear panel

9I-1 Sun Roof / T-Top / Convertible Top:

Body, Cab and Accessories

Sun Roof / T-Top / Convertible Top

General Description

Power Sliding (Sun) Roof System Description

S5JB0A9901001

The controller is included in the sliding roof motor unit.
The sliding roof functions are controlled with the sliding roof position data. Sliding roof position and sliding direction are
detected by the controller referring to pulse signals from motor.
Initialization of the sliding roof position data is required in the following situation to reset anti-pinching function: battery
cable or motor connector is disconnected since the sliding roof position data is deleted without power supply to the
motor. Refer to “How to reactivate the system to prevent being pinched by the sunroof” in Sunroof section of Owner’s
manual to initialize the sliding roof position data.

Diagnostic Information and Procedures

Power Sliding (Sun) Roof System Symptom Diagnosis

S5JB0A9904001

Repair Instructions

Sliding (Sun) Roof Glass Components

S5JB0A9906001

Condition

Possible cause

Correction / Reference Item

Sliding roof does not
operate (sliding roof
motor runs OK)

Foreign object stuck in sliding roof rail

Remove or clean stuck object.

Mis-installation of sliding roof rail

Install correctly.

Conflicts of sliding roof parts

Fix conflicts.

Mis-installation of sliding roof drive cable Install correctly.

Sliding roof does not
operate (sliding roof
motor does not run)

Circuit fuse blown

Replace fuse to check for short.

Sliding roof switch faulty

Check sliding roof switch referring to “Sliding
(Sun) Roof Switch Inspection”.

Wiring or grounding faulty

Check circuit referring to “Sliding (Sun) Roof
System Circuit and Motor Inspection”.

Sliding roof motor faulty

Check sliding roof motor referring to “Sliding
(Sun) Roof System Circuit and Motor
Inspection”.

1. Sliding roof glass
2. Bolt
3. Sliding roof cover

1

2

3

2

3

I5JB0A990001-01

Sun Roof / T-Top / Convertible Top: 9I-2

Sliding (Sun) Roof Glass Removal and
Installation

S5JB0A9906002

Removal

1) Open sunshade (1) fully and tilt up sliding roof.

2) Disconnect negative (–) cable at battery.
3) Remove sliding roof covers.
4) Remove sliding roof glass by removing bolts

(TORX

® T25) (1).

Installation
For installation, reverse removal procedure, noting the
following points.

1) Tighten glass fixing bolts temporarily.
2) Initialize sliding roof position data referring to

Owner’s Manual.

3) Position sliding roof glass by closing sliding roof

glass completely.

4) Tighten glass fixing bolts after sliding roof glass

adjustment referring to “Sliding (Sun) Roof Glass
Adjustment”.

Sliding (Sun) Roof Glass Adjustment

S5JB0A9906003

1) Loosen sliding roof glass fixing screws (at 4

locations) and move sliding roof glass (1) up and
down 2 to 3 times. In this way, sliding roof glass can
be positioned in both vertical and horizontal
directions by elasticity of sliding roof weather strip.

2) Position sunroof glass by such dimensions with

respect to roof panel surface as specified below.

Sliding roof glass position (between glass roof
and roof panel)
“a”: 0 mm (0.0 in.)

3) After installing all parts and adjusting properly, check

sunroof for proper operation (open, close and up).

Sliding (Sun) Roof Switch Inspection

S5JB0A9906005

Check switch for continuity between terminals as shown
below.

1

I5JB0A990002-01

1

I5JB0A990003-01

I5JB0A990004-01

SLIDE
OPEN

N

TILT
UP

1

2

3

Switch

Terminal

1

2

3

I5JB0A990005-01