Hummer H3. Manual — part 902
10. Check the gap dimension on the clamp ear.
11. Angulate the C/V joint several times to disperse the grease.
12. Install the inner seal. Refer to Wheel Drive Shaft Inner Joint and Boot Replacement.
DESCRIPTION AND OPERATION
WHEEL DRIVE SHAFTS DESCRIPTION AND OPERATION
Front Wheel Drive Shafts are flexible assemblies which consist of the following components:
Front wheel drive shaft constant velocity joint (outer joint).
Front wheel drive shaft tri-pot joint (inner joint).
The front wheel drive shaft connects the front wheel drive shaft tri-pot joint and the front
wheel drive shaft constant velocity joint.
The front wheel drive shaft tri-pot joint is completely flexible and moves with an in and out
motion.
The front wheel drive shaft constant velocity joint is flexible but can not move in and out.
The Wheel Drive Shaft is a balanced shaft that transmits rotational force from the front
differential to the front wheels when the transfer case is engaged. The wheel drive shaft is
mounted to the front differential by bolting the flange of the wheel drive shaft to the flange on the
inner output shaft of the front differential. The other end of the wheel drive shaft is splined to fit
into and drive the hub assembly when the transfer case is engaged. The tri-pot joint and constant
velocity joint on the wheel drive shaft allows the shaft to be flexible to move with the suspension
travel of the vehicle.
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS
Special Tools
Illustration
Tool Number/Description
J-8059
Drive Axle Seal Clamp Pliers
2007 Hummer H3
2007 Driveline/Axle Wheel Drive Shafts - H3
J-35566
Drive Axle Seal Clamp Pliers
J-35910
Snap Ring Pliers - Parallel Jaw
2007 Hummer H3
2007 Driveline/Axle Wheel Drive Shafts - H3
2007 ACCESSORIES & EQUIPMENT
Bolted Exterior Body Panels and Closures - H3
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fastener Tightening Specifications
REPAIR INSTRUCTIONS
HOOD BUMPER REPLACEMENT
Application
Specification
Metric
English
Check Link Bolt
25 N.m
18 lb ft
Check Strap Nuts
9 N.m
80 lb in
Endgate Assist Rod Stud
10 N.m
89 lb in
Endgate Hinge Bolt
50 N.m
37 lb ft
Fender Mount Bolts
10 N.m
89 lb in
Front Side Door Hinge Bolts
25 N.m
18 lb ft
Grille Support Bolts
9 N.m
27 lb in
Hood Hinge Bolts
25 N.m
18 lb ft
Hood Latch Release Screws
2 N.m
18 lb in
Hood Latch Screws
10 N.m
89 lb in
Rear Side Door Hinge Bolts
25 N.m
18 lb ft
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - H3
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - H3
Fig. 1: Hood Bumper Replacement
Courtesy of GENERAL MOTORS CORP.
Hood Bumper Replacement
HOOD PRIMARY LATCH RELEASE CABLE REPLACEMENT
Removal Procedure
1. Remove the grille. Refer to Grille Replacement .
2. Remove the hood latch. Refer to Hood Latch Replacement.
Callout
Component Name
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications.
1
Bumper, Hood Bumper
Tip: Adjust bumper as necessary.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст