Hummer H1 (2006+). Manual — part 303
10-74 Body
______________________________________________________________________
Figure 10-85: Guide Bracket Assembly Location
8.
Lubricate all the hood stops, hinges and the guide brackets. Latch the hood.
9.
Test drive to ensure proper alignment (no squeaks).
10. Check the headlight aim and adjust it if necessary.
Figure 10-86: Hood Latch and Stop Location
Side Hood Stop Replacement
Removal
Remove the two bolts, washers and the side hood stop from the body (Figure 10-86).
Installation
Apply a silicone sealer to the bottom and secure the side hood stop to the body with the two washers and bolts. Tighten the bolts to
6 lb-ft (8 N•m) (Figure 10-86).
HOOD
GUIDE BRACKET ASSEMBLY
HOOD LATCH
SIDE HOOD
STOP
_____________________________________________________________________
Body 10-75
Grille and Screen Replacement
Removal
1.
Remove the six locknuts, washers, bolts, washers and the grille from the hood (Figure 10-87).
2.
Remove the six locknuts, washers, screws, washers and the screen from grille.
Installation
1.
Secure the screen to the grille with the six washers, screws, washers and the locknuts. Tighten the locknuts to 6 lb-ft (8 N•m)
(Figure 10-87).
2.
Secure the grille to the hood with the six washers, screws, washers and the locknuts. Tighten the locknuts to 7 lb-ft (9 N•m).
Figure 10-87: Grille and Screen Replacement
Center Hood Stop Replacement
Removal
Remove the two bolts, washers, center hood stop and the plate from the A-beam (Figure 10-88).
Installation
Secure the center hood stop and the plate to the A-beam with the two washers and the bolts. Tighten the bolts to 12 lb-ft (16 N•m)
(Figure 10-88).
GRILLE
HOOD
SCREEN
10-76 Body
______________________________________________________________________
Figure 10-88: Center Hood Stop Replacement
Guide Bracket Assembly Replacement
Removal
Remove the six locknuts, twelve washers, guide bracket assembly, two guide plates and the six bolts from the hood (Figure
10-89).
Installation
1.
Loosely attach the guide plate and the guide bracket assembly to the hood with the six bolts, twelve washers and the six lock-
nuts. Tighten the locknuts to 10 lb-ft (14 N•m) (Figure 10-89).
2.
Lower the hood and align the guide bracket assembly with the center hood stop on the A-beam (Figure 10-88).
3.
Mark the guide bracket assembly position, raise the hood and tighten the locknuts to 10 lb-ft (14 N•m) (Figure 10-89).
Figure 10-89: Bracket Assembly Replacement
Front Hood Screen Replacement
Removal
1.
Remove the three locknuts, washers and the carriage bolts securing the front hood screen to the hood (Figure 10-90).
2.
Remove the three bolts, harness clamps, washers and the front hood screen from the hood.
A-BEAM
CENTER
HOOD
STOP
PLATE
GUIDE PLATE
HOOD
GUIDE
ASSEMBLY
BRACKET
_____________________________________________________________________
Body 10-77
Installation
1.
Secure the front hood screen to the hood with the three washers, harness clamps and the bolts. Tighten the bolts to 20-30 lb in.
(2-3 N•m) (Figure 10-90).
2.
Secure the front hood screen to the hood with the three carriage bolts, washers and the locknuts. Tighten the locknuts to 21 lb-
ft (29 N•m).
Figure 10-90: Front Hood Screen Replacement
HOOD
HARNESS
CLAMP
FRONT HOOD SCREEN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст